Off-diagonal impedance in amorphous wires and application to linear magnetic sensors

The magnetic-field behaviour of the off-diagonal impedance in Co-based amorphous wires is investigated under the condition of sinusoidal (50 MHz) and pulsed (5 ns rising time) current excitations. For comparison, the field characteristics of the diagonal impedance are measured as well. In general, when an alternating current is applied to a magnetic wire the voltage signal is generated not only across the wire but also in the coil mounted on it. These voltages are related with the diagonal and off-diagonal impedances, respectively. It is demonstrated that these impedances have a different behaviour as a function of axial magnetic field: the former is symmetrical and the latter is antisymmetrical with a near linear portion within a certain field interval. In the case of the off-diagonal response, the dc bias current eliminating circular domains is necessary. The pulsed excitation that combines both high and low frequency harmonics produces the off-diagonal voltage response without additional bias current or field. This suits ideal for a practical sensor circuit design. The principles of operation of a linear magnetic sensor based on C-MOS transistor circuit are discussed.Comment: Accepted to IEEE Trans. Magn. (2004

Ferromagnetic Wires Composite Media with Tunable Scattering Spectra at Microwaves

We demonstrate composite media with ferromagnetic wires that exhibit a frequency region at the microwave regime with scattering spectra strongly dependent on an external magnetic field or stress. These tunable composite materials have recently been proposed theoretically; however, no direct experimental verification has been reported. We used composite materials with predominantly oriented CoFeCrSiB glass-coated amorphous wires having large magnetoimpedance at GHz frequencies. The free space measurements of reflection and transmission coefficients were conducted in the frequency range 1-8 GHz in the presence of an external static magnetic field or stress applied to the whole sample. In general, the transmission spectra show greater changes in the range of 10dB for a relatively small magnetic field of few Oe or stress of 0.1 MPa. The obtained results are quantitatively consistent with the analytical expressions predicted by the effective medium arguments. The incident electromagnetic wave induces an electrical dipole moment in each wire, the aggregate of which forms the effective dipole response of the whole composite structure in the radiative near or far field region. The field and stress dependences of the effective response arise from a field or tensile stress sensitivity of the ac surface impedance of a ferromagnetic wire. In the vicinity of the antenna resonance the variations in the magneto-impedance of the wire inclusions result in large changes of the total effective response. A number of applications of proposed materials is discussed including the field tunable microwave surfaces and the self-sensing media for the remote non-destructive evaluation of structural materials

Stress effect on magnetoimpedance (MI) in amorphous wires at GHz frequencies and application to stress-tunable microwave composite materials

The effect of tensile stress on magnetoimpedance (MI) in CoMnSiB amorphous wires at microwave frequencies (0.5-3 GHz) is investigated both experimentally and theoretically. In the presence of the dc bias magnetic field of the order of the anisotropy field, the impedance shows very large and sensitive change when the wire is subjected to a tensile stress: 100% and 60% per 180 MPa for frequencies 500 MHz and 2.5 GHz, respectively. It is demonstrated that this behavior owes mainly to the directional change in the equilibrium magnetization caused by the applied stress and field, which agrees well with the theoretical results for the surface impedance. This stress effect on MI is proposed to use for creating microwave stress-tunable composite materials containing short magnetic wires. The analysis of the dielectric response from such materials shows that depending on the stress level in the material, the dispersion of the effective permittivity can be of a resonant or relaxation type with a considerable change in its values (up to 100% at 600 MPa). This media can be used for structural stress monitoring by microwave contrast imaging

Five-Year Experience In Surgical Treatment Of Temporal Bone Paragangliomas

The article describes our five-year experience in the surgical treatment of temporal bone paragangliomas. Considering our experience, the surgical treatment of patients with different types of paragangliomas based on a detailed study of the CT scan and MRI data using the preoperative selective embolization of tumor-feeding vessels and the navigation system intraoperatively as well as the endoscopy assistance allows total removing of the tumor with minimal damaging of the vital structures of the lateral skull base

Optomagnetic composite medium with conducting nanoelements

A new type of metal-dielectric composites has been proposed that is characterised by a resonance-like behaviour of the effective permeability in the infrared and visible spectral ranges. This material can be referred to as optomagnetic medium. The analytical formalism developed is based on solving the scattering problem for considered inclusions with impedance boundary condition, which yields the current and charge distributions within the inclusions. The presence of the effective magnetic permeability and its resonant properties lead to novel optical effects and open new possible applications.Comment: 48 pages, 13 figures. accepted to Phys. Rev. B; to appear vol. 66, 200

ANALYSIS OF POSSIBLE ENHANCEMENT OF PROPERTIES OF VK15 MATERIAL USED FOR DRILLING TOOLS

Traditionally, when drilling hard and abrasive rocks, it is recommended to use a tungsten-cobalt hard alloy VK15. The analysis of information on the possibility of improving the potential of the material has demonstrated the existence of mechanisms that provide structural transformations that enhance its strength, hardness and toughness. The use of such technology instead of traditional methods will lead to an increase in the operating efficiency and durability of the tool. During the work, experimental samples of alloy VK15 were obtained by sintering in four different modes. Then their properties were analyzed. The results of the metallographic study carried out on the «Carl Zeiss» microscope made it possible to estimate the distribution of tungsten carbide grains in cobalt bon and show the grinding of the carbide phase. Thus, with traditional sintering, the amount of tungsten carbide grains with an average size of less than 1 μm in diameter from the entire size range reaches 19.5 %, while after additional heat treatment with a holding time of 1280 °C, the value was 41.5 %; 900 °C – 59.1 %; 600 °С – 54.5 %. The maximum improvement results were the following: hardness by 18 %, a coercive force by 49 %, and crack resistance by 11 % of the traditional alloy, there were achieved at 900-1280 °C. A hypothesis has been put forward on the formation of additional structural elements not detected by the methods of optical metallography. Studies of the topology and structure of the samples on an atomic force microscope confirmed the presence of nanoscale inclusions from 20 to 40 nm (presumably tungsten carbide) in a cobalt bond. For VK15, comparative studies of properties and analysis of the microstructure of experimental samples obtained by the traditional sintering and modified technology have shown that the sintering mode at 900 °C is a priority. Thus, the developed technology, including the sintering of powders in a hydrogen stream up to 750 °C, from 750 to 1450 °C in vacuum, feeding at a maximum temperature of 1450 °C for 15 minutes of argon at a pressure of 60 bar, subsequent cooling to 900 °C and 1 hour exposure, can be recommended as the most rational conditions for revealing the potential of the material and providing an enhanced level of properties of the drilling tool