Utilization of DES-Lignin as a Bio-Based Hydrophilicity Promoter in the Fabrication of Antioxidant Polyethersulfone Membranes

Enhancement of membrane permeability at no detriment of its other performances, e.g., selectivity, is a goal-directed objective in membrane fabrication. A novel antioxidant DES-lignin (lignin extracted from birch wood by using a deep eutectic solvent) polyethersulfone (PES) membrane, containing 0–1 wt % DES-lignin, was fabricated with the phase inversion technique. The performance and morphology of the fabricated membranes were characterized by a pure water flux, polyethylene glycol (PEG) retention, Fourier transform infrared spectroscopy, scanning electron microscopy, and contact angle measurements. Membranes with less negative charge and better hydrophilicity were obtained when the DES-lignin content in the polymer solution was increased. With the highest dosage, the incorporation of DES-lignin in the membrane matrix improved the membrane permeability by 29.4% compared to a pure PES membrane. Moreover, no leakage of DES-lignin from the membrane structure was observed, indicating good compatibility of DES-lignin with the PES structure. It was also found that the improvement of both rejection and pure water flux could be achieved by using a small dosage of DES-lignin (0.25 wt %) in membrane fabrication. The membranes incorporated with DES-lignin showed higher DPPH (2,2-diphenyl-1-picrylhydrazyl) and ABTS (2,2-Azino-bis (3-ethylbenzothiazoline-6-sulfonic acid)) scavenging activity compared to the pure membrane, where 2.6 and 1.1 times higher DPPH and ABTS scavenging activity was observed with the highest DES-lignin content (1 wt %). Thus, the results of this study demonstrate well the feasibility of utilizing DES-lignin as an antioxidant bio-based hydrophilicity promoter in the fabrication of ultrafiltration membranes

Vanillin as an Antifouling and Hydrophilicity Promoter Agent in Surface Modification of Polyethersulfone Membrane

Fouling as an intricate process is considered as the main obstacle in membrane technologies, and its control is one of the main areas of attention in membrane processes. In this study, a commercial polyethersulfone ultrafiltration membrane (MWCO: 4000 g/mol) was surface modified with different concentrations of vanillin as an antifouling and hydrophilicity promoter to improve its performance. The presence of vanillin and its increasing adsorption potential trends in higher vanillin concentrations were clearly confirmed by observable changes in FTIR (Fourier transform infrared) spectra after modification. Membranes with better hydrophilicity (almost 30% lower contact angle in the best case) and higher polyethylene glycol solution (PEG) permeability were achieved after modification, where a 35–38% increase in permeability of aqueous solution of PEG was perceived when the membrane was modified at the highest exposure concentration of vanillin (2.8 g/L). After filtration of wood extract, surface modified membrane (2.8 g/L vanillin) showed better antifouling characteristics compared to unmodified membrane, as indicated by approximately 22% lower pure water flux reduction, which in turn improved the separation of lignin from the other organic compounds present in wood extract

Effect of Low Concentrations of Lithium Chloride Additive on Cellulose-Rich Ultrafiltration Membrane Performance

Various water treatment processes make extensive use of porous polymeric membranes. A key objective in membrane fabrication is to improve membrane selectivity without sacrificing other properties such as permeability. Herein, LiCl (0–2 wt.%) was utilised as a preforming agent in fabricating biomass-derived cellulosic membranes. The fabricated membranes were characterised by dope solution viscosity, surface and cross-sectional morphology, pure water flux, relative molecular mass cut-off (MWCO, 35 kDa), membrane chemistry, and hydrophilicity. The results demonstrated that at the optimum LiCl concentration (0.4 wt.%), there is an interplay of thermodynamic instability and kinetic effects during membrane formation, wherein the membrane morphology and hydrophilicity can be preferably altered and thus lead to the formation of the membrane with better rejection at no detriment to its permeability

Severe Rotational Drift of an Impacted Mandibular Third Molar: A Case Report

hird molar eruption is an unpredictable event. Occasionally, mandibular third molars undergo angular changes in young adults. This rotational drift is of unknown etiology, is not predictable and may facilitate the eruption or may make the impaction worse. A rare case is presented with severe rotational drift of a mesioangularly impacted mandibular third molar

Influence of CeO2 and TiO2 Particles on Physicochemical Properties of Composite Nickel Coatings Electrodeposited at Ambient Temperature

The Ni-TiO2 and Ni-CeO2 composite coatings with varying hydrophilic/hydrophobic characteristics were fabricated by the electrodeposition method from a tartrate electrolyte at ambient temperature. To meet the requirements of tight regulation by the European Chemicals Agency classifying H3BO3 as a substance of very high concern, Rochelle salt was utilized as a buffer solution instead. The novelty of this study was to implement a simple one-step galvanostatic electrodeposition from the low-temperature electrolyte based on a greener buffer compared to traditionally used, aiming to obtain new types of soft-matrix Ni, Ni-CeO2, and Ni-TiO2 coatings onto steel or copper substrates. The surface characteristics of electrodeposited nickel composites were evaluated by SEM, EDS, surface contact angle measurements, and XPS. Physiochemical properties of pure Ni, Ni-CeO2, and Ni-TiO2 composites, namely, wear resistance, microhardness, microroughness, and photocatalytic activity, were studied. Potentiodynamic polarization, EIS, and ICP-MS analyses were employed to study the long-term corrosion behavior of coatings in a 0.5 M NaCl solution. Superior photocatalytic degradation of methylene blue, 96.2% after 6 h of illumination, was achieved in the case of Ni-TiO2 composite, while no substantial change in the photocatalytic behavior of the Ni-CeO2 compared to pure Ni was observed. Both composites demonstrated higher hardness and wear resistance than pure Ni. This study investigates the feasibility of utilizing TiO2 as a photocatalytic hydrophilicity promoter in the fabrication of composite coatings for various applications.Validerad;2022;Nivå 2;2022-08-17 (sofila)</p

Mineralogical and microstructural characterization of ceramics from the fifth and fourth millennium BC in the central plateau of Iran

This research presents the effects of sintering process and clay composition on the physico-mechanical properties of ceramics from the fifth and fourth millennium BC (6950 ± 280 to 5040 ± 220 TL dating). The combined multiscale mercury intrusion porosimetry (MIP) revealed the increase of round cryptopores and ultramicropores in a range of 0.01–0.1 μm and 0.1–5 μm respectively, closely linked to vitrified glassy connections and bonding between particles and the partial melting of phyllosilicates with different sizes of bubbles at 950 °C. Cold crushing strength (CCS) of the ceramics, containing high calcite and phyllosilicate mineral exhibited a lower strength value from 6.24 to 6.31 MPa at ∼750–800 °C due to the increase in crack porosity area with high interconnectivity and internal stresses. However, the ceramics with a well glassy network show a higher strength value of 16.5Mpa, contributing to sustainable ceramic materials with a uniform cross-section >900 °C and minimal shrinkage for conservation treatment