222 research outputs found
Gas gain and signal length measurements with a triple-GEM at different pressures of Ar-, Kr- and Xe-based gas mixtures
We investigate the gas gain behaviour of a triple-GEM configuration in gas
mixtures of argon, krypton and xenon with ten and thirty percent of carbon
dioxide at pressures between 1 and 3 bar. Since the signal widths affect the
dead time behaviour of the detector we present signal length measurements to
evaluate the use of the triple-GEM in time-resolved X-ray imaging.Comment: 19 pages, 21 figures, revised version, accepted for publication in
Nucl. Instr. and Meth.
Fast, multi-band photon detectors based on quantum well devices for beam-monitoring in new generation light sources
In order to monitor the photon-beam position for both diagnostics and calibration purposes, we have investigated the possibility to use InGaAs/InAlAs
Quantum Well (QW) devices as position-sensitive photon detectors for Free-Electron Laser (FEL) or Synchrotron Radiation (SR).
Owing to their direct, low-energy band gap and high electron mobility, such QW devices may be used also at Room Temperature (RT) as fast multi-band sensors for photons ranging from visible light to hard X-rays. Moreover, internal charge-amplification mechanism can be applied for very low signal levels, while the high carrier mobility allows the design of very fast photon detectors with sub-nanosecond response times. Segmented QW sensors have been preliminary tested with 100-fs-wide 400 nm laser pulses and X-ray SR. The reported results indicate that these devices respond with 100 ps rise-times to such ultra-fast laser pulses. Besides, linear scan on the back-pixelated device has shown that these detectors are sensitive to the position of each ultrashort beam bunch
A New Expression for the Gain-Noise Relation of Single-Carrier Avalanche Photodiodes With Arbitrary Staircase Multiplication Regions
We propose a simple expression to relate the total excess noise factor of a single-carrier multiplication staircase avalanche photodiode (APD) to the excess noise factor and gain given by the individual conduction band discontinuities. The formula is valid when electron impact ionization dominates hole impact ionization; hence, it is especially suited for staircase APDs with In-rich multiplication regions, as opposed, for example, to GaAs/AlGaAs systems where hole ionization plays an important role. The formula has been verified by accurate means of numerical simulations based on a newly developed nonlocal history dependent impact ionization model
Optimization of GaAs/AlGaAs staircase avalanche photodiodes accounting for both electron and hole impact ionization
A recently developed nonlocal history dependent model for electron and hole impact ionization is used to compute the gain and the excess noise factor in avalanche photodiodes featuring heterojunctions of III-V compound semiconductors while accounting for both carriers. The model has been calibrated with measurements by our group, as well as on noise versus gain data from the literature. We explore the avalanche photodiode design trade-offs related to the number of GaAs/AlGaAs conduction band steps for X-ray spectroscopy applications
Experimental and simulation analysis of carrier lifetimes in GaAs/AlGaAs Avalanche Photo-Diodes
Extensive experimental characterization and TCAD simulation analysis have been used to study the dark current in Avalanche Photo-Diodes (APDs). The comparison between the temperature dependence of measurements and simulations points out that SRH generation/recombination is responsible for the observed dark current. After the extraction of the carrier lifetimes in the GaAs layers, they have been used to predict the APD collection efficiency of the photo-generated currents under realistic operation conditions and as a function of the photogeneration position inside the absorption layer
Relationship between casting modulus and grain size in cast A356 aluminium alloys
Microstructure of Al-Si alloy castings depends most generally on melt preparation and on the cooling rate imposed by the thermal modulus of the component. In the case of Al-Si alloys, emphasis is put during melt preparation on refinement of pro-eutectic (Al) grains and on modification of the Al-Si eutectic. Thermal analysis has been used since long to check melt preparation before casting, i.e. by analysis of the cooling curve during solidification of a sample cast in an instrumented cup. The conclusions drawn from such analysis are however valid for the particular cooling conditions of the cups. It thus appeared of interest to investigate how these conclusions could extrapolate to predict microstructure in complicated cast parts showing local changes in the solidification conditions. For that purpose, thermal analysis cups and instrumented sand and die castings with different thermal moduli and thus cooling rates have been made, and the whole set of cooling curves thus recorded has been analysed. A statistical analysis of the characteristic features of the cooling curves related to grain refinement in sand and die castings allowed determining the most significant parameters and expressing the cube of grain size as a polynomial of these parameters. After introduction of a further parameter quantifying melt refining an excellent correlation, with a R2 factor of 0.99 was obtained
Tomographic phase and attenuation extraction for a sample composed of unknown materials using x-ray propagation-based phase-contrast imaging
Propagation-based phase-contrast x-ray imaging (PB-PCXI) generates image contrast by utilizing sample-imposed phase-shifts. This has proven useful when imaging weakly attenuating samples, as conventional attenuation-based imaging does not always provide adequate contrast. We present a PB-PCXI algorithm capable of extracting the x-ray attenuation beta and refraction delta, components of the complex refractive index of distinct materials within an unknown sample. The method involves curve fitting an error-function-based model to a phase-retrieved interface in a PB-PCXI tomographic reconstruction, which is obtained when Paganin-type phase retrieval is applied with incorrect values of delta and beta. The fit parameters can then be used to calculate true delta and beta values for composite materials. This approach requires no a priori sample information, making it broadly applicable. Our PB-PCXI reconstruction is single-distance, requiring only one exposure per tomographic angle, which is important for radiosensitive samples. We apply this approach to a breast-tissue sample, recovering the refraction component delta, with 0.6-2.4% accuracy compared with theoretical values. (C) 2022 Optica Publishing Grou
Modeling Approaches for Gain, Noise and Time Response of Avalanche Photodiodes for X-Rays Detection
We report on a suite of modeling approaches for the optimization of Avalanche Photodiodes for X-rays detection. Gain and excess noise are computed efficiently using a non-local/history dependent model that has been validated against full-band Monte Carlo simulations. The (stochastic) response of the detector to photon pulses is computed using an improved Random-Path-Length algorithm. As case studies, we consider diodes consisting of AlGaAs/GaAs multi-layers with separated absorption and multiplication regions. A superlattice creating a staircase conduction band structure is employed in the multiplication region to keep the multiplication noise low. Gain and excess noise have been measured in devices fabricated with such structure and successfully compared with the developed models
Development and tests of a new prototype detector for the XAFS beamline at Elettra Synchrotron in Trieste
The XAFS beamline at Elettra Synchrotron in Trieste combines X-ray absorption
spectroscopy and X-ray diffraction to provide chemically specific structural
information of materials. It operates in the energy range 2.4-27 keV by using a
silicon double reflection Bragg monochromator. The fluorescence measurement is
performed in place of the absorption spectroscopy when the sample transparency
is too low for transmission measurements or the element to study is too diluted
in the sample. We report on the development and on the preliminary tests of a
new prototype detector based on Silicon Drift Detectors technology and the
SIRIO ultra low noise front-end ASIC. The new system will be able to reduce
drastically the time needed to perform fluorescence measurements, while keeping
a short dead time and maintaining an adequate energy resolution to perform
spectroscopy. The custom-made silicon sensor and the electronics are designed
specifically for the beamline requirements.Comment: Proceeding of the 6YRM 12th-14th Oct 2015 - L'Aquila (Italy).
Accepted for publication on Journal of Physics: Conference Serie
- …