20,329 research outputs found
Effects of real-time thermal aging on graphite/polyimide composites
As part of a program to evaluate high-temperature advanced composites for use on supersonic cruise transport aircraft, two graphite/polyimide composites have been aged at elevated temperatures for times up to 5.7 years. Work on the first, HT-S/710 graphite/polyimide, was started in 1974. Evaluation of the second polyimide, Celion 6000/LARC-160, began in 1980. Baseline properties are presented, including unnotched and notched tensile data as a function of temperature, compression, flexure, shear, and constant-amplitude fatigue data at R = 0.1 and R = -1. Tensile specimens were aged in ovens where pressure and aging temperatures were controlled for various times up to and including 50,000 hours. Changes in tensile strength were determined and plotted as a function of aging time. The HT-S/710 composite aged at 450 F and 550 F if compared to the Celion 6000/LARC-160 composite aged at 350 F and 450 F. After tensile testing, many of the thermal aging specimens were examined using a scanning electron microscope. Results of these studies are presented, and changes in properties and degradation mechanisms during high-temperature aging are discussed and illustrated using metallographic techniques
Rational-spline approximation with automatic tension adjustment
An algorithm for weighted least-squares approximation with rational splines is presented. A rational spline is a cubic function containing a distinct tension parameter for each interval defined by two consecutive knots. For zero tension, the rational spline is identical to a cubic spline; for very large tension, the rational spline is a linear function. The approximation algorithm incorporates an algorithm which automatically adjusts the tension on each interval to fulfill a user-specified criterion. Finally, an example is presented comparing results of the rational spline with those of the cubic spline
Status of carbon sequestration projects in Africa: potential benefits and challenges to scaling up
A general numerical analysis program for the superconducting quasiparticle mixer
A user-oriented computer program SISCAP (SIS Computer Analysis Program) for analyzing SIS mixers is described. The program allows arbitrary impedance terminations to be specified at all LO harmonics and sideband frequencies. It is therefore able to treat a much more general class of SIS mixers than the widely used three-frequency analysis, for which the harmonics are assumed to be short-circuited. An additional program, GETCHI, provides the necessary input data to program SISCAP. The SISCAP program performs a nonlinear analysis to determine the SIS junction voltage waveform produced by the local oscillator. The quantum theory of mixing is used in its most general form, treating the large signal properties of the mixer in the time domain. A small signal linear analysis is then used to find the conversion loss and port impedances. The noise analysis includes thermal noise from the termination resistances and shot noise from the periodic LO current. Quantum noise is not considered. Many aspects of the program have been adequately verified and found accurate
Contact Whiskers for Millimeter Wave Diodes
Several techniques are investigated for making short conical tips on wires (whiskers) used for contacting millimeter-wave Schottky diodes. One procedure, using a phosphoric and chromic acid etching solution (PCE), is found to give good results on 12 microns phosphor-bronze wires. Full cone angles of 60 degrees-80 degrees are consistently obtained, compared with the 15 degrees-20 degrees angles obtained with the widely used sodium hydroxide etch. Methods are also described for cleaning, increasing the tip diameter (i.e. blunting), gold plating, and testing the contact resistance of the whiskers. The effects of the whisker tip shape on the electrical resistance, inductance, and capacitance of the whiskers are studied, and examples given for typical sets of parameters
Development of biaxial test fixture includes cryogenic application
Test fixture has the capability of producing biaxial stress fields in test specimens to the point of failure. It determines biaxial stress by dividing the applied load by the net cross section. With modification it can evaluate materials, design concepts, and production hardware at cryogenic temperatures
Passive and active seismic isolation for gravitational radiation detectors and other instruments
Some new passive and active methods for reducing the effects of seismic disturbances on suspended masses are described, with special reference to gravitational radiation detectors in which differential horizontal motions of two or more suspended test masses are monitored. In these methods it is important to be able to determine horizontal seismic accelerations independent of tilts of the ground. Measurement of changes in inclination of the suspension wire of a test mass, relative to a direction defined by a reference arm of long period of oscillation, makes it possible to carry this out over the frequency range of interest for earth-based gravitational radiation detectors. The signal obtained can then be used to compensate for the effects of seismic disturbances on the test mass if necessary. Alternatively the signal corresponding to horizontal acceleration can be used to move the point from which the test mass is suspended in such a way as to reduce the effect of the seismic disturbance and also damp pendulum motions of the suspended test mass. Experimental work with an active anti-seismic system of this type is described
The energy budget in Rayleigh-Benard convection
It is shown using three series of Rayleigh number simulations of varying
aspect ratio AR and Prandtl number Pr that the normalized dissipation at the
wall, while significantly greater than 1, approaches a constant dependent upon
AR and Pr. It is also found that the peak velocity, not the mean square
velocity, obeys the experimental scaling of Ra^{0.5}. The scaling of the mean
square velocity is closer to Ra^{0.46}, which is shown to be consistent with
experimental measurements and the numerical results for the scaling of Nu and
the temperature if there are strong correlations between the velocity and
temperature.Comment: 5 pages, 3 figures, new version 13 Mar, 200
A Trade Regime for Sub-National Exports Under the Agreement on the Application of Sanitary and Phytosanitary Measures
Regulations relating to disease management have traditionally been an important component of the overall environment in which international trade in agriculture products occurs. The World Trade Organization (WTO) Agreement on the Application of Sanitary and Phytosanitary Measures (SPS Agreement) allows members to restrict or prohibit imports from a country when imported products present a risk to human, animal or plant health or life. As the Bovine Spongiform Encephalopathy (BSE, also commonly called Mad Cow disease in the media) outbreak in Canada showed, the disease status of a country is a major competitive advantage and losing disease-free status can impose significant costs on an industry. The risks associated with SPS-based border closures were not well anticipated by the Canadian industry and government, and little was done in preparation for the potential change in the trading environment and the ensuing losses. This is a mistake many stakeholders in the industry plan to avoid making again.International Relations/Trade,
A Trade Regime for Sub-National Exports Under the Agreement on the Application of Sanitary and Phytosanitary Measures
Regulations relating to disease management have traditionally been an important component of the overall environment in which international trade in agriculture products occurs. The World Trade Organization (WTO) Agreement on the Application of Sanitary and Phytosanitary Measures (SPS Agreement) allows members to restrict or prohibit imports from a country when imported products present a risk to human, animal or plant health or life. As the Bovine Spongiform Encephalopathy (BSE, also commonly called Mad Cow disease in the media) outbreak in Canada showed, the disease status of a country is a major competitive advantage and losing disease-free status can impose significant costs on an industry. The risks associated with SPS-based border closures were not well anticipated by the Canadian industry and government, and little was done in preparation for the potential change in the trading environment and the ensuing losses. This is a mistake many stakeholders in the industry plan to avoid making again.International Relations/Trade,
- …