Measurement of Decay Time Constant of Shielding Current in ITER-TF Joint Samples

Joint sample tests have been carried out as a qualification test for ITER Toroidal Field (TF) coils. The joint sample comprises two short TF conductors that have "twin-box" joint terminals at both ends. The lower joint is a testing part that is a full size joint of the TF coils. Hall probes are attached on the lower joint box at around the center of the external field coil of the test facility. The magnetic field induced by shielding currents in the joint can be estimated from the difference between the measured magnetic field strength and the magnetic field generated by the external field coil. The magnetic field by the shielding currents during shut-off of the external field coil from -1.0 T is evaluated for six samples. The decay time constants of the shielding currents are gradually elongated with decrease of the shielding currents in all the samples. In comparison with simulation results, it is considered that the main shielding current flows in superconducting cables in the two conductors with crossing the jointed plane and that the joint resistance is decreased at low total current

Evaluation of ITER TF Coil Joint Performance

To evaluate the ITER TF joint performance, the joint test sample, which consists of two short TF conductors and has full size joint, shall be tested using NIFS test facility under the condition of current of 68 kA and external field of 2 T. For high accuracy, the issue of voltage difference between cable and jacket had been anticipated in the evaluation of joint resistance. If a voltage difference exist between them, it is difficult to measure real joint resistance using voltage taps on the jacket. Therefore, the author first calculated the position where voltage of cable and jacket become equipotential and then decided the voltage tap position where the influence of voltage drop could be avoided. Thus, a high accuracy measurement of joint resistance could be achieved and the joint resistance was accurately evaluated as around 1 n Ω , which is well below the ITER requirement of 3 n Ω

Test of ITER-TF Joint Samples With NIFS Test Facilities

Qualification tests of the ITER toroidal field (TF) conductor joints have been carried out by testing joint samples with test facilities in the National Institute for Fusion Science, NINS, Toki, Japan. The joint sample consists of two short TF conductors with the length of 1535 mm, which is restricted by the test facility with 9-T split coils and 100-kA current leads. The sample current is supplied from a dc 75-kA power supply. Each conductor has two joint boxes at both terminals. The lower joint is a testing part that is a full-size joint of the TF coil. The joint resistance of the lower joint is estimated from the increase of the average voltage drop among the six taps on the conductor against the currents. Five joint samples were tested until 2016, and all the samples satisfied the requirement of the joint resistance at less than 3 nΩ. The method of the measurement and the results are summarized, and the voltage distribution among the voltage taps is discussed

Results of All ITER TF Full-Size Joint Sample Tests in Japan

Nine toroidal field (TF) coils have been developed in Japan for the international thermonuclear experimental reactor (ITER). The joint resistance of TF coil should satisfy the requirement of smaller than 3 nano-ohm at 2 T of external magnetic field and 68 kA of transport current. Full-size joint sample (FSJS) tests were performed for joint development and for TF coil manufacture, as part of the process control. 11 FSJS tests are conducted in total. FSJS tests were conducted with assistance from a test faculty in the National Institute for Fusion Science as reported in a previous paper. All FSJS tests successfully satisfied the requirement of resistance less than 3 nΩ at 2 T. Additionally, the TF coil joints are subjected to cyclic electromagnetic force and warm-up/cool-down during the ITER operation. The authors investigated the joint performance for the abovementioned influence. The results showed no degradation in the joint resistance. Thus, the TF joint developed in Japan was qualified successfully

Comparative genome and transcriptome analyses of the social amoeba Acytostelium subglobosum that accomplishes multicellular development without germ-soma differentiation

Background Social amoebae are lower eukaryotes that inhabit the soil. They are characterized by the construction of a starvation-induced multicellular fruiting body with a spore ball and supportive stalk. In most species, the stalk is filled with motile stalk cells, as represented by the model organism Dictyostelium discoideum, whose developmental mechanisms have been well characterized. However, in the genus Acytostelium, the stalk is acellular and all aggregated cells become spores. Phylogenetic analyses have shown that it is not an ancestral genus but has lost the ability to undergo cell differentiation. Results We performed genome and transcriptome analyses of Acytostelium subglobosum and compared our findings to other available dictyostelid genome data. Although A. subglobosum adopts a qualitatively different developmental program from other dictyostelids, its gene repertoire was largely conserved. Yet, families of polyketide synthase and extracellular matrix proteins have not expanded and a serine protease and ABC transporter B family gene, tagA, and a few other developmental genes are missing in the A. subglobosum lineage. Temporal gene expression patterns are astonishingly dissimilar from those of D. discoideum, and only a limited fraction of the ortholog pairs shared the same expression patterns, so that some signaling cascades for development seem to be disabled in A. subglobosum. Conclusions The absence of the ability to undergo cell differentiation in Acytostelium is accompanied by a small change in coding potential and extensive alterations in gene expression patterns