6 research outputs found
Modelling and Experimental Study of Dissimilar Arc Stud Welding of AISI 304L to AISI 316L Stainless Steel
This paper has aimed to try and establish a successful weld joint between AISI 304L stainless steel as a stud and AISI 316L stainless steel as a plate by using an arc stud welding process. The effect of different current and time welding on the torque results was experimentally studied, by using three-level of each process parameter. The post-weld heat treatment (PWHT) was carried out on the optimum sample of torque, to study the effect of PWHT on mechanical properties (torque and hardness) and microstructure of the welding zone. In the present work, A 3-D finite element model was developed by using ANSYS software version 18 to analyze the influence of time and current welding on the temperature distribution and residual stresses of the resultant welded joints. A transient thermal model was built to predict the temperature distribution whereas the residual stresses were determined by using a static structural model. The PWHT has been used to reduce the amount of residual stresses and enhance the mechanical properties of the welded joint. The micro-hardness based on the Vickers test and the microstructure of welded specimens with and without PWHT have been investigated. The simulation results reveal that the generated temperature and the residual stress is strongly affected by the time and current welding. The mechanical test results indicated that the PWHT prompted an improvement in the hardness values
Modelling and Experimental Study of Dissimilar Arc Stud Welding of AISI 304L to AISI 316L Stainless Steel
This paper has aimed to try and establish a successful weld joint between AISI 304L stainless steel as a stud and AISI 316L stainless steel as a plate by using an arc stud welding process. The effect of different current and time welding on the torque results was experimentally studied, by using three-level of each process parameter. The post-weld heat treatment (PWHT) was carried out on the optimum sample of torque, to study the effect of PWHT on mechanical properties (torque and hardness) and microstructure of the welding zone. In the present work, A 3-D finite element model was developed by using ANSYS software version 18 to analyze the influence of time and current welding on the temperature distribution and residual stresses of the resultant welded joints. A transient thermal model was built to predict the temperature distribution whereas the residual stresses were determined by using a static structural model. The PWHT has been used to reduce the amount of residual stresses and enhance the mechanical properties of the welded joint. The micro-hardness based on the Vickers test and the microstructure of welded specimens with and without PWHT have been investigated. The simulation results reveal that the generated temperature and the residual stress is strongly affected by the time and current welding. The mechanical test results indicated that the PWHT prompted an improvement in the hardness values
Influence of welding parameters of resistance spot welding on joining aluminum with copper
The resistance spot welding (RSW) method was used to join aluminum alloy AA 1050 and copper alloy UNS C50100 sheets. Mechanical properties of the joints were examined. The influence of welding process parameters on tensile shear force of the joints was discussed. The design of experiments (DOE) method was used to analyze the influence of welding parameters on the mechanical properties of the joints. Three RSW parameters were used: welding current, squeeze time, and welding time. The results showed that the joint shear stress increased with increasing the welding current until a value of 12000 Amp. Then the shear stress decreased. The tensile shear stress increased with increasing the welding and squeeze time. As a consequence, it can be possible to weld copper with aluminum by RSW
USING BRASS FOIL INTERLAYER TO IMPROVE THE RESISTANCE SPOT WELDING AA5451 WITH APPLY TAGUCHI METHOD
The aim of this work was to investigate the effect of resistance spot welding (RSW) parameters on the quality of AA5451 joint with brass foil interlayer. Three welding parameters were used; welding current: 12750 and 13500 Amp, electrode pressure: 40 and 45 Bar, welding time: 1.2, 1.4 and 1.6 sec. The squeeze and hold time were kept constant with 1.98 sec for each case. A sheet of AA5451 of 1 mm thickness with brass foil (C26800) of 0.1 mm thickness as interlayer was used. A shear test was used to determine the sheer force of the welded specimen. The results of shear force were analyzed statistically using a Taguchi method with the aid of a Minitab program. The results indicated that the applied pressure and welding current decreased and increased the sheer force of joint respectively. Increasing the welding time decreased and increased the shear force for the intervals 1.2 – 1.4 and 1.4 – 1.6 sec respectively. The presence of the foil increased the shear force of joint by 16 %. The optimum values of parameters that found using the brass foil were; welding current: 13500Amp, electrode pressure: 40Bar, welding time: 1.6sec. A theoretical model of shear force as a function of welding parameters was derived
Joining of carbon steel AISI 1006 to aluminum alloy AA6061-T6 via friction spot joining technique
This work aims to join sheets of carbon steel to aluminum alloy AA6061. A lap joint arrangement was used with a joint lap area of dimensions *25 25 mm . The joining procedure was carried out using a rotating tool of 10 mm shoulder diameter. Three process parameters, with three levels for each parameter, were selected to investigate their effects on joints quality. The parameter’s levels for each experiment were designed using the design of the experiment method (DOE). The results indicated that the two materials were joined by a mechanical interlock at an interface line, without formation of intermetallic compounds. The shear force of the joint reached an ultimate value of .4 82kN . The shear force of the joint improved by increasing plunging depth of the tool. Samples of minimum shear force value failed by a pull-outing aluminum metal from the carbon steel specimen. Samples of higher shear force value exhibited a shear mode of fracture. Increasing the rotating speed and decreasing pre-heating increased the process temperature