25,874 research outputs found
Multiple environment materials test chamber having a multiple port X-ray tube for irradiating a plurality of samples Patent
Multisample test chamber for exposing materials to X rays, temperature change, and gaseous conditions and determination of material effect
Multiple test chamber exposes materials to various environments
Multiple compartment test chamber exposes several material specimens to various environmental conditions for prolonged periods. The specimens are individually mounted in chamber compartments, rotated to various positions, and measured through optical windows to determine progressive changes in the material properties
Effect of cyclic conditions on the dynamic oxidation of gas turbine superalloys
The effects of operating parameters of a dynamic apparatus used to study oxidation and thermal fatigue of gas turbine materials were studied. IN-100, TD-NiCr, and WI-52 were tested at a maximum temperature of 1,090 deg C. Heating time per cycle was varied from 1/20 hr to 10 hr. Minimum temperatures between heating cycles were room temperature, 430 deg, and 650 deg C. Cooling air velocities were zero, Mach 0.7, and Mach 1. Increasing the number of cycles for a given time at temperature increased weight loss. Thermal fatigue was related to number of cycles more than to time at temperature
Polydimethylsiloxane based microfluidic diode
In this paper, we present a novel elastomer-based microfluidic device for rectifying flow. The device is analogous to an electronic diode in function since it allows flow in one direction and stops flow in the opposing direction. The device is planar, in-line and can be replica molded via standard soft lithography techniques. The fabrication process is outlined in detail and follows a simple procedure that requires only photolithography and one replica molding step. Several geometries of devices are presented along with their flow versus pressure characteristics. A brief discussion of the device behavior is presented along with possible uses for the device
Optical Turbulence Measurements and Models for Mount John University Observatory
Site measurements were collected at Mount John University Observatory in 2005
and 2007 using a purpose-built scintillation detection and ranging system.
profiling indicates a weak layer located at 12 - 14 km above sea
level and strong low altitude turbulence extending up to 5 km. During calm
weather conditions, an additional layer was detected at 6 - 8 km above sea
level. profiling suggests that tropopause layer velocities are nominally
12 - 30 m/s, and near-ground velocities range between 2 -- 20 m/s, dependent on
weather. Little seasonal variation was detected in either and
profiles. The average coherence length, , was found to be cm for
the full profile at a wavelength of 589 nm. The average isoplanatic angle,
, was arcsec. The mean turbulence altitude,
, was found to be km above sea level. No average in the
Greenwood frequency, , could be established due to the gaps present in the
\vw\s profiles obtained. A modified Hufnagel-Valley model was developed to
describe the profiles at Mount John, which estimates at 6 cm
and at 0.9 arcsec. A series of models were developed, based
on the Greenwood wind model with an additional peak located at low altitudes.
Using the model and the suggested model for moderate ground
wind speeds, is estimated at 79 Hz.Comment: 14 pages; accepted for publication in PAS
Automated mixed traffic vehicle design AMTV 2
The design of an improved and enclosed Automated Mixed Traffic Transit (AMTT) vehicle is described. AMTT is an innovative concept for low-speed tram-type transit in which suitable vehicles are equipped with sensors and controls to permit them to operate in an automated mode on existing road or walkway surfaces. The vehicle chassis and body design are presented in terms of sketches and photographs. The functional design of the sensing and control system is presented, and modifications which could be made to the baseline design for improved performance, in particular to incorporate a 20-mph capability, are also discussed. The vehicle system is described at the block-diagram-level of detail. Specifications and parameter values are given where available
Development of satisfactory lateral- directional handling qualities in the landing approach
Developing lateral stability and directional control handling qualities in landing approach control of aircraf
Preparing composite materials from matrices of processable aromatic polyimide thermoplastic blends
Composite materials with matrices of tough, thermoplastic aromatic polyimides are obtained by blending semi-crystalline polyimide powders with polyamic acid solutions to form slurries, which are used in turn to prepare prepregs, the consolidation of which into finished composites is characterized by excellent melt flow during processing
- …