A study of effects of a new agricultural-based deicer on the properties of pavement concrete

This study was aimed at evaluating effects of a new agricultural-based deicer named by the manufacturer as Season I on the properties of pavement concrete and its performance was compared with two traditional deicing salts: sodium chloride (NaCl) and calcium chloride (CaCl2). The study can be divided into three parts and the first part evaluated physical frost damage including scaling and structural degradation of concrete/mortar. Strength loss, mass loss and scaling rating due to the damage were given. The second part inspected the effects of deicers on surface skid resistance and concrete permeability. The skid resistance indicator, BPN, and indirect concrete permeability indicators including electrical resistivity, air permeability index and water absorption rate were tested in this part. In the last part, the results of EDS point analyses were presented and discussed. The goal was to identify change/damage, if any, of micro-structures caused by the penetration of deicers. The results of this study indicate NaCl and CaCl2 solutions caused worse scaling and structural degradation comparing with Season I. Application of Season I greatly reduced the skid resistance comparing with NaCl and CaCl2 solutions which had no apparent impacts. Season I reduced concrete permeability comparing with NaCl and CaCl2 solutions based on electrical resistivity and water absorption rate. The EDS analyses found penetration depth of Season I was 13 mm and the penetration depth of NaCl was 19 mm. No salt precipitate or micro-structure change was found

Interference mitigation for a joint radar communication system based on the FrFT for automotive applications

In multi user scenarios to prevent interference between users that share the same bandwidth at the same time,each user has to transmit wave forms that are uncorrelated with those of other users. However, due to spectrum limitations, the uncorrelated property cannot always be satisfied meaning that interference is unavoidable. In order to alleviate the interference, a framework for interference mitigation is presented. The performance of the proposed framework is tested on simulated and real signals. The real signal is acquired in a controlled laboratory environment using a Software Defined Radio (SDR). The simulated and experimental results show that the proposed framework is capable of mitigating the interference from other users

Correlation between porosity, amorphous phase and CMAS corrosion behaviour of LaMgAl11O19 thermal barrier coatings

Calcium-magnesium-alumino-silicate (CMAS) attack is one of the significant failure mechanisms of thermal barrier coatings (TBCs), which can facilitate TBC’s degradation at elevated temperatures. To clarify the correlation between the porosity, CMAS corrosion behaviour, lanthanum magnesium hexaluminate (LaMgAl11O19, LMA) TBCs were prepared by atmospheric plasma spraying (APS) and then heat-treated at 1173K and 1523K, respectively. For comparison, LMA tablets were prepared by mechanical and cold isostatic pressing. CMAS attack at 1523K was carried out both for LMA tablets and LMA coatings. Their microstructure, phase composition, and crystallization behavior after CMAS attack were investigated using scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS), X-ray diffraction as well as differential scanning calorimetry (DSC). The results indicated that CMAS attack was arrested for LMA tablets due to the formation of a dense crystalline layer induced by the chemical interactions between LMA and CMAS glass, while the as-sprayed LMA coatings were completely penetrated by molten CMAS due to the presence of amorphous phase and connected pores. Although the isothermal heat-treatment promoted a crystallization of LMA coatings, much vertical cracks formed during heat-treatment. The heat-treated LMA coatings suffered a severer CMAS attack than the as-sprayed one, since the vertical cracks inevitably provided efficient infiltration paths for molten CMAS

Thermal barrier coatings on polymer materials

Polyimide matrix composite (PIMC) has been widely used to replace metallic parts due to its low density and high strength. It is considered as an effective approach to improve thermal oxidation resistance, operation temperature and lifetime of PIMC by depositing a protection coating. The objective of the research was to fabricate a series of thermal barrier coatings (TBCs) on PIMC by a combined sol-gel/sealing treatment process and air plasma spraying (APS). By optimizing the experimental parameters, thermal shock resistance, thermal oxidation resistance and thermal ablation resistance of PIMC could be improved significantly. The ZrO2 sol was prepared by sol-gel process and the effects of the different organic additions on phase structure, crystallite size and crystal growth behavior of the ZrO2 nanocrystallite were investigated. The addition of HAc and DMF were beneficial to decrease the crystallite size and alter the activation energy for crystal growth, further inducing the crystallization of ZrO2 nanocrystallite at low temperature (300ºC) and the stability of tetragonal ZrO2 at 600ºC. Based on the optimized parameters of the sol preparation, the ZrO2/phosphates duplex coating was fabricated on PIMC via a combined sol-gel and sealing treatment process. The sealing mechanism of the phosphates in the duplex coating was primarily attributed to the adhesive binding of the phosphates and the chemical bonding between the sealant and the coating. It was demonstrated that the duplex coating exhibited excellent thermal shock resistance and no apparent delamination or spallation occurred. Relatively, the duplex coating with the thickness of 150 μm provided excellent thermal oxidation and thermal ablation resistance for the polymer substrate. However, the presence of cracks and delamination in the coatings provided the channels for oxygen diffusion, causing the final failure of the protection coating. Figure 4 – TBCs on CFPI The Zn/YSZ and Al/YSZ coating systems were successfully deposited on PIMC by APS. Metals with comparatively low melting point as the bond coats (Cu, Al, Zn) were beneficial to increase thermal shock resistance of the coating systems. In comparison with the Al/YSZ coating system, the Zn/YSZ coating exhibited the better thermal shock resistance, which was ascribable to the lower residual stress in the Zn layer after deposition and the lower thermal stress induced during thermal shock test. For these coatings, the increase in surface toughness of the substrate as well as the decrease in thickness of metal layer favored the improvement of thermal shock resistance of the coatings. With the temperature increases, thermal shock lifetime of the coatings decreased disastrously. However, the difference was that the slight increase of the thickness of YSZ layer favored the increase in thermal shock resistance of the Al/YSZ coatings, while for the Zn/YSZ coating systems the increase in the thickness of YSZ layer made thermal shock resistance weaken. Owing to the protection of Zn/YSZ and Al/YSZ coating systems, the time for 5 wt% weight loss of the sample was prolonged from 16 h to 50 h when oxidation at 400ºC; as the oxidation temperature increased to 450ºC, the time for 5wt% weight loss was extended from 5 h to 13 h. By depositing different coatings, the anti-ablation property of PIMC was significantly improved. During property testing, the formation of cracks and delamination in the coating and the occurrence of the spallation led to the failure of the coating systems, which was mainly due to the residual stress during the deposition process, thermal stress induced by the mismatch in thermal expansion coefficient and further oxidation of the substrate. Please click Additional Files below to see the full abstract

Molecular subtypes based on centrosome-related genes can predict prognosis and therapeutic responsiveness in patients with low-grade gliomas

BackgroundAbnormalities in centrosome regulatory genes can induce chromosome instability, cell differentiation errors, and tumorigenesis. However, a limited number of comprehensive analyses of centrosome-related genes have been performed in low-grade gliomas (LGG).MethodsLGG data were extracted from The Cancer Genome Atlas (TCGA) and Chinese Glioma Genome Atlas (CGGA) databases. The ConsensusClusterPlus” R package was used for unsupervised clustering. We constructed a centrosome-related genes (CRGs) signature using a random forest model, lasso Cox model, and multivariate Cox model, and quantified the centrosome-related risk score (centS). The prognostic prediction efficacy of centS was evaluated using a Receiver Operating Characteristic (ROC) curve. Immune cell infiltration and genomic mutational landscapes were evaluated using the ESTIMATE algorithm, single-sample Gene Set Enrichment Analysis (ssGSEA) algorithm, and “maftools” R package, respectively. Differences in clinical features, isocitrate dehydrogenase (IDH) mutation, 1p19q codeletion, O6-methylguanine-DNA methyltransferase promoter (MGMTp) methylation, and response to antitumor therapy between the high- and low-centS groups were explored. “pRRophetic” R packages were used for temozolomide (TMZ) sensitivity analysis. qRT-PCR verified the differential expression of the centrosomal gene team, the core of which is CEP135, between LGG cells and normal cells.ResultsTwo distinct CRG-based clusters were identified using consensus unsupervised clustering analysis. The prognosis, biological characteristics, and immune cell infiltration of the two clusters differed significantly. A well-performing centS signature was developed to predict the prognosis of patients with LGG based on 12 potential CRGs. We found that patients in the high-centS group showed poorer prognosis and lower proportion of IDH mutation and 1p19q codeletion compared to those in the low-centS group. Furthermore, patients in the high-centS group showed higher sensitivity to TMZ, higher tumor mutation burden, and immune cell infiltration. Finally, we identified a centrosomal gene team whose core was CEP135, and verified their differential expression between LGG cells and normal glial cells.ConclusionOur findings reveal a novel centrosome-related signature for predicting the prognosis and therapeutic responsiveness of patients with LGG. This may be helpful for the accurate clinical treatment of LGG