Si3N4 single-crystal nanowires grown from silicon micro and nanoparticles near the threshold of passive oxidation

A simple and most promising oxide-assisted catalyst-free method is used to prepare silicon nitride nanowires that give rise to high yield in a short time. After a brief analysis of the state of the art, we reveal the crucial role played by the oxygen partial pressure: when oxygen partial pressure is slightly below the threshold of passive oxidation, a high yield inhibiting the formation of any silica layer covering the nanowires occurs and thanks to the synthesis temperature one can control nanowire dimensions

Diamond electro-optomechanical resonators integrated in nanophotonic circuits

Diamond integrated photonic devices are promising candidates for emerging applications in nanophotonics and quantum optics. Here we demonstrate active modulation of diamond nanophotonic circuits by exploiting mechanical degrees of freedom in free-standing diamond electro-optomechanical resonators. We obtain high quality factors up to 9600, allowing us to read out the driven nanomechanical response with integrated optical interferometers with high sensitivity. We are able to excite higher order mechanical modes up to 115 MHz and observe the nanomechanical response also under ambient conditions.Comment: 15 pages, 4 figure

Evaporative Cooling of a Guided Rubidium Atomic Beam

We report on our recent progress in the manipulation and cooling of a magnetically guided, high flux beam of $^{87}{\rm Rb}$ atoms. Typically $7\times 10^9$ atoms per second propagate in a magnetic guide providing a transverse gradient of 800 G/cm, with a temperature $\sim550$ $\mu$K, at an initial velocity of 90 cm/s. The atoms are subsequently slowed down to $\sim 60$ cm/s using an upward slope. The relatively high collision rate (5 s$^{-1}$) allows us to start forced evaporative cooling of the beam, leading to a reduction of the beam temperature by a factor of ~4, and a ten-fold increase of the on-axis phase-space density.Comment: 10 pages, 8 figure

Heat and mass transfer on MHD flow through a porous medium over a stretching surface with heat source

An attempt has been made to study the heat and mass transfer effect on the flow over a stretching sheet in the presence of a heat source. The novelty of the present study is to consider the span wise variation of magnetic field strength, heat source and heat flux. It is also considered the effect of viscous dissipation. The method of solution involves similarity transformation which leads to an exact solution of velocity field. The coupled non-linear and non homogeneous heat equation has been solved by applying Kummer’s function. The non-homogeneity of the heat equation is contributed by the consideration of viscous dissipative energy. KYEWORDS: Heat source, Viscous dissipation, Porous medium, Kummer’s function

New limit for the half-life of double beta decay of 94^{94}Zr to the first excited state of 94^{94}Mo

Neutrinoless Double Beta Decay is a phenomenon of fundamental interest in particle physics. The decay rates of double beta decay transitions to the excited states can provide input for Nuclear Transition Matrix Element calculations for the relevant two neutrino double beta decay process. It can be useful as supplementary information for the calculation of Nuclear Transition Matrix Element for the neutrinoless double beta decay process. In the present work, double beta decay of $^{94}$Zr to the $2^{+}_{1}$ excited state of $^{94}$Mo at 871.1 keV is studied using a low background $\sim$ 230 cm$^3$ HPGe detector. No evidence of this decay was found with a 232 g.y exposure of natural Zirconium. The lower half-life limit obtained for the double beta decay of $\rm^{94}Zr$ to the $2^{+}_{1}$ excited state of $\rm^{94}Mo$ is $T_{1/2} (0\nu + 2\nu)> 3.4 \times 10^{19}$ y at 90% C.L., an improvement by a factor of $\sim$ 4 over the existing experimental limit at 90\% C.L. The sensitivity is estimated to be $T_{1/2} (0\nu + 2\nu) > 2.0\times10^{19}$ y at 90% C.L. using the Feldman-Cousins method.Comment: 11 pages, 7 figures, Accepted in Eur. Phys. J.

High-Q optomechanical circuits made from polished nanocrystalline diamond thin films

We demonstrate integrated optomechanical circuits with high mechanical quality factors prepared from nanocrystalline diamond thin films. Using chemomechanical polishing, the RMS surface roughness of as grown polycrystalline diamond films is reduced below 3nm to allow for the fabrication of high-quality nanophotonic circuits. By integrating free-standing nanomechanical resonators into integrated optical devices, efficient read-out of the thermomechanical motion of diamond resonators is achieved with on-chip Mach-Zehnder interferometers. Mechanical quality factors up to 28,800 are measured for four-fold clamped optomechanical resonators coupled to the evanescent near-field of nanophotonic waveguides. Our platform holds promise for large-scale integration of optomechanical circuits for on-chip metrology and sensing applications

Rotational Bands and Electromagnetic Transitions of some even-even Neodymium Nuclei in J-Projected Hartree-Fock Model

Rotational structures of even-even $^{148-160}$Nd nuclei are studied with the self-consistent deformed Hartree-Fock (HF) and angular momentum (J) projection model. Spectra of ground band, recently observed $K=4^{-}$, $K=5^{-}$ and a few more excited, positive and negative parity bands have been studied upto high spin values. Apart from these detailed electromagnetic properties (like E2, M1 matrix elements) of all the bands have been obtained. There is substantial agreement between our model calculations and available experimental data. Predictions are made about the band structures and electromagnetic properties of these nuclei. Some 4-qasiparticle K-isomeric bands and their electromagnetic properties are predicted.Comment: 20 page