Aerodynamic drag and fuel spreading measurements in a simulated scramjet combustion module

The drag of a simulated scramjet combustion module was measured at Mach 2, 2.5, and 3. The combustor was rectangular in cross section and incorporated six swept fuel injector struts. The effect of strut leading edge radius, position of maximum thickness, thickness ratio, sweep angle, and strut length on the drag was determined. Reduction in thickness ratio had the largest effect on drag reduction. Sweeping the struts upstream yielded the same drag as sweeping the struts downstream and potentially offers the advantages of increased mixing time for the fuel. Helium injection was used to simulate hydrogen fuel. The interstrut spacing required to achieve good distribution of fuel was was found to be about 10 jet diameters. The contribution of helium injection to drag reduction was small

An aerodynamic study of scramjet fuel injectors

The aerodynamic drag and fuel distribution patterns of injectors designed for a supersonic combustion ramjet were measured at Mach numbers of 2, 2.5, and 3. The most significant parameter effecting the drag was found to be the injector thickness ratio. A two-fold reduction in the thickness ratio caused a 65 percent decrease in drag. Changing the injector sweep angle a factor of 2 resulted in only a small change in drag. A reversal of injector sweep, from sweepback to sweepforward, did not change the measured drag. Helium gas was injected through the struts to simulate the penetration and spreading patterns of hydrogen. Sampling measurements were made at approximately 2 duct heights downstream of the combustor. The spacing required between fuel injectors was found to be about 10 jet diameters. The effect of gas injection on the measured drag was found to be minor

Optical study of sonic and supersonic jet penetration from a flat plate into a Mach 2 airstream

Optical study of sonic and supersonic jet penetration from flat plate into Mach 2 airstrea

Validation of viscous and inviscid computational methods for turbomachinery components

An assessment of several three-dimensional computer codes used at the NASA Lewis Research Center is presented. Four flow situations are examined, for which both experimental data and computational results are available. The four flows form a basis for the evaluation of the computational procedures. It is concluded that transonic rotor flow at peak efficiency conditions may be calculated with a reasonable degree of accuracy, whereas, off-design conditions are not accurately determined. Duct flows and turbine cascade flows may also be computed with reasonable accuracy whereas radial inflow turbine flow remains a challenging problem

An experimental and analytical investigation of axisymmetric diffusers

A finite difference computer program for turbulent compressible flow was used to establish the performance of several diffuser shapes for experimental testing. The diffusers were designed to have a linear change in Mach number, a linear change in pressure, or a curvature fitted by a quadratic equation. Testing was performed with M = 0.1 to 0.9 with and without boundary layer bleed. Above M = 0.6, data were obtained with a normal shock upstream of the diffuser entrance. Peak static pressure recovery occurred with a diffuser inlet M0.75. The quadratic diffuser yielded the highest total pressure recovery

Some aspects of steady-state propellant combustion as related to dynamic coupling mechanisms

Dynamic pressure and velocity coupling mechanisms in steady-state solid propellant combustio

Fluid and gas dynamics

A clearer understanding of the interactions of the hot gas flow with the structure in the duct system, the flow passages of the rotating machinery, and the thrust chamber nozzle is sought for the purpose of finding ways and means to increase the life and performance of the systems. The objective of the transient nozzle test is to understand the shock-boundary layer interactions during transient flow and the resulting large side forces acting on the nozzle skirt. The Fluctuating Pressures in Ducts study deals mainly with the fluid-structural interactions of the lox post tube banks in the injector. The Ablative Nozzle Insert Study (H4) has as its goal the performance improvement of the space shuttle main engine

Burning rate control of solid propellants Patent

Pressurized gas injection for burning rate control of solid propellant

Influence of pressure driven secondary flows on the behavior of turbofan forced mixers

A finite difference procedure was developed to analyze the three dimensional subsonic turbulent flows in turbofan forced mixer nozzles. The method is based on a decomposition of the velocity field into primary and secondary flow components which are determined by solution of the equations governing primary momentum, secondary vorticity, thermal energy, and continuity. Experimentally, a strong secondary flow pattern was identified which is associated with the radial inflow and outflow characteristics of the core and fan streams and forms a very strong vortex system aligned with the radial interface between the core and fan regions. A procedure was developed to generate a similar generic secondary flow pattern in terms of two constants representing the average radial outflow or inflow in the core and fan streams as a percentage of the local streamwise velocity. This description of the initial secondary flow gave excellent agreement with experimental data. By identifying the nature of large scale secondary flow structure and associating it with characteristic mixer nozzle behavior, it is felt that the cause and effect relationship between lobe design and nozzle performance can be understood

Comparison of secondary flows predicted by a viscous code and an inviscid code with experimental data for a turning duct

A comparison of the secondary flows computed by the viscous Kreskovsky-Briley-McDonald code and the inviscid Denton code with benchmark experimental data for turning duct is presented. The viscous code is a fully parabolized space-marching Navier-Stokes solver while the inviscid code is a time-marching Euler solver. The experimental data were collected by Taylor, Whitelaw, and Yianneskis with a laser Doppler velocimeter system in a 90 deg turning duct of square cross-section. The agreement between the viscous and inviscid computations was generally very good for the streamwise primary velocity and the radial secondary velocity, except at the walls, where slip conditions were specified for the inviscid code. The agreement between both the computations and the experimental data was not as close, especially at the 60.0 deg and 77.5 deg angular positions within the duct. This disagreement was attributed to incomplete modelling of the vortex development near the suction surface