Prospective Analysis Spin- and CP-sensitive Variables in H -> ZZ -> l_1 l_1 l_2 l_2 with Atlas

A possibility to prove spin and CP-eigenvalue of a Standard Model (SM) Higgs boson is presented. We exploit angular correlations in the subsequent decay H -> ZZ -> 4l (muons or electrons) for Higgs masses above 200 GeV. We compare the angular distributions of the leptons originating from the SM Higgs with those resulting from decays of hypothetical particles with differing quantum numbers. We restrict our analysis to the use of the Atlas-detector which is one of two multi-purpose detectors at the upcoming 14 TeV proton-proton-collider (LHC) at CERN. By applying a fast simulation of the Atlas detector it can be shown that these correlations will be measured sufficiently well that consistency with the spin-CP hypothesis 0+ of the Standard Model can be verified and the 0- and 1+- can be ruled out with an integrated luminosity of 100 fb^-1.Comment: 25 pages, 9 figures Version 2: Minor changes made as requested by Atlas referee and Springer editor. Added a chapter where background subtraction is detaile

Simulation verification techniques study. Subsystem simulation validation techniques

Techniques for validation of software modules which simulate spacecraft onboard systems are discussed. An overview of the simulation software hierarchy for a shuttle mission simulator is provided. A set of guidelines for the identification of subsystem/module performance parameters and critical performance parameters are presented. Various sources of reference data to serve as standards of performance for simulation validation are identified. Environment, crew station, vehicle configuration, and vehicle dynamics simulation software are briefly discussed from the point of view of their interfaces with subsystem simulation modules. A detailed presentation of results in the area of vehicle subsystems simulation modules is included. A list of references, conclusions and recommendations are also given

Simulation verification techniques study: Simulation performance validation techniques document

Techniques and support software for the efficient performance of simulation validation are discussed. Overall validation software structure, the performance of validation at various levels of simulation integration, guidelines for check case formulation, methods for real time acquisition and formatting of data from an all up operational simulator, and methods and criteria for comparison and evaluation of simulation data are included. Vehicle subsystems modules, module integration, special test requirements, and reference data formats are also described

A Damping of the de Haas-van Alphen Oscillations in the superconducting state

Deploying a recently developed semiclassical theory of quasiparticles in the superconducting state we study the de Haas-van Alphen effect. We find that the oscillations have the same frequency as in the normal state but their amplitude is reduced. We find an analytic formulae for this damping which is due to tunnelling between semiclassical quasiparticle orbits comprising both particle-like and hole-like segments. The quantitative predictions of the theory are consistent with the available data.Comment: 7 pages, 5 figure

Large-area sheet task: Advanced dendritic-web-growth development

Thermally generated stresses in the growing web crystal were reduced. These stresses, which if too high cause the ribbon to degenerate, were reduced by a factor of three, resulting in the demonstrated growth of high-quality web crystals to widths of 5.4 cm. This progress was brought about chiefly by the application of thermal models to the development of low-stress growth configurations. A new temperature model was developed which can analyze the thermal effects of much more complex lid and top shield configurations than was possible with the old lumped shield model. Growth experiments which supplied input data such as actual shield temperature and melt levels were used to verify the modeling results. Desirable modifications in the melt level-sensing circuitry were made in the new experimental web growth furnace, and this furnace has been used to carry out growth experiments under steady-state conditions. New growth configurations were tested in long growth runs at Westinghouse AESD which produced wider, lower stress and higher quality web crystals than designs previously used

Automorphisms of Partially Commutative Groups II: Combinatorial Subgroups

We define several "standard" subgroups of the automorphism group Aut(G) of a partially commutative (right-angled Artin) group and use these standard subgroups to describe decompositions of Aut(G). If C is the commutation graph of G, we show how Aut(G) decomposes in terms of the connected components of C: obtaining a particularly clear decomposition theorem in the special case where C has no isolated vertices. If C has no vertices of a type we call dominated then we give a semi-direct decompostion of Aut(G) into a subgroup of locally conjugating automorphisms by the subgroup stabilising a certain lattice of "admissible subsets" of the vertices of C. We then characterise those graphs for which Aut(G) is a product (not necessarily semi-direct) of two such subgroups.Comment: 7 figures, 63 pages. Notation and definitions clarified and typos corrected. 2 new figures added. Appendix containing details of presentation and proof of a theorem adde

Large-area sheet task advanced dendritic web growth development

The thermal models used for analyzing dendritic web growth and calculating the thermal stress were reexamined to establish the validity limits imposed by the assumptions of the models. Also, the effects of thermal conduction through the gas phase were evaluated and found to be small. New growth designs, both static and dynamic, were generated using the modeling results. Residual stress effects in dendritic web were examined. In the laboratory, new techniques for the control of temperature distributions in three dimensions were developed. A new maximum undeformed web width of 5.8 cm was achieved. A 58% increase in growth velocity of 150 micrometers thickness was achieved with dynamic hardware. The area throughput goals for transient growth of 30 and 35 sq cm/min were exceeded