MODELING AND SIMULATION OF IN SITU BIOREMEDIATION FOR TCE-CONTAMINATED GROUNDWATER THROUGH METHANE INJECTION IN KIMITSU CITY JAPAN

Joint Research on Environmental Science and Technology for the Eart

Physical properties and wear behavior of CAD/CAM resin composite blocks containing S-PRG filler for restoring primary molar teeth

Objectives: This study aimed to develop computer-aided design/computer-aided manufacturing (CAD/CAM) resin composite blocks (RCBs) containing surface pre-reacted glass-ionomer (S-PRG) filler for primary molar teeth and evaluate their physical properties and wear resistance. Methods: Experimental CAD/CAM RCBs containing S-PRG filler for primary molar teeth (EB), a commercial CAD/CAM RCB (HC), two resin composites for primary teeth (BKP and BKZ) and one for permanent teeth (BⅡ) were used. Hardness tests, three-point bending tests, fracture toughness tests, and water absorption tests were conducted. Wear tests were conducted for these materials and stainless steel crowns (SSCs). Results: The Vickers hardness of EB was lower than that of HC (p 0.05). After 1 week of water immersion, EB and HC showed greater flexural strength than the other materials (p < 0.05). EB showed greater fracture toughness than the other materials (p < 0.05). The water absorption of EB was lower than that of HC, BKZ, and BKP (p < 0.05), and greater than that of BⅡ (p < 0.05). Antagonist wear was significantly smaller in EB than in HC and BⅡ (p < 0.05), and significantly greater than in BKZ (p < 0.05). Antagonist wear could not be measured in SSC because of excessive wear that was out of range of the surface roughness tester. Significance: The CAD/CAM RCBs containing S-PRG filler for primary molar teeth developed in this study demonstrated adequate physical properties and wear performance, suggesting that they are suitable for restoration of primary molar teeth and could function in place of SSCs.Nakase Y., Yamaguchi S., Okawa R., et al. Physical properties and wear behavior of CAD/CAM resin composite blocks containing S-PRG filler for restoring primary molar teeth. Dental Materials 38, 158 (2022); https://doi.org/10.1016/j.dental.2021.11.001

Multi-scale analysis of the effect of nano-filler particle diameter on the physical properties of CAD/CAM composite resin blocks

The objective of this study was to assess the effect of silica nano-filler particle diameters in a computer-aided design/manufacturing (CAD/CAM) composite resin (CR) block on physical properties at the multi-scale in silico. CAD/CAM CR blocks were modeled, consisting of silica nano-filler particles (20, 40, 60, 80, and 100 nm) and matrix (Bis-GMA/TEGDMA), with filler volume contents of 55.161%. Calculation of Young’s moduli and Poisson’s ratios for the block at macro-scale were analyzed by homogenization. Macro-scale CAD/CAM CR blocks (3 × 3 × 3 mm) were modeled and compressive strengths were defined when the fracture loads exceeded 6075 N. MPS values of the nano-scale models were compared by localization analysis. As the filler size decreased, Young’s moduli and compressive strength increased, while Poisson’s ratios and MPS decreased. All parameters were significantly correlated with the diameters of the filler particles (Pearson’s correlation test, r = −0.949, 0.943, −0.951, 0.976, p < 0.05). The in silico multi-scale model established in this study demonstrates that the Young’s moduli, Poisson’s ratios, and compressive strengths of CAD/CAM CR blocks can be enhanced by loading silica nanofiller particles of smaller diameter. CAD/CAM CR blocks by using smaller silica nano-filler particles have a potential to increase fracture resistance.This is an Accepted Manuscript of an article published by Taylor & Francis in Computer Methods in Biomechanics and Biomedical Engineering on 19 May 2017, available at https://doi.org/10.1080/10255842.2017.1293664

慢性硬化性唾液腺炎の病態形成におけるIgG4陽性形質細胞浸潤の関与について

取得学位 : 博士（医学）, 学位授与番号 : 医博甲第1760号 , 学位授与年月日 : 平成18年3月22日, 学位授与大学 : 金沢大

Glass-phase coordination polymer displaying proton conductivity and guest-accessible porosity

We describe the preparation of the crystalline and glassy state of a coordination polymer displaying proton conduction and guest-accessible porosity. EXAFS and solid-state NMR analyses indicated that pyrophosphate and phosphate ions are the main proton transporters in the glass and that homogeneously distributed 5-chloro-1H-benzimidazole in the glass provide the porosity

微小物体可視化センサLSIの設計

金沢大学大学院自然科学研究科情報システム金沢大学工学

Molecular characterization of the CRa gene conferring clubroot resistance in Brassica rapa

Clubroot disease is one of the major diseases affecting Brassicaceae crops, and a number of these crops grown commercially, such as Chinese cabbage (Brassica rapa L. ssp. pekinensis), are known to be highly susceptible to clubroot disease. To provide protection from this disease, plant breeders have introduced genes for resistance to clubroot from the European turnip into susceptible lines. The CRa gene confers specific resistance to the clubroot pathogen Plasmodiophora brassicae isolate M85. Fine mapping of the CRa locus using synteny to the Arabidopsis thaliana genome and partial genome sequences of B. rapa revealed a candidate gene encoding a TIR-NBS-LRR protein. Several structural differences in this candidate gene were found between susceptible and resistant lines, and CRa expression was observed only in the resistant line. Four mutant lines lacking clubroot resistance were obtained by the UV irradiation of pollen from a resistant line, and all of these mutant lines carried independent mutations in the candidate TIR-NBS-LRR gene. This genetic and molecular evidence strongly suggests that the identified gene is CRa. This is the first report on the molecular characterization of a clubroot Resistance gene in Brassicaceae and of the disease resistance gene in B. rapa.ArticlePLANT MOLECULAR BIOLOGY. 80(6):621-629 (2012)journal articl

Order-to-disorder structural transformation of a coordination polymer and its influence on proton conduction.

Accepted 14 Jul 2014.We observed an ordered-to-disordered structural transformation in a Cu(2+) coordination polymer and investigated its influence on the proton conductivity. The transformation generated highly mobile proton carriers in the structure. The resulting material exhibited a conductivity greater than 10(-2) S cm(-1) at 130 °C. The structural transformation and the conduction mechanism were investigated by EXAFS, TPD-MS and NMR