Investigation on Internal Short Circuit Identification of Lithium-Ion Battery Based on Mean-Difference Model and Recursive Least Square Algorithm

Electric vehicles powered by lithium-ion batteries take advantages for urban transportation. However, the safety of lithium-ion battery needs to be improved. Self-induced internal short circuit of lithium-ion batteries is a serious problem which may cause battery thermal runaway. Accurate and fast identification of internal short circuit is critical, while difficult for lithium-ion battery management system. In this study, the influences of the parameters of significance test on the performance of an algorithm for internal short circuit identification are evaluated experimentally. The designed identification is based on the mean-difference model and the recursive least square algorithm. First, the identification method is presented. Then, two characteristic parameters are determined. Subsequently, the parameters of the significance calculation are optimized based on the measured data. Finally, the effectiveness of the method for the early stage internal short circuit detection is studied by an equivalent experiment. The results indicate that the detection time can be shortened significantly via a proper configuration of the parameters for the significance test

Burden of liver cancer due to hepatitis C from 1990 to 2019 at the global, regional, and national levels

BackgroundLiver cancer due to hepatitis C (LCDHC) is one of the leading causes of cancer-related deaths worldwide, and the burden of LCDHC is increasing. We aimed to report the burden of LCDHC at the global, regional, and national levels in 204 countries from 1990 to 2019, stratified by etiology, sex, age, and Sociodemographic Index.MethodsData on LCDHC were available from the Global Burden of Disease, Injuries, and Risk Factors (GBD) study 2019. Numbers and age-standardized mortality, incidence, and disability-adjusted life year (DALY) rates per 100,000 population were estimated through a systematic analysis of modeled data from the GBD 2019 study. The trends in the LCDHC burden were assessed using the annual percentage change.ResultsGlobally, in 2019, there were 152,225 new cases, 141,810 deaths, and 2,878,024 DALYs due to LCDHC. From 1990 to 2019, the number of incidences, mortality, and DALY cases increased by 80.68%, 67.50%, and 37.20%, respectively. However, the age-standardized incidence, mortality, and DALY rate had a decreasing trend during this period. In 2019, the highest age-standardized incidence rates (ASIRs) of LCDHC were found in high-income Asia Pacific, North Africa and the Middle East, and Central Asia. At the regional level, Mongolia, Egypt, and Japan had the three highest ASIRs in 2019. The incidence rates of LCDHC were higher in men and increased with age, with a peak incidence in the 95+ age group for women and the 85–89 age group for men in 2019. A nonlinear association was found between the age-standardized rates of LCDHC and sociodemographic index values at the regional and national levels.ConclusionsAlthough the age-standardized rates of LCDHC have decreased, the absolute numbers of incident cases, deaths, and DALYs have increased, indicating that LCDHC remains a significant global burden. In addition, the burden of LCDHC varies geographically. Male and older adult/s individuals have a higher burden of LCDHC. Our findings provide insight into the global burden trend of LCDHC. Policymakers should establish appropriate methods to achieve the HCV elimination target by 2030 and reducing the burden of LCDHC

Identification and validation of potential diagnostic signature and immune cell infiltration for NAFLD based on cuproptosis-related genes by bioinformatics analysis and machine learning

Background and aimsCuproptosis has been identified as a key player in the development of several diseases. In this study, we investigate the potential role of cuproptosis-related genes in the pathogenesis of nonalcoholic fatty liver disease (NAFLD).MethodThe gene expression profiles of NAFLD were obtained from the Gene Expression Omnibus database. Differential expression of cuproptosis-related genes (CRGs) were determined between NAFLD and normal tissues. Protein–protein interaction, correlation, and function enrichment analyses were performed. Machine learning was used to identify hub genes. Immune infiltration was analyzed in both NAFLD patients and controls. Quantitative real-time PCR was employed to validate the expression of hub genes.ResultsFour datasets containing 115 NAFLD and 106 control samples were included for bioinformatics analysis. Three hub CRGs (NFE2L2, DLD, and POLD1) were identified through the intersection of three machine learning algorithms. The receiver operating characteristic curve was plotted based on these three marker genes, and the area under the curve (AUC) value was 0.704. In the external GSE135251 dataset, the AUC value of the three key genes was as high as 0.970. Further nomogram, decision curve, calibration curve analyses also confirmed the diagnostic predictive efficacy. Gene set enrichment analysis and gene set variation analysis showed these three marker genes involved in multiple pathways that are related to the progression of NAFLD. CIBERSORT and single-sample gene set enrichment analysis indicated that their expression levels in macrophages, mast cells, NK cells, Treg cells, resting dendritic cells, and tumor-infiltrating lymphocytes were higher in NAFLD compared with control liver samples. The ceRNA network demonstrated a complex regulatory relationship between the three hub genes. The mRNA level of these hub genes were further confirmed in a mouse NAFLD liver samples.ConclusionOur study comprehensively demonstrated the relationship between NAFLD and cuproptosis, developed a promising diagnostic model, and provided potential targets for NAFLD treatment and new insights for exploring the mechanism for NAFLD

Global burden of 288 causes of death and life expectancy decomposition in 204 countries and territories and 811 subnational locations, 1990–2021: a systematic analysis for the Global Burden of Disease Study 2021

BACKGROUND Regular, detailed reporting on population health by underlying cause of death is fundamental for public health decision making. Cause-specific estimates of mortality and the subsequent effects on life expectancy worldwide are valuable metrics to gauge progress in reducing mortality rates. These estimates are particularly important following large-scale mortality spikes, such as the COVID-19 pandemic. When systematically analysed, mortality rates and life expectancy allow comparisons of the consequences of causes of death globally and over time, providing a nuanced understanding of the effect of these causes on global populations. METHODS The Global Burden of Diseases, Injuries, and Risk Factors Study (GBD) 2021 cause-of-death analysis estimated mortality and years of life lost (YLLs) from 288 causes of death by age-sex-location-year in 204 countries and territories and 811 subnational locations for each year from 1990 until 2021. The analysis used 56 604 data sources, including data from vital registration and verbal autopsy as well as surveys, censuses, surveillance systems, and cancer registries, among others. As with previous GBD rounds, cause-specific death rates for most causes were estimated using the Cause of Death Ensemble model-a modelling tool developed for GBD to assess the out-of-sample predictive validity of different statistical models and covariate permutations and combine those results to produce cause-specific mortality estimates-with alternative strategies adapted to model causes with insufficient data, substantial changes in reporting over the study period, or unusual epidemiology. YLLs were computed as the product of the number of deaths for each cause-age-sex-location-year and the standard life expectancy at each age. As part of the modelling process, uncertainty intervals (UIs) were generated using the 2·5th and 97·5th percentiles from a 1000-draw distribution for each metric. We decomposed life expectancy by cause of death, location, and year to show cause-specific effects on life expectancy from 1990 to 2021. We also used the coefficient of variation and the fraction of population affected by 90% of deaths to highlight concentrations of mortality. Findings are reported in counts and age-standardised rates. Methodological improvements for cause-of-death estimates in GBD 2021 include the expansion of under-5-years age group to include four new age groups, enhanced methods to account for stochastic variation of sparse data, and the inclusion of COVID-19 and other pandemic-related mortality-which includes excess mortality associated with the pandemic, excluding COVID-19, lower respiratory infections, measles, malaria, and pertussis. For this analysis, 199 new country-years of vital registration cause-of-death data, 5 country-years of surveillance data, 21 country-years of verbal autopsy data, and 94 country-years of other data types were added to those used in previous GBD rounds. FINDINGS The leading causes of age-standardised deaths globally were the same in 2019 as they were in 1990; in descending order, these were, ischaemic heart disease, stroke, chronic obstructive pulmonary disease, and lower respiratory infections. In 2021, however, COVID-19 replaced stroke as the second-leading age-standardised cause of death, with 94·0 deaths (95% UI 89·2-100·0) per 100 000 population. The COVID-19 pandemic shifted the rankings of the leading five causes, lowering stroke to the third-leading and chronic obstructive pulmonary disease to the fourth-leading position. In 2021, the highest age-standardised death rates from COVID-19 occurred in sub-Saharan Africa (271·0 deaths [250·1-290·7] per 100 000 population) and Latin America and the Caribbean (195·4 deaths [182·1-211·4] per 100 000 population). The lowest age-standardised death rates from COVID-19 were in the high-income super-region (48·1 deaths [47·4-48·8] per 100 000 population) and southeast Asia, east Asia, and Oceania (23·2 deaths [16·3-37·2] per 100 000 population). Globally, life expectancy steadily improved between 1990 and 2019 for 18 of the 22 investigated causes. Decomposition of global and regional life expectancy showed the positive effect that reductions in deaths from enteric infections, lower respiratory infections, stroke, and neonatal deaths, among others have contributed to improved survival over the study period. However, a net reduction of 1·6 years occurred in global life expectancy between 2019 and 2021, primarily due to increased death rates from COVID-19 and other pandemic-related mortality. Life expectancy was highly variable between super-regions over the study period, with southeast Asia, east Asia, and Oceania gaining 8·3 years (6·7-9·9) overall, while having the smallest reduction in life expectancy due to COVID-19 (0·4 years). The largest reduction in life expectancy due to COVID-19 occurred in Latin America and the Caribbean (3·6 years). Additionally, 53 of the 288 causes of death were highly concentrated in locations with less than 50% of the global population as of 2021, and these causes of death became progressively more concentrated since 1990, when only 44 causes showed this pattern. The concentration phenomenon is discussed heuristically with respect to enteric and lower respiratory infections, malaria, HIV/AIDS, neonatal disorders, tuberculosis, and measles. INTERPRETATION Long-standing gains in life expectancy and reductions in many of the leading causes of death have been disrupted by the COVID-19 pandemic, the adverse effects of which were spread unevenly among populations. Despite the pandemic, there has been continued progress in combatting several notable causes of death, leading to improved global life expectancy over the study period. Each of the seven GBD super-regions showed an overall improvement from 1990 and 2021, obscuring the negative effect in the years of the pandemic. Additionally, our findings regarding regional variation in causes of death driving increases in life expectancy hold clear policy utility. Analyses of shifting mortality trends reveal that several causes, once widespread globally, are now increasingly concentrated geographically. These changes in mortality concentration, alongside further investigation of changing risks, interventions, and relevant policy, present an important opportunity to deepen our understanding of mortality-reduction strategies. Examining patterns in mortality concentration might reveal areas where successful public health interventions have been implemented. Translating these successes to locations where certain causes of death remain entrenched can inform policies that work to improve life expectancy for people everywhere. FUNDING Bill & Melinda Gates Foundation

Circular RNAs in Gastric Cancer: Potential Biomarkers and Therapeutic Targets

Circular RNAs (circRNAs), as a recently established group of endogenous noncoding RNAs, have been involved in the occurrence and development of different malignancies. Gastric cancer (GC) remains a globally significant contributor to death in cancer patients due to insufficient early diagnosis, limited treatment measures, and poor prognosis. An increasing number of studies have found that many circRNAs are dysregulated in GC and are closely associated with its tumorigenesis and metastasis. Thus, circRNAs have the potential to serve as diagnostic and prognostic biomarkers and even therapeutic targets. This review comprehensively summarizes the most recent findings on how circRNAs influence GC progression and their clinical value. In addition, we present several methological deficiencies in the studies and provide some promising ideas for future research

Construction of a Multifunctional PCM@Catalyst Composite and Its Application in the Fluid Catalytic Cracking Process

Fluid catalytic cracking (FCC) is one of the most important processes in gasoline/diesel oil production, but the strong endothermic effect accompanied by this reaction often results in the deactivation of the catalyst. In this paper, a novel multifunctional phase change material (PCM)@Catalyst composite was designed and constructed, in which the PCM could be used to store waste heat and regulate the temperature for enhancing the catalytic efficiency of the FCC catalyst. Firstly, a core/shell Al-12wt%Si@Al2O3 was prepared via subsequent vapor treatment and high-temperature calcination of an Al-12wt%Si sphere. The Al species in the Al-12wt%Si served as the source of metal ions and was transformed in situ into a well-defined Al2O3 shell, which greatly improved the thermal stability and prevented the leaking of the Al-12wt% Si core in the high-temperature situation. The PCMs@Catalyst composite was then fabricated by casting the mixed powder of Al-12wt%Si@Al2O3 and Y zeolite into a granulated structure. The FCC results demonstrate that Al-12wt%Si@Al2O3/Y zeolite can optimize product distribution and reduce coke yield. This design concept and synthesis strategy can be extended to the production of a wide variety of hierarchical PCM@Catalyst composites for other reactions

Structural Design and Performance Analysis of α Particle Micro-thruster

The α particle propelling is a technology under developing by the author’s research group, which uses α decay isotopes emitting high-speed particles to generate thrust. In this paper we mainly designed the thrust magnitude control and vector control structure suitable for this propelling principle and preliminarily analyzed its control performance. The proposed structure mounts the trust film composed of the decay nuclides onto a quasi-spherical frame surface that is conducive to vector synthesis. The traveling wave type ultrasonic motor drives the diaphragm to control the thrust magnitude of each thrust unit independently and efficiently. The vector control of the joint thrust is implemented by taking advantage of the diversity of combination of multiple thrust units. Theoretical calculation and analysis showed that the thruster structure could achieve the thrust magnitude control accuracy of 0.05µN, and the thrust angle control accuracy of 0.5-1.5 degrees

Thermal performance of PCM and branch-structured fins for cylindrical power battery in a high-temperature environment

Battery modules with phase change material (PCM) cooling inevitably suffer from heat-storage saturation and poor secondary-heat dissipation, especially in high-temperature environments or hot regions. To optimize thermal management, this study firstly explores the thermal behaviors of PCMs with different phase change temperatures (PCTs) in a high-temperature environment. The experimental results show that a PCM with a PCT of 46 °C offers the best cooling effect at a high ambient temperature of 40 °C in this study. For example, the maximum temperature of a cell without PCM reaches 53.3 °C, whereas that of the cell with PCMs having PCTs 40, 46, and 55 °C, are 59.2, 51.6, and 57.5 °C, respectively, during the dynamic cycling process. Nevertheless, the application of above PCM is still unsatisfying because the maximum temperature of the battery in the PCM module exhibits obvious increasing trend with cycles in 40 °C environment. On this basis, several novel fins with multiple heat-flow channels (of V, Y and X shapes) are designed and introduced into the PCM module to enhance the secondary heat dissipation capability. These fins with innovative branch structures deliver excellent performance in alleviating the battery temperature than the traditional rectangular fins, which can be attributed to the ability of the branch structures to increase the heat transfer area by adding heat transfer channels. The results of this work show that the X-shape delivers the best performance in a high-temperature environment of 40 °C by maintaining the maximum temperature of the cell below 47 °C

Three-Dimensional P-wave Velocity Structure of the Zhuxi Ore Deposit, South China Revealed by Control-Source First-Arrival Tomography

The Zhuxi ore deposit, located in Jiangxi province, South China, is the largest tungsten reserve in the world. To better understand the geological structure and distribution of orebodies, we conducted a high resolution three-dimensional P-wave velocity tomography of the uppermost 0.5 km beneath the Zhuxi ore deposit and adjacent area. Our velocity model was derived from 761,653 P-wave first arrivals from 998 control-source shots, recorded by a dense array. As the first 3D P-wave velocity structure of the Zhuxi ore deposit, our model agrees with local topographic and tectonic structures and shows depth-dependent velocity similar to laboratory measurements. The Carboniferous formations hosting the proven orebodies are imaged as high velocities. The high-velocity anomalies extend to a larger area beyond the proven orebodies, and the locations of high–low velocity boundaries are in accordance with the boundaries between the Neoproterozoic formation and the Carboniferous–Triassic formation. Seismic tomography reveals that high-velocity anomalies are closely related to the mineralized areas. Our results are helpful for further evaluating the total reserves and suggest that seismic tomography can be a useful tool for mineral exploration

Three-Dimensional P-wave Velocity Structure of the Zhuxi Ore Deposit, South China Revealed by Control-Source First-Arrival Tomography

The Zhuxi ore deposit, located in Jiangxi province, South China, is the largest tungsten reserve in the world. To better understand the geological structure and distribution of orebodies, we conducted a high resolution three-dimensional P-wave velocity tomography of the uppermost 0.5 km beneath the Zhuxi ore deposit and adjacent area. Our velocity model was derived from 761,653 P-wave first arrivals from 998 control-source shots, recorded by a dense array. As the first 3D P-wave velocity structure of the Zhuxi ore deposit, our model agrees with local topographic and tectonic structures and shows depth-dependent velocity similar to laboratory measurements. The Carboniferous formations hosting the proven orebodies are imaged as high velocities. The high-velocity anomalies extend to a larger area beyond the proven orebodies, and the locations of high–low velocity boundaries are in accordance with the boundaries between the Neoproterozoic formation and the Carboniferous–Triassic formation. Seismic tomography reveals that high-velocity anomalies are closely related to the mineralized areas. Our results are helpful for further evaluating the total reserves and suggest that seismic tomography can be a useful tool for mineral exploration