In situ synchrotron radiation diffraction investigation of the compression behaviour at 350 °C of ZK40 alloys with addition of CaO and Y

The evolution of the microstructure during compression is investigated with in situ synchrotron radiation diffraction in as-cast ZK40, ZK40-2CaO and ZK40-1Y Mg alloys. The specimens were compressed at 350 °C with a strain rate of 10−3 s−1 until 30% deformation. The Y containing alloy showed the highest 0.2% proof strength in compression of 35 MPa at 350 °C which is double that of the ZK40 alloy, while the CaO added alloy shows a moderate increment at 23 MPa. The Y containing alloy shows some work hardening, while the CaO modified and the ZK40 alloys do not show work hardening after yield. Synchrotron radiation diffraction timelines show that continuous and discontinuous dynamic recrystallization occurs during deformation of the ZK40 alloy while a small amount of dynamic recrystallization was observed in the ZK40-1Y alloy. However, dynamic recrystallization was not present in the ZK40-2CaO alloy. SEM-EBSD analysis conducted on the deformed samples shows a significantly high volume fraction of twins in the Y and CaO containing alloys which was absent in the ZK40 alloy. The modified deformation behaviours observed in the CaO and Y containing alloys were attributed to the presence of intermetallic particles found at the grain boundaries and to the role of Ca and Y in stabilising twinning.The authors acknowledge the Deutsches Elektronen-Synchro-tron for the provision of facilities within the framework of proposal I-20130434.RHBacknowledgesUniversityofSãoPaulofor granting the fellowship 'Bolsa Empreendedorismo'

On the influence of solution and ageing treatments on the microstructure of ZK40 alloys modified with Ca, Gd, Nd and y additions

Abstract As-cast ZK40 alloys, modified with the addition of CaO, Gd, Nd and Y were investigated. Solution heat treatments were performed based on differential thermal analysis results. The unmodified ZK40 alloy exhibited microstructure with nearly no intermetallic compound but with precipitates formed during the solution treatment. The modified ZK40 alloys exhibited a semi-dissolved network of intermetallic compounds along the grain boundaries and zones of intermetallic compounds within the grains. Interestingly, no precipitates were observed immediately next to the grain boundaries. The energy dispersive X-ray spectroscopy line scans showed an enrichment of Zn and Zr in the regions where the precipitates are found, suggesting that they are Zn-Zr precipitates. The ageing behaviour was compared between the as-cast and the solution treated materials and it was found that apart from the ZK40-Gd, ZK40-Nd and ZK40-Y aged at 200 °C after solution treatment, there is no notable ageing response for the investigated alloys.</jats:p

Thixomolded AZ91D and MRI153M magnesium alloys and their enhanced corrosion resistance

© 2020 The Authors. Materials and Corrosion published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim AZ91D and MRI153M alloys were produced by thixomolding. Their corrosion resistance is significantly higher than that of similar materials produced by ingot or die-casting. A corrosion rate smaller than 0.2 mm/year in 5 wt% NaCl solution is measured for the thixomolded AZ91D alloy. The corrosion behaviour was evaluated using immersion tests, electrochemical impedance spectroscopy, hydrogen evolution, glow discharge optical emission spectroscopy, and atomic emission spectroelectrochemistry. A bimodal microstructure is observed for both alloys, with the presence of coarse primary α-Mg grains, fine secondary α-Mg grains, β-phase, and other phases with a minor volume fraction. The amount of coarse primary α-Mg is significantly higher for the AZ91D compared with the MRI153M. The network of β-phase around the fine secondary α-Mg grains is better established in the thixomolded AZ91D alloy. A combination of several factors such as the ratio of primary to secondary α-Mg grains, localised corrosion or barrier effect due to other phases, as well as regions of preferential dissolution of the α-Mg due to chemical segregation, are thought to be responsible for the high corrosion resistance exhibited by the thixomolded AZ91D and MRI153M.German Ministry of Education and Research; Christian Doppler Societ

Heusler type CoNiGa alloys with high martensitic transformation temperature

A strong need exists to develop new kinds of high-temperature shape-memory alloys. In this study, two series of CoNiGa alloys with different compositions have been studied to investigate their potentials as high-temperature shape-memory alloys, with regard to their microstructure, crystal structure, and martensitic transformation behavior. Optical observations and X-ray diffractions confirmed that single martensite phase was present for low cobalt samples, and dual phases containing martensite and gamma phase were present for high cobalt samples. It was also found that CoNiGa alloys in this study exhibit austenitic transformation temperatures higher than 340 degrees C, showing their great potentials for developing as high-temperature shape-memory alloys

Thermal cycling of Mg-MMCs

Creep resistant Mg alloy QE22 reinforced with maftec(R), saffil(R) or supertec(R) short fibres is cycled between room temperature and 308degreesC at different ramp rates in the longitudinal and transverse directions. From the careful analysis of the strain vs. temperature thermal cycling curves true material behaviour and artifacts from the dilatometer are deciphered. From this analysis true coefficient of thermal expansion and relaxation processes are deduced. Hysteresis at higher temperatures is attributed to the relaxation process, whereas hysteresis at low temperatures giving a tilt-ground shape to the thermal cycling curves is again an artifact due to the instrument. The change in ramp rate highlights this effect. Finally, the effect of thermal cycling on microstructure is examined

Interrupted creep behaviour of Mg alloys developed for powertrain applications

A conventional magnesium alloy, AZ91D, and two creep resistant magnesium alloys, developed for powertrain applications, MRI 153M and MRI 230D, are prepared by high pressure die casting. These alloys are tested for their creep behaviour in the continuous manner, as is the Current practice, and in the interrupted manner, which represents the real life Situation more closely. It is observed that the interrupted creep tests give rise to a primary creep appearing at the beginning of each cycle resulting in a higher average strain rate than that encountered in the continuous creep tests. Further, the shorter the cycle time, higher is the average strain rate in the interrupted creep tests. A higher average strain rate will give rise to a higher strain over the same period. This is attributed to the recovery taking place during the cooling and heating between two cycles. The effect of additional precipitation during interrupted creep tests depends on the nature of the precipitates. The additional precipitation of beta phase during the cooling and heating between two cycles increases the steady state strain rate in the AZ91D and MRI 153M alloys. whereas the additional precipitation of C36 phase during the cooling and heating between two cycles decreases the steady state strain rate in the MRI 230D alloy. (C) 2009 Elsevier B.V. All rights reserved