La Gestione degli Accordi di Cooperazione nel progetto OpenSPCoop

Dalla analisi delle specifiche CNIPA alla realizzazione del componente Accordo di Cooperazione nel progetto OpenSPCoop con relativi casi d'uso per mostrarne le qualità e le applicazioni

Adiabatic normal zone development in MgB2 superconductors

A-priori knowledge of the normal zone development in MgB/sub 2/ conductors is essential for quench protection of applications. Therefore the normal zone propagation in a monofilament MgB/sub 2//Fe conductor under near-adiabatic conditions at 4.2 K has been measured and simulated. The results show normal zone propagation velocities up to several meters per second. In addition, by including the voltage-current relation into the computational model, the influence of the n-value on the normal zone propagation is determined. The simulations show that lower n-values suppress the normal zone propagation velocity due to lower heat generation in the MgB/sub 2/ filaments

Consequences of the peculiar intrinsic properties of MgB2 on its macroscopic current flow

The influence of two important features of magnesium diboride on the macroscopic transport properties of polycrystalline MgB2 is discussed in the framework of a percolation model. While two band superconductivity does not have significant consequences in the field and temperature range of possible power applications, the opposite is true for the anisotropy of the upper critical field. The field dependence of the critical current densities strongly increases and the macroscopic supercurrents disappear well below the apparent upper critical field. The common scaling laws for the field dependence of the volume pinning force are altered and Kramer's plot is no longer linear, although grain boundary pinning dominates in nearly all polycrystalline MgB2 conductors. In contrast to the conventional superconductors NbTi and Nb3Sn, a significant critical current anisotropy can be induced by the preparation technique of MgB2 tapes

Strong enhancement of Jc in binary and alloyed in-situ MgB2 wires by a new approach: Cold high pressure densification

Cold high pressure densification (CHPD) is presented as a new way to substantially enhance the critical current density of in situ MgB2 wires at 4.2 and 20 K at fields between 5 and 14 T. The results on two binary MgB2 wires and an alloyed wire with 10 wt.% B4C are presented The strongest enhancement was measured at 20K, where cold densification at 1.85 GPa on a binary Fe/MgB2 wire raised both Jcpara and Jcperp by more than 300% at 5T, while Birr was enhanced by 0.7 T. At 4.2K, the enhancement of Jc was smaller, but still reached 53% at 10 T. After applying pressures up to 6.5 GPa, the mass density dm of the unreacted (B+Mg) mixture inside the filaments reached 96% of the theoretical density. After reaction under atmospheric pressure, this corresponds to a highest mass density df in the MgB2 filaments of 73%. After reaction, the electrical resistance of wires submitted to cold densification was found to decrease, reflecting an improved connectivity. A quantitative correlation between filament mass density and the physical properties was established. Monofilamentary rectangular wires with aspect ratios a/b < 1.25 based on low energy ball milled powders exhibited very low anisotropy ratios, Gamma = Jcpara/Jcperp being < 1.4 at 4.2 K and 10T. The present results can be generalized to alloyed MgB2 wires, as demonstrated on a wire with B4C additives. Based on the present data, it follows that cold densification has the potential of further improving the highest Jcpara and Jcperp values reported so far for in situ MgB2 tapes and wires with SiC and C additives. Investigations are under work in our laboratory to determine whether the densification method CHPD can be applied to longer wire or tape lengths.Comment: Submitted to Superconductors Science and Technolog