Design overview of high pressure dense phase CO2 pipeline transport in flow mode

In open literature, there is little information available with regards to the engineering and technological issues for material corrosion, in relation to high pressure supercritical CO2 pipeline transport from single point sources, such as the power industry. A typical CO2 pipeline is designed to operate at high pressure in the dense phase. However, it is evident that although there is considerable experience of testing materials in lower pressure gaseous CO2 in the oil and gas industry, there is little understanding of the behaviour of pipeline materials when in contact with impure CO2 captured either from power plants or the oil and gas industry. In this particular project development, a dynamic dense phase CO2 corrosion rig has been built (conditions: ∼85 bar, 40 °C and up to 5 l/min flow rate) in flow mode, to understand the effect of impurities (SO2, O2, H2, NO2 & CO) present in captured CO2 on the pipeline transport materials. This unique facility in the UK was developed via the MATTRANS project funded by the E.ON-EPSRC strategic partnership (EP/G061955/1). The test rig includes different metallic materials (X grade steel: X60, X70 and X100) to assess the corrosion of pipelines, and different geometry components (tubes, plates, charpy and tensile coupons), to assess ageing and decompression behavior of polymeric seals (Neoprene, fluorocarbon, ethylene and Buna N) under water-saturated dense phase CO2 with different impurity concentrations (0.05 mol % SO2; 4 mol % O2; 2 mol % H2; 0.05 mol % NO2; 1 mol % CO). The dynamic data generated from this dense phase CO2 corrosion rig will give vital information with regards to pipeline suitability and lifetimes, when operating with dense CO2

Engineering scale-up challenges, and effects of SO2 on the calcium looping cycle for post combustion CO2 capture

Engineering scale-up challenges, and potential effects of SO2 on the calcium looping cycle for post combustion CO2 capture have been investigated in Cranfield University's pilot scale reactor (25 kWth). Following reactor and process modifications, close to 80% capture was achieved. SO2 was found to have a detrimental effect on the calcium looping cycle in both batch and continuous cyclic tests, although the presence of steam from natural gas-fired burners was found to have a positive effect on maintaining capture capacity of the sorbent

Pressurised calcination-atmospheric carbonation of limestone for cyclic CO2 capture from flue gases

A study was carried out to investigate the CO2 capture performance of limestone under atmospheric carbonations following pressurised calcination. A series of tests was carried out to study the role of pressurised calcination using a fluidised bed reactor. In this investigation, calcination of limestone particles was carried out at three levels of pressure: 0.1 MPa, 0.5 MPa, and 1.0 MPa. After calcination, the capture performance of the calcined sorbent was tested at atmospheric pressure. As expected, the results indicate that the carbonation conversion of calcined sorbent decreases as the pressure is increased during calcination. Pressurised calcination requires higher temperatures and causes an increase in sorbent sintering, albeit that it would have the advantage of reducing equipment size as well as the compression energy necessary for CO2transport and storage, and an analysis has been provided to give an assessment of the potential benefits associated with such an option using process software.EPSR

Microfluidic encapsulation of Xenopus laevis cell-free extracts using hydrogel photolithography

© The Author(s), 2020. This article is distributed under the terms of the Creative Commons Attribution License. The definitive version was published in Geisterfer, Z. M., Oakey, J., & Gatlin, J. C. . Microfluidic encapsulation of Xenopus laevis cell-free extracts using hydrogel photolithography. STAR Protocols, 1(3), (2020): 100221, doi:10.1016/j.xpro.2020.100221.Cell-free extract derived from the eggs of the African clawed frog Xenopus laevis is a well-established model system that has been used historically in bulk aliquots. Here, we describe a microfluidic approach for isolating discrete, biologically relevant volumes of cell-free extract, with more expansive and precise control of extract shape compared with extract-oil emulsions. This approach is useful for investigating the mechanics of intracellular processes affected by cell geometry or cytoplasmic volume, including organelle scaling and positioning mechanisms. For complete details on the use and execution of this protocol, please refer to Geisterfer et al. (2020).This work was made possible by an Institutional Development Award (IDeA) from the National Institute of General Medical Sciences of the National Institutes of Health under grant no. 2P20GM103432. It was also supported by additional funding provided by the NIGMS under grant no. R01GM113028, the NSF Faculty CAREER Program under award no. BBBE 1254608, Whitman Center fellowships at the Marine Biological Laboratory, and the Biomedical Scholars program of the Pew Charitable Trusts. We thank Drs. Aaron Groen and Tim Mitchison for their intellectual contributions and involvement in some of the pioneering experiments that set the foundation for this approach

Fate of nitrogen/trace metals species during combustion and gasification of biomass

This thesis focused on the fate of nitrogen and trace metals species from combustion and gasification of biomass. The effect of process parameters on the release of these species during pilot-scale combustion and gasification of biomass was investigated and the information used to identify methods for the reduction of these species. The investigation focused on Miscanthus and Dried distillers’ grains with solubles (DDGS). The pilot-scale test rigs used were a fluidised-bed combustor and a fixed-bed downdraft gasifier. The two fuels were analysed by means of proximate, ultimate and ash analysis. The process parameters monitored were temperatures, gas flow, gas composition and ash composition and the process parameters studied are bed temperature and equivalence ratio. The different nitrogen content of the two fuels plays an important role in the emission. Both bed temperature and air to fuel ratio have demonstrated to have an important influence in the release of nitrogen oxides in combustion and ammonia in gasification, therefore they can be used to mitigate the emission of these species in the flue gas. Both processes are affected by the high alkali metals content of the fuels for the tendency to form low melting composites. Differences have been highlighted in the metal distribution between combustion and gasification. The different nitrogen and ash content of the two fuels make the results of the present thesis applicable to predict the behaviour of other biomass fuels according to the fuel characteristics. The scale of the tests performed allowed highlighting which methods can be used to control the emission of nitrogen and trace metal species. Moreover, the investigation highlighted major drawbacks in the use of biomass fuels in both fluidised bed and fixed bed technology due to ash properties.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Staged inertial microfluidic focusing for complex fluid enrichment

Microfluidic inertial focusing reliably and passively aligns small particles and cells through a combination of competing inertial fluid forces. The equilibrium behavior of inertially focused particles in straight channels has been extensively characterized and has been shown to be a strong function of channel size, geometry and particle size. We demonstrate that channels of varying geometry may be combined to produce a staged device capable of high throughput particle and cell concentration and efficient single pass complex fluid enrichment. Straight and asymmetrically curved microchannels were combined in series to accelerate focusing dynamics and improve concentration efficiency. We have investigated single and multiple pass concentration efficiency and results indicate that these devices are appropriate for routine cell handling operations, including buffer exchange. We demonstrate the utility of these devices by performing a ubiquitous fluorescence staining assay on-chip while sacrificing very little sample or processing time relative to centrifugation. Staged concentration is particularly desirable for point of care settings in which more conventional instrumentation is impractical or cost-prohibitive.United States. Department of Defense (Congressionally Directed Medical Research Program, Prostate Cancer Research Program Award number W81XWH-13-1-0272)University of Wyoming. IDeA Networks of Biomedical Research Excellence (program P20RR016474)University of Wyoming. IDeA Networks of Biomedical Research Excellence (program P20GM103432)United States. Department of Defense (Congressionally Directed Medical Research Program, Prostate Cancer Research Program Award number W81XWH-13-1-0273)United States. National Aeronautics and Space Administration (Wyoming NASA Space Grant Consortium (NASA Grant #NNX10A095H))National Science Foundation (U.S.) (Wyoming Experimental Program to Stimulate Competitive Research (Grant EPS-0447681)

Enhancing properties of iron and manganese ores as oxygen carriers for chemical looping processes by dry impregnation

The use of naturally occurring ores as oxygen carriers in CLC processes is attractive because of their relative abundance and low cost. Unfortunately, they typically exhibit lower reactivity and lack the mechanical robustness required, when compared to synthetically produced carriers. Impregnation is a suitable method for enhancing both the reactivity and durability of natural ores when used as oxygen carriers for CLC systems. This investigation uses impregnation to improve the chemical and mechanical properties of a Brazilian manganese ore and a Canadian iron ore. The manganese ore was impregnated with Fe2O3 and the iron ore was impregnated with Mn2O3 with the goal of forming a combined Fe/Mn oxygen carrier. The impregnated ore’s physical characteristics were assessed by SEM, BET and XRD analysis. Measurements of the attrition resistance and crushing strength were used to investigate the mechanical robustness of the oxygen carriers. The impregnated ore’s mechanical and physical properties were clearly enhanced by the impregnation method, with boosts in crushing strength of 11–26% and attrition resistance of 37–31% for the impregnated iron and manganese ores, respectively. Both the unmodified and impregnated ore’s reactivity, for the conversion of gaseous fuel (CH4 and syngas) and gaseous oxygen release (CLOU potential) were investigated using a bench-scale quartz fluidised-bed reactor. The impregnated iron ore exhibited a greater degree of syngas conversion compared to the other samples examined. Iron ore based oxygen carrier’s syngas conversion increases with the number of oxidation and reduction cycles performed. The impregnated iron ore exhibited gaseous oxygen release over extended periods in an inert atmosphere and remained at a constant 0.2% O2 concentration by volume at the end of this inert period. This oxygen release would help ensure the efficient use of solid fuels. The impregnated iron ore’s reactivity for CH4 conversion was similar to the reactivity of its unmodified counterpart. The unmodified manganese ore converted CH4 to the greatest extent of all the samples tested here, while the impregnated manganese ore exhibited a decrease in reactivity with respect to syngas and CH4 conversion.EPSR