664 research outputs found

    Low‐temperature frictional characteristics of chlorite‐epidote‐amphibole assemblages: implications for strength and seismic style of retrograde fault zones

    Get PDF
    In retrograde faults exhuming mafic rocks, shearing occurs in metamorphic and/or hydrothermally altered mineral assemblages whose frictional properties are not well known. Here, we present the results of laboratory shearing experiments on chlorite schist, epidotite, and hornblende‐dominated amphibolite and mixtures of these rocks and evaluate their frictional properties and microstructures. The experiments were conducted on powdered rock samples with starting grain size of <125 ÎŒm, at room temperature, under fluid‐saturated conditions and applied normal stress of 10 MPa. The results show that chlorite schist is relatively weak (friction coefficient of 0.36), whereas epidotite and amphibolite are strong (friction coefficients of 0.63 and 0.67, respectively). The friction of chlorite schist‐epidotite and chlorite schist‐amphibolite mixtures decreases nearly linearly with increasing chlorite content. Chlorite schist exhibits velocity‐strengthening behavior, epidotite is velocity‐weakening, and the amphibolite shows mostly velocity‐weakening friction. Mixtures show intermediate strength and velocity dependence of friction. Well‐developed striations formed on slip surfaces in samples with ≄50% chlorite schist. The epidotite slip surface exhibits a mixture of very fine particles and coarser crystals. Amphibolite slip surfaces have less very fine grains and are composed of subhedral to euheral needles. Few intragranular fractures are preserved, and we infer wear at contact asperities to be the likely cause of velocity‐weakening in our epidote gouges. Addition of chlorite to epidotite and amphibolite produces a striated slip surface and disrupts contacts between harder grains. Therefore, retrograde chlorite growth is expected to facilitate frictional weakening and stable slip in higher‐grade mineral assemblages exhumed to low‐temperature conditions

    Shear behavior of DFDP-1 borehole samples from the Alpine Fault, New Zealand, under a wide range of experimental conditions

    Get PDF
    The Alpine Fault is a major plate-boundary fault zone that poses a major seismic hazard in southern New Zealand. The initial stage of the Deep Fault Drilling Project has provided sample material from the major lithological constituents of the Alpine Fault from two pilot boreholes. We use laboratory shearing experiments to show that the friction coefficient ” of fault-related rocks and their precursors varies between 0.38 and 0.80 depending on the lithology, presence of pore fluid, effective normal stress, and temperature. Under conditions appropriate for several kilometers depth on the Alpine Fault (100 MPa, 160 °C, fluid-saturated), a gouge sample located very near to the principal slip zone exhibits ” = 0.67, which is high compared with other major fault zones targeted by scientific drilling, and suggests the capacity for large shear stresses at depth. A consistent observation is that every major lithological unit tested exhibits positive and negative values of friction velocity dependence. Critical nucleation patch lengths estimated using representative values of the friction velocity-dependent parameter a−b and the critical slip distance D c , combined with previously documented elastic properties of the wall rock, may be as low as ~3 m. This small value, consistent with a seismic moment M o = ~4 × 1010 for an M w = ~1 earthquake, suggests that events of this size or larger are expected to occur as ordinary earthquakes and that slow or transient slip events are unlikely in the approximate depth range of 3–7 km

    Frictional strengthening explored during non-steady state shearing. Implications for fault stability and slip event recurrence time

    Get PDF
    On natural faults that host repeating slip events, the inter-event loading time is quite large compared to the slip event duration. Since most friction studies focus on steady-state frictional behavior, the fault loading phase is not typically examined. Here, we employ a method specifically designed to evaluate fault strength evolution during active loading, under shear driving rates as low as 10−10&nbsp;m/s, on natural fault gouge samples from the Waikukupa Thrust in southern New Zealand. These tests reveal that in the early stages of loading following a slip event, there is a period of increased stability, which fades with accumulated slip. In the framework of rate- and state-dependent friction laws, this temporary stable phase exists as long as slip is less than the critical slip distance and the elapsed time is less than the value of the state variable at steady state. These observations indicate a minimum earthquake recurrence time, which depends on the field value of the critical slip distance and the background slip rate. We compare estimates of minimum earthquake recurrence times with the recurrence times of repeating large earthquakes on the Alpine Fault in southern New Zealand and repeating small-magnitude earthquakes on the San Andreas Fault system in California. We find that the observed recurrence times are mostly longer than the predicted minimum values, and exceptions in the San Andreas system may be explained by elevated slip rates due to larger earthquakes in this region

    Frictional and lithological controls on shallow slow slip at the Northern Hikurangi Margin

    Get PDF
    Slow slip events (SSEs) have been identified at subduction zones globally as an important link in the continuum between elastodynamic ruptures and stable creep. The northern Hikurangi margin is home to shallow SSEs which propagate to within 2&nbsp;km of the seafloor and possibly to the trench, providing insights into the physical conditions conducive to SSE behavior. We report on a suite of friction experiments performed on protolith material entering the SSE source region at the Hikurangi margin, collected during the International Ocean Discovery Program Expedition 375. We performed velocity stepping and slide-hold-slide experiments over a range of fault slip rates, from plate rate (5&nbsp;cm/yr or 1.6&nbsp;×&nbsp;10−9&nbsp;m/s) to ∌1&nbsp;mm/s (10−3&nbsp;m/s) and quantified the frictional velocity dependence and healing rates for a range of lithologies atdifferent stresses. The frictional velocity dependence (a-b) and critical slip distance DC increase with fault slip rate in our experiments. We observe atransition from velocity weakening to strengthening at slip rates of ∌0.3 ”m/s. This velocity dependence of DC could be due to a combination of dilatant strengthening and a widening of the active shear zone at higher slip rates. We document low healing rates in the clay-rich volcaniclastic conglomerates, which lie above the incoming plate basement at least locally, and relatively higher healing rates in the chalk lithology. Finally, our experimental constraints on healing rates in different input lithologies extrapolated to timescales of 1–10&nbsp;years are consistent with the geodetically inferred low stress drops and healing rates characteristic of the Hikurangi SSEs

    Mixed brittle and viscous strain localisation in pelagic sediments seaward of the Hikurangi margin, New Zealand

    Get PDF
    Calcareous‐pelagic input sediments are present at several subduction zones and deform differently to their siliciclastic counterparts. We investigate deformation in calcareous‐pelagic sediments drilled ~20 km seaward of the Hikurangi megathrust toe at Site U1520 during IODP Expeditions 372 and 375. Clusters of normal faults and subhorizontal stylolites in the sediments indicate both brittle faulting and viscous pressure solution operated at 150°C where frictional (possibly seismic) slip likely predominates. Plain Language Summary The type of sediments entering subduction zones will influence the way the plates in the subduction zone slide past one another. We looked at limestones in sediments drilled before they reach the subduction zone and found that because of the pressure they are under, they begin to crack and dissolve at very shallow depths. Most of the dissolution happens on thin layers where it concentrates clay by removing other, more soluble minerals. We compare how much vertical shortening we see in the sediments to a computer model. The model overestimates vertical shortening over the history of the sediment unless either high pressure fluids reduce the pressure felt by the sediments, or dissolution is governed by the largest sediment grains rather than their average size. Dissolving and cracking make the sediments weaker by concentrating soft materials such as clay. When these sediments enter the subduction zone, the two plates might slip past one another more easily on these weak regions, possibly during slow slip events

    Application of constitutive friction laws to glacier seismicity

    Get PDF
    While analysis of glacial seismicity continues to be a widely used method for interpreting glacial processes, the underlying mechanics controlling glacial stick-slip seismicity remain speculative. Here, we report on laboratory shear experiments of debris-laden ice slid over a bedrock asperity under carefully controlled conditions. By modifying the elastic loading stiffness, we generated the first laboratory icequakes. Our work represents the first comprehensive lab observations of unstable ice-slip events and replicates several seismological field observations of glacier slip, such as slip velocity, stress drop, and the relationship between stress drop and recurrence interval. We also observe that stick-slips initiate above a critical driving velocity and that stress drop magnitude decreases with further increases in velocity, consistent with friction theory and rock-on-rock friction laboratory experiments. Our results demonstrate that glacier slip behavior can be accurately predicted by the constitutive rate-and-state friction laws that were developed for rock friction

    Frictional characteristics of oceanic transform faults: progressive deformation and alteration controls seismic style

    Get PDF
    Oceanic transform faults are inferred to be weak relative to surrounding oceanic crust and primarily slip aseismically. Neither their weakness nor tendency to creep are well-explained. We test the effects of fault-rock evolution on oceanic transform fault frictional strength and stability using direct-shear experiments (at room temperature, 10 MPa normal stress, and fluid-saturated conditions) on dolerite from the East Pacific Rise and natural fault rocks from the exhumed Southern Troodos Transform, Cyprus. Dolerites and cemented breccias are frictionally strong (ÎŒ = 0.52–0.85) and velocity-weakening (strength decreases with increasing slip velocity, characteristic of earthquakes). In contrast, matrix-rich chlorite-bearing fault breccias and gouges are frictionally weak (ÎŒ = 0.25–0.48) and velocity-strengthening (characteristic of stable creep). This transition implies that seismic behavior is controlled by degree of damage and alteration, such that earthquakes can nucleate within relatively intact oceanic crust, whereas fault segments of increased damage and chlorite content tend to slip aseismically

    Mixed brittle and viscous strain localisation in pelagic sediments seaward of the Hikurangi margin, New Zealand

    Get PDF
    Calcareous‐pelagic input sediments are present at several subduction zones and deform differently to their siliciclastic counterparts. We investigate deformation in calcareous‐pelagic sediments drilled ~20 km seaward of the Hikurangi megathrust toe at Site U1520 during IODP Expeditions 372 and 375. Clusters of normal faults and subhorizontal stylolites in the sediments indicate both brittle faulting and viscous pressure solution operated at 150°C where frictional (possibly seismic) slip likely predominates

    Frictional Behavior of Input Sediments to the Hikurangi Trench, New Zealand

    Get PDF
    AbstractThe Hikurangi subduction zone hosts shallow slow‐slip events, possibly extending to the seafloor. The mechanisms allowing for this behavior are poorly understood but are likely a function of the frictional properties of the downgoing seafloor sediments. We conducted friction experiments at a large range of effective stresses, temperatures, and velocities on incoming sediment to the Hikurangi subduction zone to explore the possible connection of frictional properties to slow‐slip events. These experiments were conducted on multiple apparatuses, allowing us to access a wider range of deformation conditions than is available on any one machine. We find that the material frictionally weakens and becomes less velocity strengthening with increasing effective stress, whereas temperature has only a small effect on both friction and frictional stability. When driven at the plate convergence rate, the sediment exhibits velocity‐weakening behavior. These results imply that the frictional properties of the sediment package subducting at Hikurangi could promote slow‐slip events at the pressures, temperatures, and strain rates expected along the plate boundary thrust up to 10‐km depth without requiring elevated pore fluid pressures. The transition to velocity‐strengthening behavior at faster slip rates could provide a mechanism for limiting unstable slip to slow‐sliding velocities, rather than accommodating deformation through ordinary earthquakes
    • 

    corecore