Double ion implantation and pulsed laser melting processes for third generation solar cells

In the framework of the third generation of photovoltaic devices, the intermediate band solar cell is one of the possible candidates to reach higher efficiencies with a lower processing cost. In this work, we introduce a novel processing method based on a double ion implantation and, subsequently, a pulsed laser melting (PLM) process to obtain thicker layers of Ti supersaturated Si. We perform ab initio theoretical calculations of Si impurified with Ti showing that Ti in Si is a good candidate to theoretically form an intermediate band material in the Ti supersaturated Si. From time-of-flight secondary ion mass spectroscopy measurements, we confirm that we have obtained a Ti implanted and PLM thicker layer of 135 nm. Transmission electron microscopy reveals a single crystalline structure whilst the electrical characterization confirms the transport properties of an intermediate band material/Si substrate junction. High subbandgap absorption has been measured, obtaining an approximate value of 10 4 cm(-1) in the photons energy range from 1.1 to 0.6 eV

Electrical characterization of amorphous silicon MIS-based structures for HIT solar cell applications

A complete electrical characterization of hydrogenated amorphous silicon layers (a-Si:H) deposited on crystalline silicon (c-Si) substrates by electron cyclotron resonance chemical vapor deposition (ECR-CVD) was carried out. These structures are of interest for photovoltaic applications. Different growth temperatures between 30 and 200 °C were used. A rapid thermal annealing in forming gas atmosphere at 200 °C during 10 min was applied after the metallization process. The evolution of interfacial state density with the deposition temperature indicates a better interface passivation at higher growth temperatures. However, in these cases, an important contribution of slow states is detected as well. Thus, using intermediate growth temperatures (100–150 °C) might be the best choice

Room temperature photo-response of titanium supersaturated silicon at energies over the bandgap

Silicon samples were implanted with high Ti doses and subsequently processed with the pulsed-laser melting technique. The electronic transport properties in the 15–300 K range and the room temperature spectral photoresponse at energies over the bandgap were measured. Samples with Ti concentration below the insulator-metal (I-M) transition limit showed a progressive reduction of the carrier lifetime in the implanted layer as Ti dose is increased. However, when the Ti concentration exceeded this limit, an extraordinary recovery of the photoresponse was measured. This result supports the theory of intermediate band materials and is of utmost relevance for photovoltaic cells and Si-based detectors

On the properties of GaP supersaturated with Ti

We have fabricated GaP supersaturated with Ti by means of ion implantation and pulsed-laser melting to obtain an intermediate band material with applications in photovoltaics. This material has a strong sheet photoconductance at energies below the bandgap of GaP and it seems to be passivated by a Ga defective GaPO oxide layer during the laser process. Passivation is consistently analyzed by sheet photoconductance and photoluminescence measurements. We report on the structural quality of the resulting layers and analyze the energy of the new optical transitions measured on GaP:Ti. A collapse found in the sheet photoconductance spectra of GaP:Ti samples fabricated on undoped substrates is explained by the negative photoconductivity phenomenon. (C) 2019 Elsevier B.V. All rights reserved

Deposition of Intrinsic a-Si:H by ECR-CVD to Passivate the Crystalline Silicon Heterointerface in HIT Solar Cells

We have deposited intrinsic amorphous silicon (a-Si:H) using the electron cyclotron resonance (ECR) chemical vapor deposition technique in order to analyze the a-Si:H/c-Si heterointerface and assess the possible application in heterojunction with intrinsic thin layer (HIT) solar cells. Physical characterization of the deposited films shows that the hydrogen content is in the 15-30% range, depending on deposition temperature. The optical bandgap value is always comprised within the range 1.9- 2.2 eV. Minority carrier lifetime measurements performed on the heterostructures reach high values up to 1.3 ms, indicating a well-passivated a-Si:H/c-Si heterointerface for deposition temperatures as low as 100°C. In addition, we prove that the metal-oxide- semiconductor conductance method to obtain interface trap distribution can be applied to the a-Si:H/c-Si heterointerface, since the intrinsic a-Si:H layer behaves as an insulator at low or negative bias. Values for the minimum of D_it as low as 8 × 10^10 cm^2 · eV^-1 were obtained for our samples, pointing to good surface passivation properties of ECR-deposited a-Si:H for HIT solar cell applications

Mejora de las Metodologías Docentes para el área de la Electrónica

Fac. de Ciencias FísicasFALSEsubmitte

A robust method to determine the contact resistance using the van der Pauw set up

The van der Pauw method to calculate the sheet resistance and the mobility of a semiconductor is a pervasive technique both in the microelectronics industry and in the condensed matter science field. There are hundreds of papers dealing with the influence of the contact size, nonuniformities and other second order effects. In this paper we will develop a simple methodology to evaluate the error produced by finite size contacts, detect the presence of contact resistance, calculate it for each contact, and determine the linear or rectifying behavior of the contact. We will also calculate the errors produced by the use of voltmeters with finite input resistance in relation with the sample sheet resistance

Limitations of high pressure sputtering for amorphous silicon deposition

Amorphous silicon thin films were deposited using the high pressure sputtering (HPS) technique to study the influence of deposition parameters on film composition, presence of impurities, atomic bonding characteristics and optical properties. An optical emission spectroscopy (OES) system has been used to identify the different species present in the plasma in order to obtain appropriate conditions to deposit high purity films. Composition measurements in agreement with the OES information showed impurities which critically depend on the deposition rate and on the gas pressure. We prove that films deposited at the highest RF power and 3.4 × 10^−2 mbar, exhibit properties as good as the ones of the films deposited by other more standard techniques

Sub-bandgap external quantum efficiency in Ti implanted Si heterojunction with intrinsic thin layer cells

In this work we present the manufacturing processes and results obtained from the characterization of heterojunction with intrinsic thin layer solar cells that include a heavily Ti ion implanted Si absorbing layer. The cells exhibit external circuit photocurrent at photon energies well below the Si bandgap. We discuss the origin of this below-bandgap photocurrent and the modifications in the hydrogenated amorphous intrinsic Si layer thickness to increase the open-circuit voltage. © 2013 The Japan Society of Applied Physics.This work has been supported by the Regional Government of Comunidad de Madrid within the project NUMANCIA II (S-2009/ENE-1477). J. Olea and D. Pastor would like to acknowledge a Juan de la Cierva fellowship from the Spanish Science Ministry (JCI-2011-10402, JCI-2011-11471). E. Antolín acknowledges a Marie Curie Fellowship from the European Commission (Project Siracusa, Grant PIEF-GA-2011-302489.S-2009/ENE-1477/NUMANCIA-IIPeer Reviewe