Rapid and Accurate Determination of Stern-Volmer Quenching Constants

In this work, a novel system has been designed, characterized, and validated for the determination of fluorescence quenching constants. Capillary flow injection methods are used to automate the preparation and mixing of the fluorophore and quencher solutions. Because of the small diameter of the capillary (75-200 mu m), fluorescence measurements can be made without corrections for primary and secondary absorbance effects. The fluorescence spectrometer is equipped with a charge-coupled device (CCD) that has a detection limit of 3.0 X 10-9 M (2.3 ppb) and a linear dynamic range of 10 5 for integration times of 0.01-10 s. This spectrometer has a 300 nm spectral range with 1 nm resolution, allowing the fluorescence quenching constants to be calculated at single wavelengths or over integrated wavelength ranges. This system was validated by comparison to traditional methods for the determination of Stern-Volmer constants for alternant and nonalternant polycyclic aromatic hydrocarbons with nitromethane and triethylamine

Preparation and characterization of micro-bore wall-coated open-tubular capillaries with low phase ratios for fast-gas chromatography–mass spectrometry: Application to ignitable liquids and fire debris

Fast Gas Chromatography (GC) allows for analysis times that are a fraction of those seen in traditional capillary GC. Key modifications in fast GC include using narrow, highly efficient columns that can resolve mixtures using a shorter column length. Hence, a typical fast GC column has an inner diameter of 100–180 μm. However, to maintain phase ratios that are consistent with typical GC columns, the film thickness of fast GC stationary phases are also low (e.g., 0.1–0.18 μm). Unfortunately, decreased film thickness leads to columns with very low sample capacity and asymmetric peaks for analytes that are not sufficiently dilute. This paper describes micro-bore (50 μm i.d.) capillary columns with thick films (1.25 μm), and low phase ratios (10). These columns have greater sample capacity yet also achieve minimum plate heights as low as 110 μm. Hence, separation efficiency is much higher than would be obtained using standard GC columns. The capillary columns were prepared in-house using a simple static-coating procedure and their plate counts were determined under isothermal conditions. The columns were then evaluated using temperature programming for fast GC–MS analysis of ignitable liquids and their residues on fire debris exemplars. Temperature ramps of up to 75 °C min−1 could be used and separations of ignitable liquids such as gasoline, E85 fuel, and lighter fluid (a medium petroleum distillate) were complete within 3 min. Lastly, simulated fire debris consisting of ignitable liquids burned on carpeting were extracted using passive headspace absorption-elution and the residues successfully classified

Generating Highly Specific Spectra and Identifying Thermal Decomposition Products via Gas Chromatography / Vacuum Ultraviolet Spectroscopy (GC/VUV): Application to Nitrate Ester Explosives

Gas chromatography/mass spectrometry (GC/MS) is a "workhorse" instrument for chemical analysis, but it can be limited in its ability to differentiate structurally similar compounds. The coupling of GC to vacuum ultraviolet (VUV) spectroscopy is a recently developed technique with the potential for increased detection specificity. To date, GC/VUV has been demonstrated in the analysis of volatile organic compounds, petroleum products, aroma compounds, pharmaceuticals, illegal drugs, and lipids. This paper is the first to report on the utility of GC/VUV for explosives analysis in general, and the first to report on thermal degradation within the VUV cell and its analytical utility. The general figures of merit and performance of GC/VUV were evaluated with authentic standards of nitrate ester explosives (e.g., nitroglycerine (NG), ethylene glycol dinitrate (EGDN), pentaerythritol tetranitrate (PETN), and erythritol tetranitrate (ETN)). In addition, the explosive analytes were thermally degraded in the VUV cell, yielding reproducible, complex and characteristic mixtures of gas phase products (e.g., nitric oxide, carbon monoxide, and formaldehyde). The relative amounts of the degradation products were estimated via spectral subtraction of library spectra. Lastly, GC/VUV was used to analyze milligram quantities of intact and burned samples of double-base smokeless powders containing nitroglycerine, diphenylamine, ethyl centralite, and dibutylphthalat

Fabrication of a Self-Assembled and Flexible SERS Nanosensor for Explosive Detection at Parts-Per-Quadrillion Levels from Fingerprints

Apart from high sensitivity and selectivity of surface-enhanced Raman scattering (SERS)-based trace explosive detection, efficient sampling of explosive residue from real world surfaces is very important for homeland security applications. Herein, we demonstrate an entirely new SERS nanosensor fabrication approach. The SERS nanosensor was prepared by self-assembling chemically synthesized gold triangular nanoprisms (Au TNPs), which we show display strong electromagnetic field enhancements at the sharp tips and edges, onto a pressure-sensitive flexible adhesive film. Our SERS nanosensor provides excellent SERS activity (enhancement factor = ∼6.0 × 106) and limit of detection (as low as 56 parts-per-quadrillions) with high selectivity by chemometric analyses among three commonly military high explosives (TNT, RDX, and PETN). Furthermore, the SERS nanosensors present excellent reproducibility (<4.0% relative standard deviation at 1.0 μM concentration) and unprecedentedly high stability with a “shelf life” of at least 5 months. Finally, TNT and PETN were analyzed and quantified by transferring solid explosive residues from fingerprints left on solid surfaces to the SERS nanosensor. Taken together, the demonstrated sensitivity, selectivity, and reliability of the measurements as well as with the excellent shelf life of our SERS nanosensors obviate the need for complicated sample processing steps required for other analytical techniques, and thus these nanosensors have tremendous potential not only in the field of measurement science but also for homeland security applications to combat acts of terror and military threats

Solvent Azeotropes in Art Conservation

Solvent mixtures are often fine-tuned by art conservators for the difficult tasks of safely removing yellowed varnishes and obfuscating dirt from oil paintings. These two goals are often loosely termed “picture cleaning.” Concern has been raised over the impact of differential evaporation rates for solvents in the cleaning mixture. Differential evaporation can lead to changes in the mixture’s potency over time and potentially lead to solvent mixtures on the surface of the artwork having solubility characteristics deleterious to artists’ oil paints. Azeotropic mixtures of solvents have been proposed as an alternative for maintaining consistent solvent composition. Azeotropes are specific mixtures of two or more solvents that behave as a single solvent and maintain a constant composition at their boiling point. The azeotropes that have appeared in the art conservation literature are taken from tables of azeotropic compositions in the CRC Handbook given at their boiling point. This research examines whether these solvent blends, in particular a hexane/isopropanol combination found to be an effective cleaner in the treatment of painted royal sleighs at the Palace of Versailles, in fact behave azeotropically under room temperature evaporation conditions. For the first time, the actual evaporation behavior of this purported azeotropic mixture will be explored in depth. A range of hexane/isopropanol mixtures around the boiling point azeotrope composition have been assessed for their room temperature vapor pressure and evaporation weight loss kinetics. Aliquots of the evaporating solutions are also being analyzed chemically using gas chromatography of both the liquid phase and the vapor phase in the headspace. This research aims to provide conservators information on the evaporation of purportedly azeotropic solvent blends and to suggest new approaches to the cleaning of oil paintings

Quantitative Analysis of Humectants in Tobacco Products Using Gas Chromatography (GC) with Simultaneous Mass Spectrometry (MSD) and Flame Ionization Detection (FID)

This paper describes the modification of an existing gas chromatographic (GC) method to incorporate simultaneous mass spectrometric (MSD) and flame ionization detection (FID) into the analysis of tobacco humectants. Glycerol, propylene glycol, and triethylene glycol were analyzed in tobacco labeled as roll-your-own (RYO), cigar, cigarette, moist snuff, and hookah tobacco. Tobacco was extracted in methanol containing 1,3-butanediol (internal standard), filtered, and separated on a 15 m megabore DB-Wax column. Post-column flow was distributed using a microfluidic splitter between the MSD and FID for simultaneous detection. The limits of detection for the FID detector were 0.5 μg/mL (propylene glycol and triethylene glycol) and 0.25 μg/mL (glycerol) with a linear range of 2–2000 μg/mL (propylene glycol and triethylene glycol) and 1–4000 μg/mL (glycerol). The limits of detection for the MSD detector were 2 μg/mL (propylene glycol and triethylene glycol) and 4 μg/mL (glycerol) with a linear range of 20–2000 μg/mL (propylene glycol and triethylene glycol) and 40–4000 μg/mL (glycerol). Significant improvement in the sensitivity of the MSD can be achieved by employing selective ion monitoring (SIM) detection mode. Although a high degree of correlation was observed between the results from FID and MSD analyses, marginal chromatographic resolution between glycerol and triethylene glycol limits the applicability of FID to samples containing low levels of both of these humectants. Utilizing MSD greatly improves the reliability of quantitative results because compensation for inadequate chromatographic resolution can be accomplished with mass selectivity in detection

Microbial Degradation of Gasoline in Soil: Effect of Season of Sampling

In cases where fire debris contains soil, microorganisms can rapidly and irreversibly alter the chemical composition of any ignitable liquid residue that may be present. In this study, differences in microbial degradation due to the season in which the sample is collected was examined. Soil samples were collected from the same site during Fall, Winter, Spring and Summer and the degradation of gasoline was monitored over 30 days. Predominant viable bacterial populations enumerated using real-time PCR and reverse transcriptase polymerase chain reaction (RT-PCR) enumeration revealed the predominant viable bacterial genera to be Alcaligenes, Bacillus, and Flavobacterium. Overall, the compounds most vulnerable to microbial degradation are the n-alkanes, followed by the mono-substituted alkylbenzenes (e.g., toluene, ethylbenzene, propylbenzene and isopropylbenzene). Benzaldehyde (a degradation product of toluene) was also identified as a marker for the extent of biodegradation. Ultimately, it was determined that soil collected during an unusually hot and dry summer exhibited the least degradation with little to no change in gasoline for up to 4 days, readily detectable n-alkanes for up to 7 days and relatively high levels of resilient compounds such as o-xylene, p-xylene and 1,3,5-trimethylbenzene. These results demonstrate, however, that prompt preservation and/or analysis of soil evidence is required in order to properly classify an ignitable liquid residue

A Comprehensive Study of the Alteration of Ignitable Liquids by Weathering and Microbial Degradation

The differing effects of weathering and microbial degradation are described here in a comprehensive study that involved 50 different ignitable liquids from the Ignitable Liquids Database and Reference Collection. Examples of ignitable liquid residues from each of the main classes established by the American Society of Testing and Materials are presented. Weathering was accomplished via evaporation, whereas microbial degradation was carried out on soil at room temperature for periods of up to 21 days. Major trends included the rapid degradation of long n-alkanes and monosubstituted alkyl benzenes (e.g., toluene, ethylbenzene, and propylbenzene). Surprisingly, some longer branched alkanes (e.g., trimethyloctanes) were also susceptible to microbial attack. Although all ignitable liquids examined suffered at least to some extent from microbial degradation, gasoline, petroleum distillates, and oxygenates were the most susceptible. Isoparaffinic and naphthenic–paraffinic products were the most resistant to microbial degradation

Differentiation of Structurally Similar Phenethylamines via Gas Chromatography - Vacuum Ultraviolet Spectroscopy (GC – VUV)

The vacuum ultraviolet region includes wavelengths shorter than 200 nm. Electronic transitions of sigma and pi bonds lie in this region, which have the potential to yield structural information. Thus, a VUV detector should be able to detect nearly any molecule analyzable by gas chromatography. This study sought to determine the extent to which structurally similar phenethylamines are differentiated using their VUV spectra. Phenethylamines are a common drug class including pseudoephedrine and illicit drugs such as methamphetamine. Several phenethylamines are difficult to analyze by electron impact mass spectrometry due to their fragmentation giving the same mass to charge ratio fragments at similar ratios. While phenethylamines are generally differentiable by retention time, an extra layer of specificity is preferred in forensic analyses. A vacuum ultraviolet (VUV) spectrophotometer coupled to a gas chromatograph was used to collect VUV spectra at high frequency between 125 and 430 nm. Eight phenethylamines were analyzed for this work using GC/VUV. A calibration curve and limit of detection study was performed that indicates a limit of detection around 10 μg mL−1 and an upper limit of linearity around 1000 μg mL−1. The spectra, analyzed by Principal Component Analysis and Discriminant Analysis, indicate the ability to reliably differentiate each of the drugs from one another including structural isomers and diastereomers. Lastly, five “street” samples containing amphetamines were analyzed to demonstrate “real world” performance

Characterization of Automotive Paint Clear Coats by Ultraviolet Absorption Microspectrophotometry with Subsequent Chemometric Analysis

Clear coats have been a staple in automobile paints for almost thirty years and are of forensic interest when comparing transferred and native paints. However, the ultraviolet (UV) absorbers in these paint layers are not typically characterized using UV microspectrophotometry, nor are the results studied using multivariate statistical methods. In this study, measurements were carried out by UV microspectrophotometry on 71 samples from American and Australian automobiles, with subsequent chemometric analysis of the absorbance spectra. Sample preparation proved to be vital in obtaining accurate absorbance spectra and a method involving peeling the clear coat layer and not using a mounting medium was preferred. Agglomerative hierarchical clustering indicated three main groups of spectra, corresponding to spectra with one, two, and three maxima. Principal components analysis confirmed this clustering and the factor loadings indicated that a substantial proportion of the variance in the data set originated from specific spectral regions (230–265 nm, 275–285 nm, and 300–370 nm). The three classes were well differentiated using discriminant analysis, where the cross-validation accuracy was 91.6% and the external validation accuracy was 81.1%. However, results showed no correlation between the make, model, and year of the automobiles