1,036 research outputs found
First principles study of adsorbed Cu_n (n=1-4) microclusters on MgO(100): structural and electronic properties
We present a density functional study of the structural and electronic
properties of small Cu_n (n=1,4) aggregates on defect-free MgO(100). The
calculations employ a slab geometry with periodic boundary conditions,
supercells with up to 76 atoms, and include full relaxation of the surface
layer and of all adsorbed atoms. The preferred adsorption site for a single Cu
adatom is on top of an oxygen atom. The adsorption energy and Cu-O distance are
E_S-A = 0.99 eV and d_S-A = 2.04 Angstroems using the Perdew-Wang gradient
corrected exchange correlation functional. The saddle point for surface
diffusion is at the "hollow" site, with a diffusion barrier of around 0.45 eV.
For the adsorbed copper dimer, two geometries, one parallel and one
perpendicular to the surface, are very close in energy. For the adsorbed Cu_3,
a linear configuration is preferred to the triangular geometry. As for the
tetramer, the most stable adsorbed geometry for Cu_4 is a rhombus. The
adsorption energy per Cu atom decreases with increasing the size of the
cluster, while the Cu-Cu cohesive energy increases, rapidly becoming more
important than the adsorption energy.Comment: Major revision, Latex(2e) document, 23 pages, 11 figures, accepted
for publication in J. of Chem. Phys., paper available at
http://irrmawww.epfl.ch/vm/vm_wor
Real Analyticity of Periodic Layer Potentials Upon Perturbation of the Periodicity Parameters and of the Support
We prove that the periodic layer potentials for the Laplace operator depend real analytically on the density function, on the supporting hypersurface, and on the periodicity parameters
Existence results for a nonlinear nonautonomous transmission problem via domain perturbation
In this paper we study the existence and the analytic dependence upon domain perturbation of the solutions of a nonlinear nonautonomous transmission problem for the Laplace equation. The problem is defined in a pair of sets consisting of a perforated domain and an inclusion whose shape is determined by a suitable diffeomorphism. First we analyse the case in which the inclusion is a fixed domain. Then we will perturb the inclusion and study the arising boundary value problem and the dependence of a specific family of solutions upon the perturbation parameter
Numerical 3D simulation of a full system air core compulsator-electromagnetic rail launcher
Multiphysics problems represent an open issue in numerical modeling. Electromagnetic launchers represent typical examples that require a strongly coupled magnetoquasistatic and mechanical approach. This is mainly due to the high velocities which make comparable the electrical and the mechanical response times. The analysis of interacting devices (e.g., a rail launcher and its feeding generator) adds further complexity, since in this context the substitution of one device with an electric circuit does not guarantee the accuracy of the analysis. A simultaneous full 3D electromechanical analysis of the interacting devices is often required. In this paper a numerical 3D analysis of a full launch system, composed by an air-core compulsator which feeds an electromagnetic rail launcher, is presented. The analysis has been performed by using a dedicated, in-house developed research code, named "EN4EM" (Equivalent Network for Electromagnetic Modeling). This code is able to take into account all the relevant electromechanical quantities and phenomena (i.e., eddy currents, velocity skin effect, sliding contacts) in both the devices. A weakly coupled analysis, based on the use of a zero-dimensional model of the launcher (i.e., a single loop electrical equivalent circuit), has been also performed. Its results, compared with those by the simultaneous 3D analysis of interacting devices, show an over-estimate of about 10-15% of the muzzle speed of the armature
Null-Flux Coils in Permanent Magnets Bearings
In this paper, the stability analysis of a new permanent magnets (PMs) bearings is presented and discussed. The suspension is assured by the repulsive force of properly shaped PMs placed on both the stator and the rotor. Then, exploiting currents induced on a system of null-flux coils attached to the stator, a stabilizing force for the translation of the center of mass of the rotor is obtained. The performance of the proposed bearing is investigated by a research code, previously developed at DESTEC and capable to simulate six degrees of freedom electromechanical devices
Dependence of effective properties upon regular perturbations
In this survey, we present some results on the behavior of effective properties in presence of perturbations of the geometric and physical parameters. We first consider the case of a Newtonian fluid flowing at low Reynolds numbers around a periodic array of cylinders. We show the results of [43], where it is proven that the average longitudinal flow depends real analytically upon perturbations of the periodicity structure and the cross section of the cylinders. Next, we turn to the effective conductivity of a periodic two-phase composite with ideal contact at the interface. The composite is obtained by introducing a periodic set of inclusions into an infinite homogeneous matrix made of a different material. We show a result of [41] on the real analytic dependence of the effective conductivity upon perturbations of the shape of the inclusions, the periodicity structure, and the conductivity of each material. In the last part of the chapter, we extend the result of [41] to the case of a periodic two-phase composite with imperfect contact at the interface
Comparison of flood hazard assessment criteria for pedestrians with a refined mechanics-based method
Floods have caused severe destruction and affected communities in different ways throughout history. Flood events are being exacerbated by climate change and hence it is increasingly necessary to have a more accurate understanding of various aspects of flood hazard, particularly for pedestrians. The focus of this study is therefore to investigate different criteria to assess the flood hazard for pedestrians and to propose improvements in assessing such hazards. The revised mechanics-based approach reported herein gives results based on a full physical analysis of the forces acting on a body and can be universally applied as the method can be fine-tuned for different region of the world. The results from flood hazard assessments can be used to: design evacuation plans, improve resilience of sites prone to flooding and plan more resilient future developments. Extreme flood events in the UK and documented for Boscastle (2004) and Borth (2012) were used as case studies. Two approaches were considered, including: (i) a mechanics-based approach, and (ii) an experimental-based approach, with the criteria for the stability of pedestrians in floods being compared for the criteria used by regulatory authorities in Australia, Spain, UK and USA. The results obtained in this study demonstrate that the mechanics-based methods are preferable in determining flood hazard rating assessments
- …