Electrical characteristics of B-GaN2O3 thin films grown by PEALD

Cataloged from PDF version of article.In this work, 7.5 nm Ga2O3 dielectric thin films have been deposited on p-type (111) silicon wafer using plasma enhanced atomic layer deposition (PEALD) technique. After the deposition, Ga2O3 thin films were annealed under N-2 ambient at 600, 700, and 800 degrees C to obtain beta-phase. The structure and microstructure of the beta-Ga2O3 thin films was carried out by using grazing-incidence X-ray diffraction (GIXRD). To show effect of annealing temperature on the microstructure of beta-Ga2O3 thin films, average crystallite size was obtained from the full width at half maximum (FWHM) of Bragg lines using the Scherrer formula. It was found that crystallite size increased with increasing annealing temperature and changed from 0.8 nm to 9.1 nm with annealing. In order to perform electrical characterization on the deposited films, Al/beta-Ga2O3/p-Si metal-oxide-semiconductor (MOS) type Schottky barrier diodes (SBDs) were fabricated using the beta-Ga2O3 thin films were annealed at 800 degrees C. The main electrical parameters such as leakage current level, reverse breakdown voltage, series resistance (R-S), ideality factor (n), zero-bias barrier height (phi(Bo)), and interface states (N-SS) were obtained from the current-voltage (I-V) and capacitance-voltage (C-V) measurements at room temperature. The RS values were calculated by using Cheung methods. The energy density distribution profile of the interface states as a function of (E-SS-E-V) was obtained from the forward bias I-V measurements by taking bias dependence of ideality factor, effective barrier height (phi(e)), and R-S into account. Also using the Norde function and C-V technique, phi(e) values were calculated and cross-checked. Results show that beta-Ga2O3 thin films deposited by PEALD technique at low temperatures can be used as oxide layer for MOS devices and electrical properties of these devices are influenced by some important parameters such as NSS, RS, and beta-Ga2O3 oxide layer. (C) 2014 Elsevier B.V. All rights reserved

Effect of post-deposition annealing on the electrical properties of B-Ga2O3 thin films grown on p-Si by plasma-enhanced atomic layer deposition

Cataloged from PDF version of article.Ga2O3 dielectric thin films were deposited on (111)-oriented p-type silicon wafers by plasma-enhanced atomic layer deposition using trimethylgallium and oxygen plasma. Structural analysis of the Ga 2O3 thin films was carried out using grazing-incidence x-ray diffraction. As-deposited films were amorphous. Upon postdeposition annealing at 700, 800, and 900°C for 30min under N2 ambient, films crystallized into β-form monoclinic structure. Electrical properties of the β-Ga2O3 thin films were then investigated by fabricating and characterizing Al/β-Ga2O3/p-Si metal-oxide-semiconductor capacitors. The effect of postdeposition annealing on the leakage current densities, leakage current conduction mechanisms, dielectric constants, flat-band voltages, reverse breakdown voltages, threshold voltages, and effective oxide charges of the capacitors were presented. The effective oxide charges (Qeff) were calculated from the capacitance-voltage (C-V) curves using the flat-band voltage shift and were found as 2.6×1012, 1.9×1012, and 2.5×10 12 cm-2 for samples annealed at 700, 800, and 900°C, respectively. Effective dielectric constants of the films decreased with increasing annealing temperature. This situation was attributed to the formation of an interfacial SiO2 layer during annealing process. Leakage mechanisms in the regions where current increases gradually with voltage were well fitted by the Schottky emission model for films annealed at 700 and 900°C, and by the Frenkel-Poole emission model for film annealed at 800°C. Leakage current density was found to improve with annealing temperature. β-Ga2O3 thin film annealed at 800°C exhibited the highest reverse breakdown field value. © 2014 American Vacuum Society

Measurements of the Rate Capability of Various Resistive Plate Chambers

Resistive Plate Chambers (RPCs) exhibit a significant loss of efficiency for the detection of particles, when subjected to high particle fluxes. This rate limitation is related to the usually high resistivity of the resistive plates used in their construction. This paper reports on measurements of the performance of three different glass RPC designs featuring a different total resistance of the resistive plates. The measurements were performed with 120 GeV protons at varying beam intensitie

Surface-decorated ZnO nanoparticles and ZnO nanocoating on electrospun polymeric nanofibers by atomic layer deposition for flexible photocatalytic nanofibrous membranes

Cataloged from PDF version of article.Electrospun polymeric nanofibers were either surface-decorated with zinc oxide (ZnO) nanoparticles or coated with a continuous ZnO thin film with a precise thickness (similar to 27 nm) via atomic layer deposition (ALD) for the fabrication of flexible photocatalytic nanofibrous membranes

Optical characteristics of nanocrystalline AlxGa1-xN thin films deposited by hollow cathode plasma-assisted atomic layer deposition

Cataloged from PDF version of article.Gallium nitride (GaN), aluminum nitride (AlN), and AlxGa(1-x)N films have been deposited by hollow cathode plasma-assisted atomic layer deposition at 200 degrees C on c-plane sapphire and Si substrates. The dependence of film structure, absorption edge, and refractive index on postdeposition annealing were examined by x-ray diffraction, spectrophotometry, and spectroscopic ellipsometry measurements, respectively. Well-adhered, uniform, and polycrystalline wurtzite (hexagonal) GaN, AlN, and AlxGa1-xN films were prepared at low deposition temperature. As revealed by the x-ray diffraction analyses, crystallite sizes of the films were between 11.7 and 25.2 nm. The crystallite size of as-deposited GaN film increased from 11.7 to 12.1 and 14.4 nm when the annealing duration increased from 30 min to 2 h (800 degrees C). For all films, the average optical transmission was similar to 85% in the visible (VIS) and near infrared spectrum. The refractive indices of AlN and AlxGa1-xN were lower compared to GaN thin films. The refractive index of as-deposited films decreased from 2.33 to 2.02 (lambda = 550 nm) with the increased Al content x (0 400 nm). Postdeposition annealing at 900 degrees C for 2 h considerably lowered the refractive index value of GaN films (2.33-1.92), indicating a significant phase change. The optical bandgap of as-deposited GaN film was found to be 3.95 eV, and it decreased to 3.90 eV for films annealed at 800 degrees C for 30 min and 2 h. On the other hand, this value increased to 4.1 eV for GaN films annealed at 900 degrees C for 2 h. This might be caused by Ga2O3 formation and following phase change. The optical bandgap value of as-deposited AlxGa1-xN films decreased from 5.75 to 5.25 eV when the x values decreased from 1 to 0.68. Furthermore, postdeposition annealing did not affect the bandgap of Al-rich films. (C) 2014 American Vacuum Society

Hollow cathode plasma-assisted atomic layer deposition of crystalline AIN, GaN and AI Ga1- N thin films at low temperatures

Cataloged from PDF version of article.The authors report on the use of hollow cathode plasma for low-temperature plasma-assisted atomic layer deposition (PA-ALD) of crystalline AlN, GaN and AlxGa1 xN thin films with low impurity concentrations. Depositions were carried out at 200 C using trimethylmetal precursors and NH3 or N2/H2 plasma. X-ray photoelectron spectroscopy showed the presence of 2.5–3 at.% O in AlN and 1.5–1.7 at.% O in GaN films deposited using NH3 and N2/H2 plasma, respectively. No C impurities were detected within the films. Secondary ion mass spectroscopy analyses performed on the films deposited using NH3 plasma revealed the presence of O, C (both <1 at.%), and H impurities. GIXRD patterns indicated polycrystalline thin films with wurtzite crystal structure. Hollow cathode PA-ALD parameters were optimized for AlN and GaN thin films using N2/H2 plasma. Trimethylmetal and N2/H2 saturation curves evidenced the selflimiting growth of AlN and GaN at 200 C. AlN exhibited linear growth with a growth per cycle (GPC) of 1.0 A. For GaN, the GPC decreased with the increasing number of deposition cycles, indicating ˚ substrate-enhanced growth. The GPC calculated from a 900-cycle GaN deposition was 0.22 A. ˚ Ellipsometric spectra of the samples were modeled using the Cauchy dispersion function, from which the refractive indices of 59.2 nm thick AlN and 20.1 nm thick GaN thin films were determined to be 1.94 and 2.17 at 632 nm, respectively. Spectral transmission measurements of AlN, GaN and AlxGa1 xN thin films grown on double side polished sapphire substrates revealed near-ideal visible transparency with minimal absorption. Optical band edge values of the AlxGa1 xN films shifted to lower wavelengths with the increasing Al content, indicating the tunability of band edge values with the alloy composition

Template-based synthesis of aluminum nitride hollow Nanofibers via plasma-enhanced atomic layer deposition

Cataloged from PDF version of article.Aluminum nitride (AlN) hollow nanofibers were synthesized via plasma-enhanced atomic layer deposition using sacrificial electrospun polymeric nanofiber templates having different average fiber diameters (~70, ~330, and ~740 nm). Depositions were carried out at 200°C using trimethylaluminum and ammonia precursors. AlN-coated nanofibers were calcined subsequently at 500°C for 2 h to remove the sacrificial polymeric nanofiber template. SEM studies have shown that there is a critical wall thickness value depending on the template's average fiber diameter for AlN hollow nanofibers to preserve their shapes after the template has been removed by calcination. Best morphologies were observed for AlN hollow nanofibers prepared by depositing 800 cycles (corresponding to ~69 nm) on nanofiber templates having ~330 nm average fiber diameter. TEM images indicated uniform wall thicknesses of ~65 nm along the fiber axes for samples prepared using templates having ~70 and ~330 nm average fiber diameters. Synthesized AlN hollow nanofibers were polycrystalline with a hexagonal crystal structure as determined by high-resolution TEM and selected area electron diffraction. Chemical compositions of coated and calcined samples were studied using X-ray photoelectron spectroscopy (XPS). High-resolution XPS spectra confirmed the presence of AlN. © 2012 The American Ceramic Societ

Polymer-inorganic core-shell nanofibers by electrospinning and atomic layer deposition: flexible nylon-znO core-shell nanofiber mats and their photocatalytic activity

Cataloged from PDF version of article.Polymer-inorganic core-shell nanofibers were produced by two-step approach; electrospinning and atomic layer deposition (ALD). First, nylon 6,6 (polymeric core) nanofibers were obtained by electrospinning, and then zinc oxide (ZnO) (inorganic shell) with precise thickness control was deposited onto electrospun nylon 6,6 nanofibers using ALD technique. The bead-free and uniform nylon 6,6 nanofibers having different average fiber diameters (∼80, ∼240 and ∼650 nm) were achieved by using two different solvent systems and polymer concentrations. ZnO layer about 90 nm, having uniform thickness around the fiber structure, was successfully deposited onto the nylon 6,6 nanofibers. Because of the low deposition temperature utilized (200 °C), ALD process did not deform the polymeric fiber structure, and highly conformal ZnO layer with precise thickness and composition over a large scale were accomplished regardless of the differences in fiber diameters. ZnO shell layer was found to have a polycrystalline nature with hexagonal wurtzite structure. The core-shell nylon 6,6-ZnO nanofiber mats were flexible because of the polymeric core component. Photocatalytic activity of the core-shell nylon 6,6-ZnO nanofiber mats were tested by following the photocatalytic decomposition of rhodamine-B dye. The nylon 6,6-ZnO nanofiber mat, having thinner fiber diameter, has shown better photocatalytic efficiency due to higher surface area of this sample. These nylon 6,6-ZnO nanofiber mats have also shown structural stability and kept their photocatalytic activity for the second cycle test. Our findings suggest that core-shell nylon 6,6-ZnO nanofiber mat can be a very good candidate as a filter material for water purification and organic waste treatment because of their photocatalytic properties along with structural flexibility and stability. © 2012 American Chemical Society

Low-Temperature Deposition of Hexagonal Boron Nitride via Sequential Injection of Triethylboron and N2/H2 Plasma

Cataloged from PDF version of article.Hexagonal boron nitride (hBN) thin films were deposited on silicon and quartz substrates using sequential exposures of triethylboron and N 2 /H 2 plasma in a hollow-cathode plasma- assisted atomic layer deposition reactor at low temperatures ( ≤ 450 ° C). A non-saturating film deposition rate was observed for substrate temperatures above 250 ° C. BN films were charac- terized for their chemical composition, crystallinity, surface morphology, and optical properties. X-ray photoelectron spec- troscopy (XPS) depicted the peaks of boron, nitrogen, carbon, and oxygen at the film surface. B 1s and N 1s high-resolution XPS spectra confirmed the presence of BN with peaks located at 190.8 and 398.3 eV, respectively. As deposited films were polycrystalline, single-phase hBN irrespective of the deposition temperature. Absorption spectra exhibited an optical band edge at ~ 5.25 eV and an optical transmittance greater than 90% in the visible region of the spectrum. Refractive index of the hBN film deposited at 450 ° C was 1.60 at 550 nm, which increased to 1.64 after postdeposition annealing at 800 ° C for 30 min. These results represent the first demonstration of hBN deposi- tion using low-temperature hollow-cathode plasma-assisted sequential deposition technique. © 2014 The American Ceramic Society

Metal-semiconductor-metal ultraviolet photodetectors based on gallium nitride grown by atomic layer deposition at low temperatures

Cataloged from PDF version of article.Proof-of-concept, first metal-semiconductor-metal ultraviolet photodetectors based on nanocrystalline gallium nitride (GaN) layers grown by low-temperature hollow-cathode plasma-assisted atomic layer deposition are demonstrated. Electrical and optical characteristics of the fabricated devices are investigated. Dark current values as low as 14 pA at a 30 V reverse bias are obtained. Fabricated devices exhibit a 15× UV/VIS rejection ratio based on photoresponsivity values at 200 nm (UV) and 390 nm (VIS) wavelengths. These devices can offer a promising alternative for flexible optoelectronics and the complementary metal oxide semiconductor integration of such devices. © 2014 Society of Photo-Optical Instrumentation Engineers (SPIE)