Morphological evolution of curaua fibers under acid hydrolysis

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Cellulose whiskers were obtained by means of sulfuric acid hydrolysis of curaua fibers. Before hydrolysis, the natural fibers were treated with an alkaline solution to remove the non-cellulosic content. Fiber degradation evolution and cellulose whisker formation were analyzed by structural and morphological analysis. The original fiber structure underwent a fragmentation mechanism after being exposed for 3 min to sulfuric acid. Cellulose whiskers were lixiviated from the fiber surface after 10 min of hydrolysis, developing two scenarios: one where the whiskers became unattached from the original fiber, and the other which remained attached. The cellulose whiskers presented a needle-like geometry with an approximate diameter of 11 nm and average length of 185 nm, after 30 min of acid hydrolysis. Based on microscopic characterization, a schematic representation of the morphological evolution of the cellulose fibers submitted to acid hydrolysis is proposed.19411991207Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP

Surface modification of cotton nanocrystals with a silane agent

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)The research herewith aims at obtaining cellulose nanocrystals with a reduced hydrophilic surface character using a silane with isocyanate groups (isocyanatepropyltriethoxysilane), which are very reactive to hydroxyl groups and thus, are readily able to react with the low quantity of free hydroxyl groups present in the cellulose nanocrystal surfaces, therefore, promoting surface modification. Cellulose nanocrystals were obtained by hydrochloric acid hydrolysis of cotton fiber and were characterized by X-ray diffraction, Fourier transform infrared spectroscopy (FTIR) and solid state Si-29 nuclear magnetic resonance (NMR) and their morphologies were investigated by scanning and transmission electron microscopy techniques. The nanocrystals presented a needle-like geometry with a 10 nm approximate diameter and a 166 nm average length. FTIR, Si-29 NMR and silicon mapping images showed that nanocrystal surface chemical modification was successfully achieved. Also, the results confirm that the chemical modification occurred mainly at the nanocrystal surface, keeping the morphological integrity of the nanocrystals. The applied methodology for surface modification of the cellulose nanocrystals provided nanofillers with more appropriate surface characteristics that allow the dispersion in polymeric matrices and the adhesion at filler-matrix interface to be obtained. This may result in a better performance of these nanocrystals as reinforcing agents of hydrophobic polymer matrices.201217226Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP

Cellulose Acetate/Polysilsesquioxane Composites: Thermal Properties and Morphological Characterization by Electron Spectroscopy Imaging

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Cellulose acetate (CA) composites using two types of silane coupling agents (methyltrimethoxysilane and phenyltriethoxysilane) were prepared through two methodologies: direct reaction between CA and the specific monomer and reaction of CA with oligomers, which were produced by prehydrolysis of the same monomers. The thermal behavior and morphology of the materials were studied. The composites showed thermal stability similar to pure CA, increase of residue content at 790 degrees C and reduction in the glass transition temperature. Complementary microscopy techniques were applied to investigate the distribution of polysilsesquioxane in the CA matrix. Silicon mapping images showed the presence of domains with higher polysilsesquioxane concentration than the matrix and also the presence of silicon-rich nanodomains dispersed throughout the matrix. Based on mapping characterization, a schematic representation of the CA/polysilsesquioxane composite morphology was proposed. The organosilane type and architecture influenced the thermal behavior and the morphology of these materials. The results suggest that the silane coupling agents could be used to produce CA films with a range of properties. (C) 2011 Wiley Periodicals, Inc. J Appl Polym Sci 123: 2027-2035, 2012123420272035Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES

Poly(Ethylene Glycol) as a Compatibilizer for Poly(Lactic Acid)/Thermoplastic Starch Blends

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)A new route to prepare poly(lactic acid) (PLA)/thermoplastic starch (TPS) blends is described in this work using poly(ethylene glycol) (PEG), a non-toxic polymer, as a compatibilizer. The influence of PEG on the morphology and properties of PLA/TPS blends was studied. The blends were processed using a twin-screw micro-compounder and a micro-injector. The morphologies were analyzed by scanning and transmission electron microscopies and the material properties were evaluated by dynamic-mechanical, differential scanning calorimetry, thermogravimetric analysis and mechanical tests. PLA/TPS blends presented large TPS phase size distribution and low adhesion between phases which was responsible for the lower elastic modulus of this blend when compared to pure PLA. The addition of PEG resulted in the increase of PLA crystallization, due to its plasticizing effect, and improvement of the interfacial interaction between TPS and PLA matrix. Results show that incorporation of PEG increased the impact strength of the ternary blend and that the elastic modulus remained similar to the PLA/TPS blend.211151159Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP

Influence of the layered silicate type on the structure, morphology and properties of cellulose acetate nanocomposites

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)This paper deals with the effect of different montmorillonite source clays, including pristine and organophilic montmorillonites, on the structure, morphology and properties of cellulose acetate (CA)/clay nanocomposites. In this study, the nanocomposites were prepared by melt extrusion in the presence of the environmentally friendly triethyl citrate plasticizer. The structure and morphology of the materials were analysed by X-ray diffraction and scattering (SAXS), X-ray microtomography and energy filtered transmission electron microscopy (EFTEM). SAXS and EFTEM results indicated that the nanocomposite morphologies were made up of tactoids together with exfoliated clay platelets in different proportions depending on the clay type. It can be concluded that well distributed clay tactoids and platelets can be achieved in CA nanocomposites prepared by melt extrusion and consequently property improvements can be found by using pristine or organophilic clays. In this case, the addition of a plasticizer, able to intercalate in the clay gallery, seems to be sufficient to promote the clay delamination mechanism under shearing inside the cellulose acetate matrix.202675686Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP