261 research outputs found
Numerical optimization of integrating cavities for diffraction-limited millimeter-wave bolometer arrays
Far-infrared to millimeter-wave bolometers designed to make astronomical observations are typically encased in integrating cavities at the termination of feedhorns or Winston cones. This photometer combination maximizes absorption of radiation, enables the absorber area to be minimized, and controls the directivity of absorption, thereby reducing susceptibility to stray light. In the next decade, arrays of hundreds of silicon nitride micromesh bolometers with planar architectures will be used in ground-based, suborbital, and orbital platforms for astronomy. The optimization of integrating cavity designs is required for achieving the highest possible sensitivity for these arrays. We report numerical simulations of the electromagnetic fields in integrating cavities with an infinite plane-parallel geometry formed by a solid reflecting backshort and the back surface of a feedhorn array block. Performance of this architecture for the bolometer array camera (Bolocam) for cosmology at a frequency of 214 GHz is investigated. We explore the sensitivity of absorption efficiency to absorber impedance and backshort location and the magnitude of leakage from cavities. The simulations are compared with experimental data from a room-temperature scale model and with the performance of Bolocam at a temperature of 300 mK. The main results of the simulations for Bolocam-type cavities are that (1) monochromatic absorptions as high as 95% are achievable with <1% cross talk between neighboring cavities, (2) the optimum absorber impedances are 400 Ω/sq, but with a broad maximum from ~150 to ~700 Ω/sq, and (3) maximum absorption is achieved with absorber diameters ≥1.5λ. Good general agreement between the simulations and the experiments was found
A Fluctuation Analysis of the Bolocam 1.1mm Lockman Hole Survey
We perform a fluctuation analysis of the 1.1mm Bolocam Lockman Hole Survey,
which covers 324 square arcmin to a very uniform point source-filtered RMS
noise level of 1.4 mJy/beam. The fluctuation analysis has the significant
advantage of utilizing all of the available data. We constrain the number
counts in the 1-10 mJy range, and derive significantly tighter constraints than
in previous work: the power-law index is 2.7 (+0.18, -0.15), while the
amplitude is equal to 1595 (+85,-238) sources per mJy per square degree, or
N(>1 mJy) = 940 (+50,-140) sources/square degree (95% confidence). Our results
agree extremely well with those derived from the extracted source number counts
by Laurent et al (2005). Our derived normalization is about 2.5 times smaller
than determined by MAMBO at 1.2mm by Greve et al (2004). However, the
uncertainty in the normalization for both data sets is dominated by the
systematic (i.e., absolute flux calibration) rather than statistical errors;
within these uncertainties, our results are in agreement. We estimate that
about 7% of the 1.1mm background has been resolved at 1 mJy.Comment: To appear in the Astrophysical Journal; 22 pages, 9 figure
Bolocam: a millimeter-wave bolometric camera
We describe the design of Bolocam, a bolometric camera for millimeter-wave observations at the Caltech Submillimeter Observatory. Bolocam will have 144 diffraction-limited detectors operating at 300 mK, an 8 arcminute field of view, and a sky noise limited NEFD of approximately 35 mJy Hz^(-1/2) per pixel at λ = 1.4 mm. Observations will be possible at one of (lambda) equals 1.1., 1.4, or 2.1 mm per observing run. The detector array consists of sensitive NTD Ge thermistors bonded to silicon nitride micromesh absorbers patterned on a single wafer of silicon. This is a new technology in millimeter-wave detector array construction. To increase detector packing density, the feed horns will be spaced by 1.26 fλ (at λ = 1.4 mm), rather than the conventional 2fλ . DC stable read out electronics will enable on-the-fly mapping and drift scanning. We will use Bolocam to map Galactic dust emission, to search for protogalaxies, and to observe the Sunyaev- Zel'dovich effect toward galaxy clusters
Noise Properties of the BOOMERANG Instrument
In this paper we report a short description of the BOOMERANG experiment explaining his scientific goal and the technologies implied. We concentrate then on the analysis of the noise properties discussing in particular the scan synchronous noise. Finally we present the calibration technique and the sensitivity of all the channels
Current status of Bolocam: a large-format millimeter-wave bolometer camera
We describe the design and performance of Bolocam, a 144-element, bolometric, millimeter-wave camera. Bolocam is currently in its commissioning stage at the Caltech Submillimeter Observatory. We compare the instrument performance measured at the telescope with a detailed sensitivity model, discuss the factors limiting the current sensitivity, and describe our plans for future improvements intended to increase the mapping speed
B2K: The polarization-sensitive BOOMERanG experiment
We describe the new BOOMERanG payload, which is being prepared for a new circum-antarctic flight, with the aim to detect the linear polarization of the Cosmic Microwave Background (CMB). In addition to polarization capabilities, obtained by means of special bolometers, the instrument has been improved in the attitude reconstruction system and in the calibration system
Science Impacts of the SPHEREx All-Sky Optical to Near-Infrared Spectral Survey: Report of a Community Workshop Examining Extragalactic, Galactic, Stellar and Planetary Science
SPHEREx is a proposed SMEX mission selected for Phase A. SPHEREx will carry
out the first all-sky spectral survey and provide for every 6.2" pixel a
spectra between 0.75 and 4.18 m [with R41.4] and 4.18 and 5.00
m [with R135]. The SPHEREx team has proposed three specific science
investigations to be carried out with this unique data set: cosmic inflation,
interstellar and circumstellar ices, and the extra-galactic background light.
It is readily apparent, however, that many other questions in astrophysics and
planetary sciences could be addressed with the SPHEREx data. The SPHEREx team
convened a community workshop in February 2016, with the intent of enlisting
the aid of a larger group of scientists in defining these questions. This paper
summarizes the rich and varied menu of investigations that was laid out. It
includes studies of the composition of main belt and Trojan/Greek asteroids;
mapping the zodiacal light with unprecedented spatial and spectral resolution;
identifying and studying very low-metallicity stars; improving stellar
parameters in order to better characterize transiting exoplanets; studying
aliphatic and aromatic carbon-bearing molecules in the interstellar medium;
mapping star formation rates in nearby galaxies; determining the redshift of
clusters of galaxies; identifying high redshift quasars over the full sky; and
providing a NIR spectrum for most eROSITA X-ray sources. All of these
investigations, and others not listed here, can be carried out with the nominal
all-sky spectra to be produced by SPHEREx. In addition, the workshop defined
enhanced data products and user tools which would facilitate some of these
scientific studies. Finally, the workshop noted the high degrees of synergy
between SPHEREx and a number of other current or forthcoming programs,
including JWST, WFIRST, Euclid, GAIA, K2/Kepler, TESS, eROSITA and LSST.Comment: Report of the First SPHEREx Community Workshop,
http://spherex.caltech.edu/Workshop.html , 84 pages, 28 figure
Current status of Bolocam: a large-format millimeter-wave bolometer camera
We describe the design and performance of Bolocam, a 144-element, bolometric, millimeter-wave camera. Bolocam is currently in its commissioning stage at the Caltech Submillimeter Observatory. We compare the instrument performance measured at the telescope with a detailed sensitivity model, discuss the factors limiting the current sensitivity, and describe our plans for future improvements intended to increase the mapping speed
- …