Transonic wind tunnel test of a 14 percent thick oblique wing

An experimental investigation was conducted at the ARC 11- by 11-Foot Transonic Wind Tunnel as part of the Oblique Wing Research Aircraft Program to study the aerodynamic performance and stability characteristics of a 0.087-scale model of an F-8 airplane fitted with an oblique wing designed by Rockwell International. The 10.3 aspect ratio, straight-tapered wing of 0.14 thickness/chord ratio was tested at two different mounting heights above the fuselage. Additional tests were conducted to assess low-speed behavior with and without flaps, aileron effectiveness at representative flight conditions, and transonic drag divergence with 0 degree wing sweep. Longitudinal stability data were obtained at sweep angles of 0, 30, 45, 60, and 65 degrees, at Mach numbers ranging from 0.25 to 1.40. Test Reynolds numbers varied from 3.2 to 6.6 x 10 exp 6/ft. and angle of attack ranged from -5 to +18 degrees. Most data were taken at zero sideslip, but a few runs were at sideslip angles of +/- 5 degrees. The raised wing position proved detrimental overall, although side force and yawing moment were reduced at some conditions. Maximum lift coefficient with the flaps deflected was found to fall short of the value predicted in the preliminary design document. The performance and trim characteristics of the present wing are generally inferior to those obtained for a previously tested wing designed at ARC

Miniature Trailing Edge Effector for Aerodynamic Control

Improved miniature trailing edge effectors for aerodynamic control are provided. Three types of devices having aerodynamic housings integrated to the trailing edge of an aerodynamic shape are presented, which vary in details of how the control surface can move. A bucket type device has a control surface which is the back part of a C-shaped member having two arms connected by the back section. The C-shaped section is attached to a housing at the ends of the arms, and is rotatable about an axis parallel to the wing trailing edge to provide up, down and neutral states. A flip-up type device has a control surface which rotates about an axis parallel to the wing trailing edge to provide up, down, neutral and brake states. A rotating type device has a control surface which rotates about an axis parallel to the chord line to provide up, down and neutral states

Experimental Aerodynamic Characteristics of an Oblique Wing for the F-8 OWRA

An experimental investigation was conducted during June-July 1987 in the NASA Ames 11-Foot Transonic Wind Tunnel to study the aerodynamic performance and stability and control characteristics of a 0.087-scale model of an F-8 airplane fitted with an oblique wing. This effort was part of the Oblique Wing Research Aircraft (OWRA) program performed in conjunction with Rockwell International. The Ames-designed, aspect ratio 10.47, tapered wing used specially designed supercritical airfoils with 0.14 thickness/chord ratio at the root and 0.12 at the 85% span location. The wing was tested at two different mounting heights above the fuselage. Performance and longitudinal stability data were obtained at sweep angles of 0deg, 30deg, 45deg, 60deg, and 65deg at Mach numbers ranging from 0.30 to 1.40. Reynolds number varied from 3.1 x 10(exp 6)to 5.2 x 10(exp 6), based on the reference chord length. Angle of attack was varied from -5deg to 18deg. The performance of this wing is compared with that of another oblique wing, designed by Rockwell International, which was tested as part of the same development program. Lateral-directional stability data were obtained for a limited combination of sweep angles and Mach numbers. Sideslip angle was varied from -5deg to +5deg. Landing flap performance was studied, as were the effects of cruise flap deflections to achieve roll trim and tailor wing camber for various flight conditions. Roll-control authority of the flaps and ailerons was measured. A novel, deflected wing tip was evaluated for roll-control authority at high sweep angles

ENHANCED COLLABORATIVE OPTIMIZATION: A DECOMPOSITION-BASED METHOD FOR MULTIDISCIPLINARY DESIGN

Astute choices made early in the design process provide the best opportunity for reducing the life cycle cost of a new product. Optimal decisions require reasonably detailed disciplinary analyses, which pose coordination challenges. These types of complex multidisciplinary problems are best addressed through the use of decomposition-based methods, several of which have recently been developed. Two of these methods are collaborative optimization (CO) and analytical target cascading (ATC). CO was conceived in 1994 in response to multidisciplinary design needs in the aerospace industry. Recent progress has led to an updated version, enhanced collaborative optimization (ECO), that is introduced in this paper. ECO addresses many of the computational challenges inherent in CO, yielding significant computational savings and more robust solutions. ATC was formalized in 2000 to address needs in the automotive industry. While ATC was originally developed for object-based decomposition, it is also applicable to multidisciplinary design problems. In this paper, both methods are applied to a set of test cases. The goal is to introduce the ECO methodology by comparing and contrasting it with ATC, a method familiar within the mechanical engineering design community. Comparison of ECO and ATC is not intended to establish the computational superiority of either method. Rather, these two methods are compared as a means of highlighting several promising approaches to the coordination of distributed design problems