Annual Thermodynamic Analysis of Solar Power with Steam Injection Gas Turbine (STIG) Cycle for Indian Conditions

AbstractSolar thermal energy is now being widely utilized to meet the world's energy demand due to its huge potential. Power generation from solar is varying and high cost of solar thermal energy systems that makes sense only in regions with high solar insolation. In order to overcome these practical issues, low cost solar hybrid steam injection gas turbine (STIG) cycle is adapted. Both gas turbine exhaust stream and solar heat are used for steam generation, and then it is injected into the combustor. The steam injection reduces NOX and CO2 emission in addition to increased power output and plant efficiency compared to the simple cycle. It offers a path for high conversion efficiency without the requirement of operating at high temperature and high pressure in the solar components. The objective of the proposed work is to investigate a conversion method for solar radiation that offers potentially high conversion efficiency and for increased competitiveness against fossil fuels. The annual performance of the cycle for sites in India with local climatic conditions such as ambient temperature, relative humidity and availability of direct normal irradiance to the solar concentrators under two modes of constant and variable power is presented in this paper. The results reveal that the solar to electricity efficiency of solar hybrid STIG plant with a simple Parabolic Trough Collector (PTC) is similar to existing solar thermal technologies and higher solar share is obtained. The study also reveals that the annual CO2 emission is similar to combined cycle plants and lower than gas turbine technologies

Concentrated Solar Power: Components and materials

CSP technologies are well developed and offer many advantages compared to other renewable energy options. They can also be very effective in many locations with high solar radiation around the world. However today they are less competitive than other technologies. Understanding the limitations, and identifying opportunities for improvements, requires a detailed analysis of the energy conversion processes, the needed components, and the required technologies for these plant components. Here we present the three main energy conversion steps in a CSP plant, the behavior and limitations of the technologies that are currently used in commercial CSP plants, and some directions for development of plant components that will offer better performance

Solar energy conversion with photon-enhanced thermionic emission

Photon-enhanced thermionic emission (PETE) converts sunlight to electricity with the combined photonic and thermal excitation of charge carriers in a semiconductor, leading to electron emission over a vacuum gap. Theoretical analyses predict conversion efficiency that can match, or even exceed, the efficiency of traditional solar thermal and photovoltaic converters. Several materials have been examined as candidates for radiation absorbers and electron emitters, with no conclusion yet on the best set of materials to achieve high efficiency. Analyses have shown the complexity of the energy conversion and transport processes, and the significance of several loss mechanisms, requiring careful control of material properties and optimization of the device structure. Here we survey current research on PETE modeling, materials, and device configurations, outline the advances made, and stress the open issues and future research needed. Based on the substantial progress already made in this young topic, and the potential of high conversion efficiency based on theoretical performance limits, continued research in this direction is very promising and may yield a competitive technology for solar electricity generation

PCM Storage System with Integrated Active Heat Pipe

AbstractThe use of the latent heat of phase change materials (PCM) is considered a promising approach to store heat at a nearly constant temperature for direct steam generation (DSG), but the poor thermal conductivity of commonly available storage materials imposes severe limitations on storage performance. A new method is proposed to overcome the limitations of the low thermal conductivity. The approach is to physically decouple the evaporator pipes from the PCM, thus allowing independent sizing of each component. The thermal link between the two components is done via evaporation and condensation of a heat transfer fluid (HTF), according to the principle of a heat pipe. Pumping the liquid HTF provides active control of the heat pipe operation. The new concept is modeled and compared to the conventional design of conduction based PCM annulus around the steam pipe. An example case shows a significant advantage in performance of the active heat pipe configuration due to its reduced thermal resistance

Solar energy conversion with photon-enhanced thermionic emission

Photon-enhanced thermionic emission (PETE) converts sunlight to electricity with the combined photonic and thermal excitation of charge carriers in a semiconductor, leading to electron emission over a vacuum gap. Theoretical analyses predict conversion efficiency that can match, or even exceed, the efficiency of traditional solar thermal and photovoltaic converters. Several materials have been examined as candidates for radiation absorbers and electron emitters, with no conclusion yet on the best set of materials to achieve high efficiency. Analyses have shown the complexity of the energy conversion and transport processes, and the significance of several loss mechanisms, requiring careful control of material properties and optimization of the device structure. Here we survey current research on PETE modeling, materials, and device configurations, outline the advances made, and stress the open issues and future research needed. Based on the substantial progress already made in this young topic, and the potential of high conversion efficiency based on theoretical performance limits, continued research in this direction is very promising and may yield a competitive technology for solar electricity generation