Observed and Expected Incidence of Cervical Cancer in Lusaka and the Southern and Western Provinces of Zambia, 2007 - 2012

Objectives—Cervical cancer is increasing but underestimated in developing countries. We calculated the observed and expected incidence of cervical cancer in Lusaka and Southern and Western provinces of Zambia. Methods/Materials—Data for 2007-2012 was obtained for the 3 provinces. Data included age, residence, year of diagnosis, marital status, occupation, HIV, stage, radiotherapy and chemotherapy. Expected incidence in Southern and Western provinces was calculated based on observed incidence for Lusaka province, adjusting for HIV. Results—Crude and age-standardized incidence rates (ASR) in Lusaka were 2-4 times higher than incidence in the other 2 provinces. Lusaka had a rate of 54.1/105 and ASR of 82.1/105 in the age group 15-49. The Southern province had a rate of 17.1/105 and ASR of 25.5/105; Western province rate of 12.3/105 and ASR rate of 17.2/105. The observed cervical cancer incidence rates in the Southern and Western provinces were lower than the rate in Lusaka, possibly due to the uncertainty of underreporting/under-diagnosis or actual lower risk for reasons yet unclear. HIV seroprevalence rate in patients from the 3 provinces were 46 – 93% higher than seroprevalence in the respective general populations. Conclusion—Cervical cancer is significantly underestimated in Zambia and HIV has a significant role in pathogenesis. Future studies should establish methods for case ascertainment and better utilization of hospital- and population-based registries in Zambia and other similar developing countries

“I see salt everywhere”: A qualitative examination of the utility of arts-based participatory workshops to study noncommunicable diseases in Tanzania and Malawi.

The burden of noncommunicable diseases (NCDs) including hypertension, diabetes, and cancer, is rising in Sub-Saharan African countries like Tanzania and Malawi. This increase reflects complex interactions between diverse social, environmental, biological, and political factors. To intervene successfully, new approaches are therefore needed to understand how local knowledges and attitudes towards common NCDs influence health behaviours. This study compares the utility of using a novel arts-based participatory method and more traditional focus groups to generate new understandings of local knowledges, attitudes, and behaviours towards NCDs and their risk factors. Single-gender arts-based participatory workshops and focus group discussions were conducted with local communities in Tanzania and Malawi. Thematic analysis compared workshop and focus group transcripts for depth of content and researcher-participant hierarchies. In addition, semiotic analysis examined the contribution of photographs of workshop activities to understanding participants’ experiences and beliefs about NCD risk factors. The arts-based participatory workshops produced in-depth, vivid, emotive narratives of participants’ beliefs about NCDs and their impact (e.g., “… it spreads all over your body and kills you—snake’s poison is similar to diabetes poison”), while the focus groups provided more basic accounts (e.g., “diabetes is a fast killer”). The workshops also empowered participants to navigate activities with autonomy, revealing their almost overwhelmingly negative beliefs about NCDs. However, enabling participants to direct the focus of workshop activities led to challenges, including the perpetuation of stigma (e.g., comparing smells associated with diabetes symptoms with sewage). Semiotic analysis of workshop photographs provided little additional insight beyond that gained from the transcripts. Arts-based participatory workshops are promising as a novel method to inform development of culturally relevant approaches to NCD prevention in Tanzania and Malawi. Future research should incorporate more structured opportunities for participant reflection during the workshops to minimise harm from any emerging stigma

Where Are All the Mycobacterium avium Subspecies paratuberculosis in Patients with Crohn's Disease?

Mycobacterium avium subspecies paratuberculosis (MAP) causes a chronic granulomatous inflammation of the intestines, Johne's disease, in dairy cows and every other species of mammal in which it has been identified. MAP has been identified in the mucosal layer and deeper bowel wall in patients with Crohn's disease by methods other than light microscopy, and by direct visualization in small numbers by light microscopy. MAP has not been accepted as the cause of Crohn's disease in part because it has not been seen under the microscope in large numbers in the intestines of patients with Crohn's disease. An analysis of the literature on the pathology of Crohn's disease and on possible MAP infection in Crohn's patients suggests that MAP might directly infect endothelial cells and adipocytes and cause them to proliferate, causing focal obstruction within already existing vessels (including granuloma formation), the development of new vessels (neoangiogenesis and lymphangiogenesis), and the “creeping fat” of the mesentery that is unique in human pathology to Crohn's disease but also occurs in bovine Johne's disease. Large numbers of MAP might therefore be found in the mesentery attached to segments of intestine affected by Crohn's disease rather than in the bowel wall, the blood and lymphatic vessels running through the mesentery, or the mesenteric fat itself. The walls of fistulas might result from the neoangiogenesis or lymphangiogenesis that occurs in the bowel wall in Crohn's disease and therefore are also possible sites of large numbers of MAP. The direct visualization of large numbers of MAP organisms in the tissues of patients with Crohn's disease will help establish that MAP causes Crohn's disease

Observed and Expected Incidence of Cervical Cancer in Lusaka and the Southern and Western Provinces of Zambia, 2007 - 2012

Objectives—Cervical cancer is increasing but underestimated in developing countries. We calculated the observed and expected incidence of cervical cancer in Lusaka and Southern and Western provinces of Zambia. Methods/Materials—Data for 2007-2012 was obtained for the 3 provinces. Data included age, residence, year of diagnosis, marital status, occupation, HIV, stage, radiotherapy and chemotherapy. Expected incidence in Southern and Western provinces was calculated based on observed incidence for Lusaka province, adjusting for HIV. Results—Crude and age-standardized incidence rates (ASR) in Lusaka were 2-4 times higher than incidence in the other 2 provinces. Lusaka had a rate of 54.1/105 and ASR of 82.1/105 in the age group 15-49. The Southern province had a rate of 17.1/105 and ASR of 25.5/105; Western province rate of 12.3/105 and ASR rate of 17.2/105. The observed cervical cancer incidence rates in the Southern and Western provinces were lower than the rate in Lusaka, possibly due to the uncertainty of underreporting/under-diagnosis or actual lower risk for reasons yet unclear. HIV seroprevalence rate in patients from the 3 provinces were 46 – 93% higher than seroprevalence in the respective general populations. Conclusion—Cervical cancer is significantly underestimated in Zambia and HIV has a significant role in pathogenesis. Future studies should establish methods for case ascertainment and better utilization of hospital- and population-based registries in Zambia and other similar developing countries

Micro-Injection Moulding of Polymer Microfluidic Devices

Microfluidic devices have several applications in different fields, such as chemistry, medicine and biotechnology. Many research activities are currently investigating the manufacturing of integrated microfluidic devices on a mass- production scale with relatively low costs. This is especially important for applications where disposable devices are used for medical analysis. Micromoulding of thermoplastic polymers is a developing process with great potential for producing low-cost microfluidic devices. Among different micromoulding techniques, micro-injection moulding is one of the most promising processes suitable for manufacturing polymeric disposable microfluidic devices. This review paper aims at presenting the main significant developments that have been achieved in different aspects of micro-injection moulding of microfluidic devices. Aspects covered include device design, machine capabilities, mould manufacturing, material selection and process parameters. Problems, challenges and potential areas for research are highlighted