An experimental and modeling study of propene oxidation. Part 2: Ignition delay time and flame speed measurements

Journal articleExperimental data obtained in this study (Part II) complement the speciation data presented in Part I, but also offer a basis for extensive facility cross-comparisons for both experimental ignition delay time (IDT) and laminar flame speed (LFS) observables.To improve our understanding of the ignition characteristics of propene, a series of IDT experiments were performed in six different shock tubes and two rapid compression machines (RCMs) under conditions not previously studied. This work is the first of its kind to directly compare ignition in several different shock tubes over a wide range of conditions. For common nominal reaction conditions among these facilities, cross-comparison of shock tube IDTs suggests 20-30% reproducibility (2 sigma) for the IDT observable. The combination of shock tube and RCM data greatly expands the data available for validation of propene oxidation models to higher pressures (2-40 atm) and lower temperatures (750-1750 K).Propene flames were studied at pressures from 1 to 20 atm and unburned gas temperatures of 295-398 K for a range of equivalence ratios and dilutions in different facilities. The present propene-air LFS results at 1 atm were also compared to LFS measurements from the literature. With respect to initial reaction conditions, the present experimental LFS cross-comparison is not as comprehensive as the IDT comparison; however, it still suggests reproducibility limits for the LFS observable. For the LFS results, there was agreement between certain data sets and for certain equivalence ratios (mostly in the lean region), but the remaining discrepancies highlight the need to reduce uncertainties in laminar flame speed experiments amongst different groups and different methods. Moreover, this is the first study to investigate the burning rate characteristics of propene at elevated pressures (>5 atm).IDT and LFS measurements are compared to predictions of the chemical kinetic mechanism presented in Part I and good agreement is observed. (C) 2014 The Combustion Institute. Published by Elsevier Inc. All rights reserved.The Rensselaer group was supported by the U.S. Air Force Office of Scientific Research (Grant No. FA9550-11-1-0261) with Dr. Chiping Li as technical monitor. Work at the University of Connecticut and at Princeton University was supported as part of the Combustion Energy Frontier Research Center, an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Office of Basic Energy Science, under Award Number DE-SC0001198. The work at Stanford University was supported by the Air Force Office of Scientific Research through AFOSR Grant No. FA9550-11-1-0217, under the AFRL Integrated Product Team, with Dr. Chiping Li as contract monitor. The work at NUI Galway was kindly supported by Saudi Aramco. The work of KAUST authors was supported by Saudi Aramco under the FUELCOM program.peer-reviewe

An experimental and modeling study of propene oxidation. Part 2: Ignition delay time and flame speed measurements

Journal articleExperimental data obtained in this study (Part II) complement the speciation data presented in Part I, but also offer a basis for extensive facility cross-comparisons for both experimental ignition delay time (IDT) and laminar flame speed (LFS) observables.To improve our understanding of the ignition characteristics of propene, a series of IDT experiments were performed in six different shock tubes and two rapid compression machines (RCMs) under conditions not previously studied. This work is the first of its kind to directly compare ignition in several different shock tubes over a wide range of conditions. For common nominal reaction conditions among these facilities, cross-comparison of shock tube IDTs suggests 20-30% reproducibility (2 sigma) for the IDT observable. The combination of shock tube and RCM data greatly expands the data available for validation of propene oxidation models to higher pressures (2-40 atm) and lower temperatures (750-1750 K).Propene flames were studied at pressures from 1 to 20 atm and unburned gas temperatures of 295-398 K for a range of equivalence ratios and dilutions in different facilities. The present propene-air LFS results at 1 atm were also compared to LFS measurements from the literature. With respect to initial reaction conditions, the present experimental LFS cross-comparison is not as comprehensive as the IDT comparison; however, it still suggests reproducibility limits for the LFS observable. For the LFS results, there was agreement between certain data sets and for certain equivalence ratios (mostly in the lean region), but the remaining discrepancies highlight the need to reduce uncertainties in laminar flame speed experiments amongst different groups and different methods. Moreover, this is the first study to investigate the burning rate characteristics of propene at elevated pressures (>5 atm).IDT and LFS measurements are compared to predictions of the chemical kinetic mechanism presented in Part I and good agreement is observed. (C) 2014 The Combustion Institute. Published by Elsevier Inc. All rights reserved.The Rensselaer group was supported by the U.S. Air Force Office of Scientific Research (Grant No. FA9550-11-1-0261) with Dr. Chiping Li as technical monitor. Work at the University of Connecticut and at Princeton University was supported as part of the Combustion Energy Frontier Research Center, an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Office of Basic Energy Science, under Award Number DE-SC0001198. The work at Stanford University was supported by the Air Force Office of Scientific Research through AFOSR Grant No. FA9550-11-1-0217, under the AFRL Integrated Product Team, with Dr. Chiping Li as contract monitor. The work at NUI Galway was kindly supported by Saudi Aramco. The work of KAUST authors was supported by Saudi Aramco under the FUELCOM program