Removal of NOx from diesel generator exhaust by pulsed electron beams

The objective of this paper is to determine the effects of electron beam pulse parameters on the utilization of the reactive free radicals for removal of NO{sub x} from diesel generator exhaust. A dose per pulse less than 1 kGy has been determined to be optimum for effective radical utilization. During each post-pulse period, the radicals are utilized in the removal of NO{sub x} in a timescale of around 100 microseconds; thus, with pulse frequencies of around 10 kHz or less, the radical concentrations remain sufficiently low to prevent any significant competition between radical-pollutant and radical-radical reactions. It is shown that a pulsed electron beam reactor, operating with a dose per pulse of less than 1 kGy/pulse and pulse repetition rate of less than 10 kHz, will have the same plasma chemistry efficiency (parts per million of removed NO{sub x} per kGy of electron beam dose) as an electron beam reactor operating with a low dose rate of 50 kGy/s in continuous mode. Ozone accumulation is a limiting factor under high pulse frequency conditions. The total dose requirement determines the optimum combination of dose per pulse and pulse frequency for both radical utilization and prevention of ozone buildup

Sulfur Tolerance of Selective Partial Oxidation of NO to NO2 in a Plasma

Several catalytic aftertreatment technologies rely on the conversion of NO to NO2 to achieve efficient reduction of NOx and particulates in diesel exhaust. These technologies include the use of selective catalytic reduction of NOx with hydrocarbons, NOx adsorption, and continuously regenerated particulate trapping. These technologies require low sulfur fuel because the catalyst component that is active in converting NO to NO2 is also active in converting SO2 to SO3 . The SO3 leads t o increase in particulates and/or poison active sites on the catalyst. A non-thermal plasma can be used for the selective partial oxidation of NO to NO2 in the gas-phase under diesel engine exhaust conditions. This paper discusses how a non-thermal plasma can efficiently oxidize NO to NO2 without oxidizing SO2 to SO3

Final report pulsed plasma processing of effluent pollutants and hazardous chemicals

The electrical discharge techniques, called non-thermal, utilize high voltage breakdown of gases using short pulses of one to a few hundred nanoseconds. These short pulses between metal electrodes generate energetic electrons without appreciable thermal heating of the gas. The energetic electrons collide with gas molecules to form radicals. The radicals then react with pollutants to form harmless compounds. Our non-thermal experimental device used a wire in a pipe geometry. The wire was driven by a 40 kilovolt pulse 100 nanoseconds long. Gas was circulated in a loop through the pipe geometry in a closed system. This system permitted the introduction of various gas combinations prior to testing. The recirculated gas was heated to determine the effect on the electrical discharge, and chemical reactions. Additives were introduced to improve the efficiency (defined as energy input per unit molecule destroyed). The efficient was found to be the most important parameter in that the experiments generally required high energy inputs. However, we were able to significantly improve the efficiency of NO removal by the addition of hydrocarbons, nitric oxide has been removed with an energy cost of 15 ev per NO molecule. We believe the hydrocarbon additive serves by recycling the hydroxyl radicals during the oxidation of NO. The implementation of this process will depend largely on how much additives, electrical power consumption, and final NO{sub x} concentration are acceptable for a particular application

The anti-tumor effect of Apo2L/TRAIL on patient pancreatic adenocarcinomas grown as xenografts in SCID mice

BACKGROUND: Apo2L/TRAIL has considerable promise for cancer therapy based on the fact that this member of the tumor necrosis factor family induces apoptosis in the majority of malignant cells, while normal cells are more resistant. Furthermore, in many cells, when Apo2L/TRAIL is combined with chemotherapy, the effect is synergistic. The majority of this work has been carried out using cell lines. Therefore, investigation of how patient tumors respond to Apo2L/TRAIL can validate and/or complement information obtained from cell lines and prove valuable in the design of future clinical trials. METHODS: We have investigated the Apo2L/TRAIL sensitivity of patient derived pancreatic tumors using a patient tumor xenograft/ SCID mouse model. Mice bearing engrafted tumors were treated with Apo2L/TRAIL, gemcitabine or a combination of both therapies. RESULTS: Patient tumors grown as xenografts exhibited a spectrum of sensitivity to Apo2L/TRAIL. Both Apo2L/TRAIL sensitive and resistant pancreatic tumors were found, as well as tumors that showed heterogeneity of response. Changes in apoptotic signaling molecules in a sensitive tumor were analyzed by Western blot following Apo2L/TRAIL treatment; loss of procaspase 8, Bid and procaspase 3 was observed and correlated with inhibition of tumor growth. However, in a tumor that was highly resistant to killing by Apo2L/TRAIL, although there was a partial loss of procaspase 8 and Bid in response to Apo2L/TRAIL treatment, loss of procaspase 3 was negligible. This resistant tumor also expressed a high level of the anti-apoptotic molecule Bcl-X(L )that, in comparison, was not detected in a sensitive tumor. Importantly, in the majority of these tumors, addition of gemcitabine to Apo2L/TRAIL resulted in a greater anti-tumor effect than either therapy used alone. CONCLUSION: These data suggest that in a clinical setting we will see heterogeneity in the response of patients' tumors to Apo2L/TRAIL, including tumors that are highly sensitive as well as those that are resistant. While much more work is needed to understand the molecular basis for this heterogeneity, it is very encouraging, that Apo2L/TRAIL in combination with gemcitabine increased therapeutic efficacy in almost every case and therefore may be a highly effective strategy for controlling human pancreatic cancer validating and expanding upon what has been reported for cell lines

Nonthermal aftertreatment of diesel engine exhaust

The ultimate objective of this work has been to develop a nonthermal plasma process to reduce NO{sub x} in diesel exhaust gas. A secondary objective has been to study the possibility of particulate matter (soot) reduction by the same technique. The early work revealed a fundamental difficulty with this NO{sub x} reduction approach in the gas environment of the diesel engine exhaust. These observations necessitated a thorough study of the unfavorable chemistry in the hope that knowledge of the chemical mechanism would offer an opportunity to make the approach useful for NO{sub x} reduction. Whereas fundamental understanding of the mechanism has been obtained, the authors have not found any measure that would make the approach meet its original objective

Tabletop X-ray Lasers

Details of schemes for two tabletop size x‐ray lasers that require a high‐intensity short‐pulse driving laser are discussed. The first is based on rapid recombination following optical‐field ionization. Analytical and numerical calculations of the output properties are presented. Propagation in the confocal geometry is discussed and a solution for x‐ray lasing in Li‐like N at 247 Å is described. Since the calculated gain coefficient depends strongly on the electron temperature, the methods of calculating electron heating following field ionization are discussed. Recent experiments aimed at demonstrating lasing in H‐like Li at 135 Å are discussed along with modeling results. The second x‐ray laser scheme is based on the population inversion obtained during inner‐shell photoionization by hard x rays. This approach has significantly higher‐energy requirements, but lasing occurs at very short wavelengths (λ ≤ 15 Å). Experiments that are possible with existing lasers are discussed

EUV spectra of highly-charged ions W54+^{54+}-W63+^{63+} relevant to ITER diagnostics

We report the first measurements and detailed analysis of extreme ultraviolet (EUV) spectra (4 nm to 20 nm) of highly-charged tungsten ions W$^{54+}$ to W$^{63+}$ obtained with an electron beam ion trap (EBIT). Collisional-radiative modelling is used to identify strong electric-dipole and magnetic-dipole transitions in all ionization stages. These lines can be used for impurity transport studies and temperature diagnostics in fusion reactors, such as ITER. Identifications of prominent lines from several W ions were confirmed by measurement of isoelectronic EUV spectra of Hf, Ta, and Au. We also discuss the importance of charge exchange recombination for correct description of ionization balance in the EBIT plasma.Comment: 11 pages, 4 figure

Electron-impact ionization of air molecules and its application to the abatement of volatile organic compounds

In this paper the authors present data on the non-thermal plasma processing of two representative VOCs: carbon tetrachloride and methanol. The investigation used a compact electron beam reactor, and two types of discharge reactors: a pulsed corona and a dielectric-barrier discharge. To the knowledge of the authors, this is the first comparison of the energy efficiency of electron beam, pulsed corona and dielectric-barrier discharge processing of these VOCs under identical gas conditions. For most electrical discharge reactors the analysis suggests that the attainable electron mean energy is rather limited and cannot be significantly enhanced by changing the electrode configuration or voltage waveform. The experimental data confirms that there is no significant difference in the performance of the pulsed corona and dielectric-barrier discharge reactors. The authors observe that electron beam processing is remarkably more energy efficiency than electrical discharge processing in decomposing either of these VOC molecules. During electron beam processing, the specific energy consumption is consistent with the energy required for the ionization of the background air molecules. For carbon tetrachloride, the dominant decomposition pathway is dissociative electron attachment. For methanol, the dominant decomposition pathway is dissociative charge exchange

Non-thermal plasma techniques for abatement of volatile organic compounds and nitrogen oxides

Non-thermal plasma processing is an emerging technology for the abatement of volatile organic compounds (VOCs) and nitrogen oxides (NO{sub x}) in atmospheric-pressure air streams. Either electrical discharge or electron beam methods can produce these plasmas. Each of these methods can be implemented in many ways. There are many types of electrical discharge reactors, the variants depending on the electrode configuration and electrical power supply (pulsed, AC or DC). Two of the more extensively investigated types of discharge reactors are based on the pulsed corona and dielectric-barrier discharge. Recently, compact low-energy (<200 keV) electron accelerators have been developed to meet the requirements of industrial applications such as crosslinking of polymer materials, curing of solvent-free coatings, and drying of printing inks. Special materials have also been developed to make the window thin and rugged. Some of these compact electron beam sources are already commercially available and could be utilized for many pollution control applications. In this paper we will present a comparative assessment of various nonthermal plasma reactors. The thrust of our work has been two-fold: (1) to understand the scalability of various non-thermal plasma reactors by focusing on the energy efficiency of the electron and chemical kinetics, and (2) to identify the byproducts to ensure that the effluent gases from the processor are either benign or much easier and less expensive to dispose of compared to the original pollutants. We will present experimental results using a compact electron beam reactor and various types of electrical discharge reactors. We have used these reactors to study the removal of NO{sub x} and a wide variety of VOCS. We have studied the effects of background gas composition and gas temperature on the decomposition chemistry

Modeling of laser damage initiated by surface contamination

The authors are engaged in a comprehensive effort to understand and model the initiation and growth of laser damage initiated by surface contaminants. This includes, for example, the initial absorption by the contaminant, heating and plasma generation, pressure and thermal loading of the transparent substrate, and subsequent shockwave propagation, `splashing` of molten material and possible spallation, optical propagation and scattering, and treatment of material fracture. The integration use of large radiation hydrodynamics codes, optical propagation codes and material strength codes enables a comprehensive view of the damage process The following picture of surface contaminant initiated laser damage is emerging from our simulations