40 research outputs found
A Parametric Numerical Study of Mixing in a Cylindrical Duct
The interaction is described of some of the important parameters affecting the mixing process in a quick mixing region of a rich burn/quick mix/lean burn (RQL) combustor. The performance of the quick mixing region is significantly affected by the geometric designs of both the mixing domain and the jet inlet orifices. Several of the important geometric parameters and operating conditions affecting the mixing process were analytically studied. Parameters such as jet-to-mainstream momentum flux ratio (J), mass flow ratio (MR), orifice geometry, orifice orientation, and number of orifices/row (equally spaced) around the circumferential direction were analyzed. Three different sets of orifice shapes were studied: (1) square, (2) elongated slots, and (3) equilateral triangles. Based on the analytical results, the best mixing configuration depends significantly on the penetration depth of the jet to prevent the hot mainstream flow from being entrained behind the orifice. The structure in a circular mixing section is highly weighted toward the outer wall and any mixing structure affecting this area significantly affects the overall results. The increase in the number of orifices per row increases the mixing at higher J conditions. Higher slot slant angles and aspect ratios are generally the best mixing configurations at higher momentum flux ratio (J) conditions. However, the square and triangular shaped orifices were more effective mixing configurations at lower J conditions
An Analytical Study of Dilution Jet Mixing in a Cylindrical Duct
The mixing performance in a mixing section of a rich burn/quick mix/lean burn (RQL) combustor was calculated using a 3-D numerical model in a non-reacting environment. The numerically calculated results were compared with the measured data reported by Hatch, Sowa, Samuelsen, and Holdeman, 1992. The numerical 3-D temperature fields qualitatively agree with the experimental data. Also, the development of the mixing flow and temperature non-uniformity trends throughout the mixing section for the numerically calculated results quantitatively agree with the measured data. The numerical model predicts less mixing and enhances the temperature gradients as compared to the measured data for the cases reported by Hatch et al. (1992) which include circular and slot orifice shapes (with different slant angles and aspect ratios). The predicted and measured results generally agree in the selection of the slanted slot orifice configuration yielding the best overall mixing performance (based on temperature uniformity) of all the configurations analyzed
Comparison of Mixing Calculations for Reacting and Non-Reacting Flows in a Cylindrical Duct
A production 3-D elliptic flow code has been used to calculate non-reacting and reacting flow fields in an experimental mixing section relevant to a rich burn/quick mix/lean burn (RQL) combustion system. A number of test cases have been run to assess the effects of the variation in the number of orifices, mass flow ratio, and rich-zone equivalence ratio on the flow field and mixing rates. The calculated normalized temperature profiles for the non-reacting flow field agree qualitatively well with the normalized conserved variable isopleths for the reacting flow field indicating that non-reacting mixing experiments are appropriate for screening and ranking potential rapid mixing concepts. For a given set of jet momentum-flux ratio, mass flow ratio, and density ratio (J, MR, and DR), the reacting flow calculations show a reduced level of mixing compared to the non-reacting cases. In addition, the rich-zone equivalence ratio has noticeable effect on the mixing flow characteristics for reacting flows
The ABC130 barrel module prototyping programme for the ATLAS strip tracker
For the Phase-II Upgrade of the ATLAS Detector, its Inner Detector,
consisting of silicon pixel, silicon strip and transition radiation
sub-detectors, will be replaced with an all new 100 % silicon tracker, composed
of a pixel tracker at inner radii and a strip tracker at outer radii. The
future ATLAS strip tracker will include 11,000 silicon sensor modules in the
central region (barrel) and 7,000 modules in the forward region (end-caps),
which are foreseen to be constructed over a period of 3.5 years. The
construction of each module consists of a series of assembly and quality
control steps, which were engineered to be identical for all production sites.
In order to develop the tooling and procedures for assembly and testing of
these modules, two series of major prototyping programs were conducted: an
early program using readout chips designed using a 250 nm fabrication process
(ABCN-25) and a subsequent program using a follow-up chip set made using 130 nm
processing (ABC130 and HCC130 chips). This second generation of readout chips
was used for an extensive prototyping program that produced around 100
barrel-type modules and contributed significantly to the development of the
final module layout. This paper gives an overview of the components used in
ABC130 barrel modules, their assembly procedure and findings resulting from
their tests.Comment: 82 pages, 66 figure