Airframe noise of the DC-9-31

Airframe noise measurements are reported for the DC-9-31 aircraft flown at several speeds and with a number of flap, landing gear, and slat extension configurations. The data are corrected for wind effects, atmospheric attenuation, and spherical divergence, and are normalized to a 1 meter acoustic range. The sound pressure levels are found to vary approximately as the fifth power of flight velocity. Both lift and drag dipoles exist as a significant part of the airframe noise. The sideline data imply that a significant side-force dipole exists only for the flap- and gear-down configurations; for others, the data imply the existence of only the lift and drag dipoles. The data are compared with airframe noise predictions using the drag element and the data analysis methods. Although some of the predictions are good, further work is needed to refine the methods, particularly for the flap- and gear-down configurations

The effect of configuration on strength, durability, and handle of Kevlar fabric-based materials

Five Kevlar based laminates and three Kevlar based coated materials were designed, hand made, and tested against comparative conventional Dacron based materials for strength, peel, tear, puncture, creases, and handle. Emphasis was placed on evaluating geometric orientation of constituents, use of elastomeric film in place of high modulus films, and the use of flying thread loom bias reinforcement of Kevlar yarns. Whereas, the performance of the Kevlar laminates was severely degraded by crease effects, significant gains in overall performance factors were shown for the coated Kevlar materials

Investigation of Kevlar fabric based materials for use with inflatable structures

Design, manufacture and testing of laminated and coated composite materials incorporating a structural matrix of Kevlar are reported in detail. The practicality of using Kevlar in aerostat materials is demonstrated and data are provided on practical weaves, lamination and coating particulars, rigidity, strength, weight, elastic coefficients, abrasion resistance, crease effects, peel strength, blocking tendencies, helium permeability, and fabrication techniques. Properties of the Kevlar based materials are compared with conventional, Dacron reinforced counterparts. A comprehensive test and qualification program is discussed and quantitative biaxial tensile and shear test data are provided. The investigation shows that single ply laminates of Kevlar and plastic films offer significant strength to weight improvements, are less permeable than two ply coated materials, but have a lower flex life

An atlas of 1975 GEOS-3 radar altimeter data for hurricane/tropical disturbance studies, volume 1

Geographic locations of 1975 hurricanes and other tropical disturbances were correlated with the closest approaching orbits of the GEOS-3 satellite and its radar altimeter. The disturbance locations and altimeter data were gathered for a seven-month period beginning with GEOS-3 launch in mid-April 1975. Areas of coverage were the Atlantic Ocean, the Carribean, the Gulf of Mexico, the west coast of the continental United States, and the central and western Pacific Ocean. Volume 1 contains disturbance coverage data for the Atlantic Ocean, Gulf of Mexico, and Eastern Pacific Ocean. Central and Western Pacific coverage is documented in Volume II

Investigation of Kevlar fabric-based materials for use with inflatable structures

Design, manufacture and testing of laminated and coated composite materials incorporating a structural matrix of Kevlar are reported. The practicality of using Kevlar in aerostat materials is demonstrated, and data are provided on practical weaves, lamination and coating particulars, rigidity, strength, weight, elastic coefficients, abrasion resistance, crease effects, peel strength, blocking tendencies, helium permeability, and fabrication techniques. Properties of the Kevlar-based materials are compared with conventional Dacron-reinforced counterparts. A comprehensive test and qualification program is discussed, and considerable quantitative biaxial tensile and shear test data are provided

A New Low Reynolds Number Facility for Active Flow Control Applications

Recent interest in gaining understanding of the dynamics and behavior of the leading-edge vortex structure observed in biological flight systems has prompted the construction of a new low Reynolds number facility. This facility, a recirculating oil tunnel, gives several distinct advantages over similar facilities, utilizing water or air as the working fluid, for this kind of study. Additionally, as understanding is gained, active flow control strategies leading to the stabilization of the leading-edge vortex structure will be investigated, and this facility is specially equipped to enable this study. The tunnel has been designed and installed at the California Institute of Technology Graduate Aeronautical Laboratories. Design features of the facility will be discussed, along with some preliminary measurements conducted on a NACA 0012 wing

Powder metallurgy bearings for advanced rocket engines

Traditional ingot metallurgy was pushed to the limit for many demanding applications including antifriction bearings. New systems require corrosion resistance, better fatigue resistance, and higher toughness. With conventional processing, increasing the alloying level to achieve corrosion resistance results in a decrease in other properties such as toughness. Advanced powder metallurgy affords a viable solution to this problem. During powder manufacture, the individual particle solidifies very rapidly; as a consequence, the primary carbides are very small and uniformly distributed. When properly consolidated, this uniform structure is preserved while generating a fully dense product. Element tests including rolling contact fatigue, hot hardness, wear, fracture toughness, and corrosion resistance are underway on eleven candidate P/M bearing alloys and results are compared with those for wrought 440C steel, the current SSME bearing material. Several materials which offer the promise of a significant improvement in performance were identified

Port security in the Persian Gulf

The United States and the international community have implemented numerous measures since 2001 designed to improve the security of maritime commerce. Special attention has been paid to the vulnerability of port facilities to exploitation by terrorists or other illicit actors. While the implementation of enhanced port security measures in Saudi Arabia, UAE, and Iraq may have improved some aspects of maritime security, significant vulnerabilities remain. While strong physical security at ports and stringent inspection regimes for container cargo are important elements in protecting maritime infrastructure worldwide, port security measures may yet be undermined by a failure to provide mechanisms which verify the identities and credentials of all individuals with access to ports, secure non-container cargo, and prevent illicit actors from accessing and exploiting port facilities.http://archive.org/details/portsecurityinpe109454054US Navy (USN) author.Approved for public release; distribution is unlimited

Preliminary Solar Sail Design and Fabrication Assessment: Spinning Sail Blade, Square Sail Sheet

Blade design aspects most affecting producibility and means of measurement and control of length, scallop, fullness and straightness requirements and tolerances were extensively considered. Alternate designs of the panel seams and edge reinforcing members are believed to offer advantages of seam integrity, producibility, reliability, cost and weight. Approaches to and requirements for highly specialized metalizing methods, processes and equipment were studied and identified. Alternate methods of sail blade fabrication and related special machinery, tooling, fixtures and trade offs were examined. A preferred and recommended approach is also described. Quality control plans, inspection procedures, flow charts and special test equipment associated with the preferred manufacturing method were analyzed and are discussed