Effect of morphology and hydrophobization of MoS2 microparticles on the stability of poly-α-olefins lubricants

International audienceThe use of MoS ⁠ 2 nanoparticles as additive to lubricating oils is restricted by their low stability in oily media, which limits their use despite the enormous benefits associated with their intrinsic properties in terms of reduction of friction and wear coefficients. In this context, we investigated the effect of morphologies (platelets vs spheres) and surface functionalization of nanoparticles on the stability of their suspensions in poly-α-olefins (PAO) with various viscosities, which are base oils used in wind turbines. The particles were characterized by XRD, FTIR, scanning electron microscopy, atomic force microscopy and dynamic light scattering, and the stability of the resultant formulations was followed by optical (non-contact) measurements. It was found that the dispersions had similar stability despite the larger size of platelet-like particles compared to spherical ones (1-5 μm vs 600-800 nm). The dispersibility could be increased through grafting of alkylsilane on the surface defects (the longer the alkyl chain, the more stable the formulation) and with the increase of the oil kinematic viscosity (from 34 to 1705 cps at 25 °C)

A Portuguese East Indiaman from the 1502-1503 Fleet of Vasco da Gama off Al Hallaniyah Island, Oman: An interim report

Two Portuguese naus from Vasco da Gama's second voyage to India, left behind to disrupt maritime trade between India and the Red Sea, were wrecked in May 1503 off the north-eastern coast of Al Hallaniyah Island, Oman. The ships, Esmeralda and São Pedro, had been commanded by da Gama's maternal uncles, Vicente and Brás Sodré, respectively. A detailed study and scientific analysis of an artefact assemblage recovered during archaeological excavations conducted in Al Hallaniyah in 2013 and 2014 confirms the location of an early 16th-century Portuguese wreck-site, initially discovered in 1998. Esmeralda is proposed as the probable source of the remaining, un-salved wreckage

Melt infiltration for the preparation of finely dispersed Ni-FeOx nanoparticles on SBA-15 for the hydrodeoxygenation of m-cresol

International audienceThe polymer-assisted melting infiltration method was used to finely disperse Ni, Fe and bimetallic Ni-Fe precursors in ordered mesoporous SBA-15 support. This approach allowed to obtain small Ni nanoparticles, in the order of 2 nm in size, with finely dispersed iron oxide surrounding metallic Ni, without evidence of Ni-Fe alloy formation. The catalysts were used in the HDO reaction of m-cresol at 300 °C and atmospheric pressure. The conversion of m-cresol was found to be dependent on Ni content, with the total reaction rate decreasing when Ni is partially replaced by iron. Toluene was the main product obtained for both, mono Ni and bimetallic Ni-Fe catalysts, thus suggesting that nickel nanoparticles when in the form of small sized particles, are the active sites for deoxygenation, independent on the presence of oxophilic iron site in their proximity. Such findings will serve for the further design of effective catalysts for the upgrading of lignin-derived bio-oil

Isocyanate-mediated covalent immobilization of Mucor miehei lipase onto SBA-15 for transesterification reaction

International audienceMucor miehei lipase (Mm-L) covalently bind on a hexagonally ordered silica SBA-15 (Santa Barbara Amorphous), previously functionalizecl with isocyanate moieties, was examined as biocatalyst for transesterification of colza oil wills methanol. The isocyanate-mesoporous silica (NCO-SBA-15) was obtained by condensation of silanol with triethoxysilane propyl isocyanate (TPI). The efficiency of the functionalization has been evidenced by infrared, Si-29 and C-13 NMR spectroscopies. The substrate provided a moderate hydrophobic microenvironment together with reactive sites for chemical immobilization of the enzyme. The biocatalyst containing 0.28 g of Mm-L per gram of support afforded a high level of transesterification activity (yield up to 80%) while using 1:1 molar ratio of methanol/colza oil and small amount of water. The biocatalyst showed higher operational stability than the corresponding physisorbed enzyme since it can be reused 6 times against 2 consecutive runs for the physisorbed enzyme