10,006 research outputs found
Determinations of upper critical field in continuous Ginzburg-Landau model
Novel procedures to determine the upper critical field have been
proposed within a continuous Ginzburg-Landau model. Unlike conventional
methods, where is obtained through the determination of the smallest
eigenvalue of an appropriate eigen equation, the square of the magnetic field
is treated as eigenvalue problems so that the upper critical field can be
directly deduced. The calculated from the two procedures are
consistent with each other and in reasonably good agreement with existing
theories and experiments. The profile of the order parameter associated with
is found to be Gaussian-like, further validating the methodology
proposed. The convergences of the two procedures are also studied.Comment: Revtex4, 8 pages, 4 figures, references modified, figures and table
embedde
Anomalous thermopower and Nernst effect in : entropy-current loss in precursor state
The heavy-electron superconductor CeCoIn exhibits a puzzling precursor
state above its superconducting critical temperature at = 2.3 K. The
thermopower and Nernst signal are anomalous. Below 15 K, the entropy current of
the electrons undergoes a steep decrease reaching 0 at .
Concurrently, the off-diagonal thermoelectric current is
enhanced. The delicate sensitivity of the zero-entropy state to field implies
phase coherence over large distances. The prominent anomalies in the
thermoelectric current contrast with the relatively weak effects in the
resistivity and magnetization.Comment: 5 figures, 4 page
Improvement of dielectric loss of doped Ba0.5Sr0.5TiO3 thin films for tunable microwave devices
Al2O3-Ba0.5Sr0.5TiO3 (Al2O3-BST) thin films, with different Al2O3 contents,
were deposited on (100) LaAlO3 substrate by pulsed laser deposition (PLD)
technique. The Al2O3-BST films was demosnstrated to be a suitable systems to
fabricate ferroelectric thin films with low dielectric loss and higher figure
of merit for tunable microwave devices. Pure BST thin films were also
fabricated for comparison purpose. The films' structure and morphology were
analyzed by X-ray diffractiopn and scanning electron microscopy, respectively;
nad showed that the surface roughness for the Al2O3-BST films increased with
the Al2O3 content. Apart from that, the broadening in the intensity peak in XRD
result indicating the grain size of the Al2O3-BST films reduced with the
increasing of Al2O3 dopant. We measured the dielctric properties of Al2O3-BST
films with a home-made non-destructive dual resonator method at frequency ~ 7.7
GHZ. The effect of doped Al2O3 into BST thin films significantly reduced the
dielectric constant, dielectric loss and tunability compare to pure BST thin
film. Our result shows the figure of merit (K), used to compare the films with
varied dielectric properties, increased with the Al2O3 content. Therefore
Al2O3-BST films show the potential to be exploited in tunable microwave
devices.Comment: 8 pages, 4 figures, 1 table. Accepted & tentatively for Feb 15 2004
issue, Journal of Applied Physic
Visual Observation and Quantitative Measurement of the Microwave Absorbing Effect at X band
We have setup a simple field mapping measure system to describe graphically
the 2D quasi-free-space electromagnetic wave in a parallel plate waveguide at
the X-band frequencies. Our apparatus illustrates a potential application in
characterizing the microwave absorbing materials. The visual demonstration
about the physical process and quantitative measurement of reflectivity
coefficients can be achieved. This simple apparatus has have an advantage over
with conventional testing methods which usually involve huge, expensive
anechoic chambers and demand samples of large size.Comment: 24 pages, 8 figure
Optimisation of Fine Pitch Contactor and Test Board for QFN Package
Fine pitch contactor describes a contactor with smaller air gap between the contact pins. It is used for testing small portable devices. This work presents the optimised way of designing the 0.4 mm pitch contactor and test board for QFN package. The signal integrity of fine pitch test contactor has become a concern due to the small air-gap between the pins that leads to signal crosstalk and impedance mismatch issues. The same challenge had been seen when designing the fine pitch test board because of the requirement to meet 0.4 mm pitch for typical hand-held devices. It restricts the trace routing with typical design rules at the contactor mounting area due to the limited spaces. This would bring to impedance discontinuity and crosstalk effect. Therefore, optimised design rules on the fine pitch contactor and test board are necessary. Full-wave modelling and system level simulation were demonstrated to study the fine pitch design rules. While the full-wave modelling was to construct the contactor and test board components, the system level simulation was intended to study the signal transmission when propagating from one component to another. Overall, designing the fine pitch contactor requires extra study on the signal integrity and layout design. This paper presents a method to study and design the fine pitch contactor design. It reports the test board to achieve minimum losses and distortion test system for functional testing. Our simulation results for finepitch contactor model show that the return loss is less than 12 dB at 4 GHz
- …