Operating characteristics of a hollow-cathode neutralizer for 5 and 8 centimeter-diameter electron bombardment mercury ion thrusters

Thin-tip 0.3-cm-outside-diameter hollow-cathode neutralizers were used to investigate causes of neutralizer tip erosion experienced in thruster endurance tests. Bell-jar tests indicated that neutralizers with new rolled tantalum foil inserts coated with an emissive mixture eroded very little over the neutral flow rates investigated (3 to 10 mA) for simulated 5- and 8-cm-diameter thruster neutralizer conditions. Tip erosion rates of neutralizers operated with no insert or emissive mixture increased by two orders of magnitude for both configurations as the neutral flow rate decreased. Spectroscopic analysis of the discharge plasma from neutralizers operated with inserts coated with the emissive mixture detected tungsten at all neutral flow rates for both thruster neutralizer conditions. The only source of tungsten was the tip. Therefore, detection of tungsten indicated neutralizer tip erosion. Barium, an element of the emissive mixture, was detected at low neutral flow rates for the 5-cm-diameter thruster neutralizer operating condition only

Texturing polymer surfaces by transfer casting

A technique for fabricating textured surfaces on polymers without altering their surface chemistries is described. A surface of a fluorocarbon polymer is exposed to a beam of ions to texture it. The polymer which is to be surface-roughened is then cast over the textured surface of the fluorocarbon polymer. After curing, the cast polymer is peeled off the textured fluorocarbon polymer, and the peeled off surface has negative replica of the textured surface. The microscopic surface texture provides large surface areas for adhesive bonding. In cardiovascular prosthesis applications the surfaces are relied on for the development of a thin adherent well nourished thrombus

Hollow cathodes with BaO impregnated, porous tungsten inserts and tips

The technology of impregnated materials is described and some inherently advantageous characteristics of impregnated cathodes are discussed. Thermionic emission measurements are presented for oxide coated and impregnated cathodes. Five cathode configurations with barium oxide impregnated porous tungsten inserts and/or tips have been fabricated and tested. Reliability, durability, and stability of operation are characterized. One of the cathodes has accumulated over 9000 operational hours, another has been cycled on and off more than 800 times

Scanning-electron-microscopy observations and mechanical characteristics of ion-beam-sputtered surgical implant alloys

An electron bombardment ion thruster was used as an ion source to sputter the surfaces of orthopedic prosthetic metals. Scanning electron microscopy photomicrographs were made of each ion beam textured surface. The effect of ion texturing an implant surface on its bond to bone cement was investigated. A Co-Cr-W alloy and surgical stainless steel were used as representative hard tissue implant materials to determine effects of ion texturing on bulk mechanical properties. Work was done to determine the effect of substrate temperature on the development of an ion textured surface microstructure. Results indicate that the ultimate strength of the bulk materials is unchanged by ion texturing and that the microstructure will develop more rapidly if the substrate is heated prior to ion texturing

Development of a qualification standard for adhesives used in hybrid microcircuits

Improved qualification standards and test procedures for adhesives used in microelectronic packaging are developed. The test methods in specification for the Selection and Use of Organic Adhesives in Hybrid Microcircuits are reevaluated versus industry and government requirements. Four electrically insulative and four electrically conductive adhesives used in the assembly of hybrid microcircuits are selected to evaluate the proposed revised test methods. An estimate of the cost to perform qualification testing of an adhesive to the requirements of the revised specification is also prepared

The inheritance of dynamic and deontic integrity constraints or: Does the boss have more rights?

In [18,23], we presented a language for the specification of static, dynamic and deontic integrity constraints (IC's) for conceptual models (CM's). An important problem not discussed in that paper is how IC's are inherited in a taxonomic network of types. For example, if students are permitted to perform certain actions under certain preconditions, must we repeat these preconditions when specializing this action for the subtype of graduate students, or are they inherited, and if so, how? For static constraints, this problem is relatively trivial, but for dynamic and deontic constraints, it will turn out that it contains numerous pitfalls, caused by the fact that common sense supplies presuppositions about the structure of IC inheritance that are not warranted by logic. In this paper, we unravel some of these presuppositions and show how to avoid the pitfalls. We first formulate a number of general theorems about the inheritance of necessary and/or sufficient conditions and show that for upward inheritance, a closure assumption is needed. We apply this to dynamic and deontic IC's, where conditions arepreconditions of actions, and show that our common sense is sometimes mistaken about the logical implications of what we have specified. We also show the connection of necessary and sufficient preconditions of actions with the specification of weakest preconditions in programming logic. Finally, we argue that information analysts usually assume constraint completion in the specification of (pre)conditions analogous to predicate completion in Prolog and circumscription in non-monotonic logic. The results are illustrated with numerous examples and compared with other approaches in the literature

Direct thrust measurement of a 30-cm ion thruster

A direct thrust measurement of a 30-cm diameter ion thruster was accomplished by means of a laser interferometer thrust stand. The thruster was supported in a pendulum manner by three 3.65-m long wires. Electrical power was provided by means of 18 mercury filled pots. A movable 23-button planar probe rake was used to determine thrust loss due to ion beam divergence. Values of thrust, thrust loss due to ion beam divergence, and thrust loss due to multiple ionization were measured for ion beam currents ranging from 0.5 A to 2.5 A. Measured thrust values indicate an accuracy of approximately 1% and are in good agreement with thrust values calculated by indirect measurements

Optical properties of ion beam textured metals

Copper, silicon, aluminum, titanium and 316 stainless steel were textured by 1000 eV xenon ions from an 8 cm diameter electron bombardment ion source. Simultaneously sputter-deposited tantalum was used to facilitate the development of the surface microstructure. Scanning electron microscopy of the ion textured surfaces revealed two types of microstructure. Copper, silicon, and aluminum developed a cone structure with an average peak-to-peak distance ranging from 1 micron for silicon to 6 microns for aluminum. Titanium and 316 stainless steel developed a serpentine ridge structure. The average peak-to-peak distance for both of these materials was 0.5 micron. Spectral reflectance was measured using an integrating sphere and a holraum reflectometer. Total reflectance for air mass 0 and 2, solar absorptance and total emittance normalized for a 425 K black body were calculated from the reflectance measurements

Cascaded Nondegenerate Four-Wave Mixing Technique for High-Power Single-Cycle Pulse Synthesis in the Visible and Ultraviolet Ranges

We present a new technique to synthesize high-power single-cycle pulses in the visible and ultraviolet ranges by coherent superposition of a multiband octave-spanning spectrum obtained by highly-nondegenerate cascaded four-wave mixing of femtosecond pulses in bulk isotropic nonresonant media. The generation of coherent spectra spanning over two octaves in bandwidth is experimentally demonstrated using a thin fused silica slide. Full characterization of the intervening multicolored fields using frequency-resolved optical gating, where multiple cascaded orders have been measured simultaneously for the first time, supports the possibility of direct synthesis of near-single-cycle 2.2 fs visible-UV pulses without recurring to complex amplitude or phase control, which should enable many applications in science and technology.Comment: 13 pages, 4 figures. Submitted to Physical Review