Rail accelerator technology and applications

Rail accelerators offer a viable means of launching ton-size payloads from the Earth's surface to space. The results of two mission studies which indicate that an Earth-to-Space Rail Launcher (ESRL) system is not only technically feasible but also economically beneficial, particularly when large amounts of bulk cago are to be delivered to space are given. An in-house experimental program at the Lewis Research Center (LeRC) was conducted in parallel with the mission studies with the objective of examining technical feasibility issues. A 1 m long - 12.5 by 12.5 mm bore rail accelerator as designed with clear polycarbonate sidewalls to visually observe the plasma armature acceleration. The general character of plasma/projectile dynamics is described for a typical test firing

SERT II 1980 extended flight thruster experiments

The flight results obtained from mid 1979 through December 1980 are presented. Near continuous solar power in 1979 and 1980 has enabled long periods of thruster endurance testing. Three of four propellant tanks were exhausted with no significant change in thruster system operation before being empty. A new plasma mode thrust was characterized and direct thrust measurements obtained. Other tests, including beam neutralization by various neutralizer sources, give insight to electron conduction across plasmas in space and provide a basis to model neutralization of thruster arrays

Rail accelerators for space transportation: An experimental investigation

An experimental program was conducted at the Lewis Research Center with the objective of investigating the technical feasibility of rail accelerators for propulsion applications. Single-stage, plasma driven rail accelerators of small (4 by 6 mm) and medium (12.5 by 12.5 mm) bores were tested at peak accelerating currents of 50 to 450 kA. Streak-camera photography was used to provide a qualitative description of plasma armature acceleration. The effects of plasma blowby and varying bore pressure on the behavior of plasma armatures were studied

Structural assessment of a space station solar dynamic heat receiver thermal energy storage canister

The structural performance of a space station thermal energy storage (TES) canister subject to orbital solar flux variation and engine cold start up operating conditions was assessed. The impact of working fluid temperature and salt-void distribution on the canister structure are assessed. Both analytical and experimental studies were conducted to determine the temperature distribution of the canister. Subsequent finite element structural analyses of the canister were performed using both analytically and experimentally obtained temperatures. The Arrhenius creep law was incorporated into the procedure, using secondary creep data for the canister material, Haynes 188 alloy. The predicted cyclic creep strain accumulations at the hot spot were used to assess the structural performance of the canister. In addition, the structural performance of the canister based on the analytically determined temperature was compared with that based on the experimentally measured temperature data

Full-size solar dynamic heat receiver thermal-vacuum tests

The testing of a full-size, 120 kW, solar dynamic heat receiver utilizing high-temperature thermal energy storage is described. The purpose of the test program was to quantify receiver thermodynamic performance, operating temperatures, and thermal response to changes in environmental and power module interface boundary conditions. The heat receiver was tested in a vacuum chamber with liquid nitrogen cold shrouds and an aperture cold plate to partly simulate a low-Earth-orbit environment. The cavity of the receiver was heated by an infrared quartz lamp heater with 30 independently controllable zones to allow axially and circumferentially varied flux distributions. A closed-Brayton cycle engine simulator conditioned a helium-xenon gas mixture to specific interface conditions to simulate the various operational modes of the solar dynamic power module on the Space Station Freedom. Inlet gas temperature, pressure, and flow rate were independently varied. A total of 58 simulated orbital cycles, each 94 minutes in duration, was completed during the test conduct period

Ground test program for a full-size solar dynamic heat receiver

Test hardware, facilities, and procedures were developed to conduct ground testing of a full size, solar dynamic heat receiver in a partially simulated, low Earth orbit environment. The heat receiver was designed to supply 102 kW of thermal energy to a helium and xenon gas mixture continuously over a 94 minute orbit, including up to 36 minutes of eclipse. The purpose of the test program was to quantify the receiver thermodynamic performance, its operating temperatures, and thermal response to changes in environmental and power module interface boundary conditions. The heat receiver was tested in a vacuum chamber using liquid nitrogen cold shrouds and an aperture cold plate. Special test equipment were designed to provide the required ranges in interface boundary conditions that typify those expected or required for operation as part of the solar dynamic power module on the Space Station Freedom. The support hardware includes an infrared quartz lamp heater with 30 independently controllable zones and a closed Brayton cycle engine simulator to circulate and condition the helium xenon gas mixture. The test article, test support hardware, facilities, and instrumentation developed to conduct the ground test program are all described

Two-dimensional magnetism in the pnictide superconductor parent material SrFeAsF probed by muon-spin relaxation

We report muon-spin relaxation measurements on SrFeAsF, which is the parent compound of a newly discovered iron-arsenic-fluoride based series of superconducting materials. We find that this material has very similar magnetic properties to LaFeAsO, such as separated magnetic and structural transitions (TN = 120 K, Ts = 175 K), contrasting with SrFe2As2 where they are coincident. The muon oscillation frequencies fall away very sharply at TN, which suggests that the magnetic exchange between the layers is weaker than in comparable oxypnictide compounds. This is consistent with our specific heat measurements, which find that the entropy change S = 0.05 J/mol/K largely occurs at the structural transition and there is no anomaly at TN.Comment: 4 pages, 3 figure

Solar Electric Power System Analyses for Mars Surface Missions

The electric power system is a crucial element of any architecture supporting human surface exploration of Mars. In this paper, we describe the conceptual design and detailed analysis of solar electric power system using photovoltaics and regenerative fuel cells to provide surface power on Mars. System performance, mass and deployed area predictions are discussed along with the myriad environmental factors and trade study results that helped to guide system design choices. Based on this work, we have developed a credible solar electric power option that satisfies the surface power requirements of a human Mars mission. The power system option described in this paper has a mass of approximately 10 metric tons, a approximately 5000-sq m deployable photovoltaic array using thin film solar cell technology

The LeRC rail accelerators: Test designs and diagnostic techniques

The feasibility of using rail accelerators for various in-space and to-space propulsion applications was investigated. A 1 meter, 24 sq mm bore accelerator was designed with the goal of demonstrating projectile velocities of 15 km/sec using a peak current of 200 kA. A second rail accelerator, 1 meter long with a 156.25 sq mm bore, was designed with clear polycarbonate sidewalls to permit visual observation of the plasma arc. A study of available diagnostic techniques and their application to the rail accelerator is presented. Specific topics of discussion include the use of interferometry and spectroscopy to examine the plasma armature as well as the use of optical sensors to measure rail displacement during acceleration. Standard diagnostics such as current and voltage measurements are also discussed

Preliminary study of Australian Pinot noir wines by colour and volatile analyses, and the Pivot© Profile method using wine professionals

The aim of this preliminary study was to identify potential colour components, volatile and sensory attributes that could discriminate Pinot noir wines from five Australian winegrowing regions (Adelaide Hills, Yarra Valley, Mornington Peninsula, Northern and Southern Tasmania). The sensory analysis consisted of the Pivot© Profile method that was performed by wine professionals. A headspace solid-phase microextraction-gas chromatography-mass spectrometry method was used to quantify multiple volatile compounds, while the Modified Somers method was used for colour characterisation. Analysis of data suggested ethyl decanoate, ethyl 2-methylpropanoate, ethyl 2-methylbutanoate, in addition to decanoic acid as important contributors to the discrimination between regions. Similarly, wine hue, chemical age indices, total anthocyanin, and (%) non-bleachable pigment also discriminated wines between regions. The sensory analysis showed that wines from Mornington Peninsula were associated with the ‘red fruits’ aroma, ‘acidic’, and ‘astringency’ palate descriptors, while those from Adelaide Hills were associated with the ‘brown’ colour attribute. This study indicates regionality is a strong driver of aroma typicity of wine