51,330 research outputs found
Hollow rolling element bearings
A low mass rolling element with a lightweight core and hollow center was developed for use in bearings. The core is plated so as to provide a hard surface and increase the life and reliability of the high speed ball bearings
Large-bore tapered-roller bearing performance and endurance to 2.4 million DN
The operating characteristics and experimental life estimates for 120.65 mm bore tapered roller bearings of two designs under combined radial and thrust loads were determined. A modified standard bearing design was tested at speeds up to 15,000 rpm. A computer optimized, high speed design was tested at speeds up to 20,000 rpm. Both designs were tested at a combined load of 26,700 N (6000 lb) radial load and and 53,400 N (12,000 lb) thrust load. Advanced helicopter transmissions which require the higher-speed capability of tapered-roller bearings also require higher temperature capability (ref. 2). Thus, materials with temperature capabilities higher than the conventional carburizing steels are required
Rolling-element fatigue lives of AISI 52100 steel balls with several synthetic lubricants
Rolling-element fatigue tests were run with three synthetic lubricants with and without antiwear additives and with a paraffinic mineral oil at race temperatures of 336 to 353 K (146 146 to 175 F). The five-ball fatigue tester was used with steel balls to evaluate the relative fatigue lives with each of six lubricant-additive combinations. The tests were run at 5,520 MPa (800,000psi) maximum Hertz stress, 10,000 rpm shaft speed, and 30 deg contact angle. The lubricants tested have similar kinetic viscosities at 372 K (210 F) ranging from 0.034 to 0.089 sq cm/sec (3.4 to 8.9 cS). At these conditions, the mode of failure in the five-ball fatigue tester was classical subsurface rolling-element fatigue. The baseline for comparison of fatigue life was the paraffinic mineral oil without additives. The effects of the synthetic lubricants and their additives, which are useful for boundary lubrication, oxidation or foam inhibition, were evaluated
Lubrication of rolling-element bearings
The lubrication of rolling element bearings is surveyed. Emphasis is on the critical design aspects related to speed, temperature, and ambient pressure environment. Types of lubrication including grease, jets, mist, wick, and through the race are discussed. The historical development, present state of technology, and the future problems of rolling element bearing lubrication are discussed
Comparison of predicted and experimental thermal performance of angular-contact ball bearings
Predicted bearing heat generation and bearing temperature were verified by experimental data for ball bearings over a range of sizes, shaft speeds, and lubricant flow rates. The computer program Shaberth requires, as input, a factor which describes the air-oil mixture in the bearing cavity for calculation of the ball drag contribution to bearing heat generation. An equation for this lubricant percent volume in the bearing cavity was derived and appears to be valid over the range of test conditions including bearing bore sizes from 35 to 167 mm and shaft speeds from 1.0 to 3.0 million DN
Rolling-element fatigue life of AMS 5900 balls
The rolling-element fatigue life of AMS 5900 12.7-mm (1/2-in.) dia was determined in five-ball fatigue testers. The 10% life with the warm headed AMS 5900 balls was equivalent to that of AMS 5749 and over eight times that of AISI M-50. The AMS balls fabricated by cold heading had small surface cracks which initiated fatigue spalls where these cracks were crossed by running tracks. The cold-headed AMS 5900 balls had a 10% fatigue life an order of magnitude less than that of the warm headed balls even when failures on the cold headed balls at visible surface cracks were omitted
Flexible fire retardant polyisocyanate modified neoprene foam
Lightweight, fire resistant foams have been developed through the modification of conventional neoprene-isocyanate foams by the addition of an alkyl halide polymer. Extensive tests have shown that the modified/neoprene-isocyanate foams are much superior in heat protection properties than the foams heretofore employed both for ballistic and ablative purposes
Modified polyurethane foams for fuel-fire Patent
Modification of polyurethanes with alkyl halide resins, inorganic salts, and encapsulated volatile and reactive halogen for fuel fire contro
Fire retardant polyisocyanurate foam
Fire retardant properties of low density polymer foam are increased. Foam has pendant nitrile groups which form thermally-stable heterocyclic structures at temperature below degradation temperature of urethane linkages
Effect of double vacuum melting and retained austenite on rolling-element fatigue life of AMS 5749 bearing steel
AMS 5749 steel combines the tempering, hot hardness, and hardness retention characteristics of AISI M-50 steel with the corrosion and oxidation resistance of AISI 440C stainless steel. The five-ball fatigue tester was used to evaluate the rolling-element fatigue life of AMS 5749. Double vacuum melting (vacuum induction melting plus vacuum arc remelting, VIM-VAR) produced AMS 5749 material with a rolling-element fatigue life at least 14 times that of vacuum induction melting alone. The VIM-VAR AMS 5749 steel balls gave lives from 6 to 12 times greater than VIM-VAR AISI M-50 steel balls. The highest level of retained austenite, 14.6 percent, was significantly detrimental to rolling-element fatigue life relative to the intermediate level of 11.1 percent
- …