738 research outputs found
Atomic force microscopy shows that vaccinia topoisomerase IB generates filaments on DNA in a cooperative fashion
Type IB DNA topoisomerases cleave and rejoin one strand of the DNA duplex, allowing for the removal of supercoils generated during replication and transcription. In addition, electron microscopy of cellular and viral TopIBāDNA complexes has suggested that the enzyme promotes long-range DNAāDNA crossovers and synapses. Here, we have used the atomic force microscope to visualize and quantify the interaction between vaccinia topoisomerase IB (vTopIB) and DNA. vTopIB was found to form filaments on nicked-circular DNA by intramolecular synapsis of two segments of a single DNA molecule. Measuring the filament length as a function of protein concentration showed that synapsis is a highly cooperative process. At high protein:DNA ratios, synapses between distinct DNA molecules were observed, which led to the formation of large vTopIB-induced DNA clusters. These clusters were observed in the presence of Mg(2+), Ca(2+) or Mn(2+), suggesting that the formation of intermolecular vTopIB-mediated DNA synapsis is favored by screening of the DNA charge
Montmorilonit ā usporedba metoda za njegovo odreÄivanje u ljevaoniÄkim bentonitima
A comparison and estimation of usefulness of a quantitative analysis of montmorillonite in foundry bentonites, was the aim of this research. The investigations were made by means of three different techniques: methylene blue (MB) adsorption method, Cu(II)-triethylenetetramine complex (Cu(II)-TET) adsorption method, and infrared spectroscopy (FTIR) method. Tests were performed for 9 kinds of bentonites originated from various producers. The achieved results indicated that, the results obtained by the FTIR method were, in general, even 10% lower than the ones obtained by other methods. The best correlation with the data given by the producers were obtained for the Cu(II)-TET method. In addition, this method was characterised by the smallest value of standard deviations. A very essential advantage of the Cu(II)-TET method is a much shorter time needed for the analysis and its easier execution, which is important under production conditions.Cilj ovog istraživanja je bila procjena upotrebljivosti kvantitativne analize montmorilonita u ljevaoniÄkim bentonitima. Istraživanja su provedena pomoÄu tri razliÄite tehnike: adsorpcija metilenskog modrila (MB), adsorpcija Cu(II)-trietilentetramin kompleksa (CU(II)-TET), i infracrvena spektroskopija (FTIR). Ispitivanja su provedena na 9 vrsta bentonita koji potjeÄu od razliÄitih proizvoÄaÄa. Rezultati dobiveni FTIR metodom u prosjeku su za Äak 10,0% niži od rezultata dobivenih ostalim metodama. Najbolja korelacija s podatcima od proizvoÄaÄa dobivena je primjenom Cu(II)-TET metode. Osim toga, kod te metode najmanje su vrijednosti standardnih devijacija. Vrlo važna prednost Cu(II)-TET metode je znatno kraÄe vrijeme potrebno za anaalizu i lakÅ”e provoÄenje, Å”to je znaÄajno u proizvodnim uvjetima
Observation via one-dimensional 13Calpha NMR of local conformational substates in thermal unfolding equilibria of a synthetic analog of the GCN4 leucine zipper.
Investigations of Protective Coatings for Castings of High-manganese Cast Steels
When cast steel castings are made in moulding sands on matrices of high-silica sand, which has a low fire resistance the problem of theso-called chemical penetration is distinctly visible. Whereas this effect appears to a small degree only when moulding sand matrices are of chromite, zircon or olivine sands. Therefore in case of making castings of high-manganese cast steel (e.g. Hadfield steel) sands not containing free silica should be applied (e.g. olivine sand) or in case of a high-silica matrix protective coatings for moulds and cores should be used. Two protective coatings, magnesite alcoholic (marked as coating 1 and coating 2) originated from different producers and intended for moulds for castings of the Hadfield steel, were selected for investigations. Examinations of the basic properties were performed for these coatings: viscosity, thermal analysis, sedimentation properties, wear resistance. In order to estimate the effectiveness of protective coatings the experimental castings were prepared. When applying coating 1, the surface quality of the casting was worse and traces of interaction between the casting material (cast steel) and the coating were seen. When protective coating 2 was used none interactions were seen and the surface quality was better
Thermal decomposition of foundry resins: A determination of organic products by thermogravimetryāgas chromatographyāmass spectrometry (TGāGCāMS)
AbstractThe article presents the results of research on thermal decomposition of Ester-Cured Alkaline Phenolic No-Bake (ALPHASET) binders used in molding technology. In the ALPHASET system phenol-formaldehyde resin of resole type is cured with a liquid mixture of esters. Under the influence of the molten metal the thermal decomposition of the binder follows, resulting in the evolution of gases, often harmful, e.g. from benzene, toluene, ethylbenzene and xylenes (BTEX) or Polycyclic Aromatic Hydrocarbon (PAH) groups. The identification of gases evolved during the pyrolysis of the binders was carried out and their decomposition temperatures were determined using the ThermogravimetryāGas ChromatographyāMass Spectrometry (TGāGCāMS) technique. The tests were subjected to two types of binders from different manufacturers. Among the products of pyrolysis there have been identified mainly benzene and its derivatives, and phenol and its derivatives. Compounds identified in pyrolytic gas are largely considered to be harmful to humans and the environment (some of the compounds are carcinogenic and mutagenic). The presented results of the TGāGCāMS measurements show that the applied analytic methods are feasible to perform a qualitative and also quantitative characterization of the binder samples
- ā¦