New Trends in Designing Parabolic trough Solar Concentrators and Heat Storage Concrete Systems in Solar Power Plants

Energy availability has always been an essential component of human civilization and the energetic consumption is directly linked to the produced wealth. In many depressed countries the level of solar radiation is considerably high and it could be the primary energy source under conditions that low cost, simple-to-be-used technologies are employed. Then, it is responsibility of the most advanced countries to develop new equipments to allow this progress for taking place. A large part of the energetic forecast, based on economic projection for the next decades, ensure us that fossil fuel supplies will be largely enough to cover the demand. The predicted and consistent increase in the energetic demand will be more and more covered by a larger use of fossil fuels, without great technology innovations. A series of worrying consequences are involved in the above scenario: important climatic changes are linked to strong CO2 emissions; sustainable development is hindered by some problems linked to certainty of oil and natural gas supply; problems of global poverty are not solved but amplified by the unavoidable increase in fossil fuel prices caused by an increase in demand. These negative aspects can be avoided only if a really innovative and more acceptable technology will be available in the next decades at a suitable level to impress a substantial effect on the society. Solar energy is the ideal candidate to break this vicious circle between economic progress and consequent greenhouse effect. The low penetration on the market shown today by the existent renewable technologies, solar energy included, is explained by well-known reasons: the still high costs of the produced energy and the \u201cdiscontinuity\u201d of both solar and wind energies. These limitations must be removed in reasonable short times, with the support of innovative technologies, in view of such an urgent scenario. On this purpose ENEA, on the basis of the Italian law n. 388/2000, has started an R&D program addressed to the development of CSP (Concentrated Solar Power) systems able to take advantage of solar energy as heat source at high temperature. One of the most relevant objectives of this research program (Rubbia, 2001) is the study of CSP systems operating in the field of medium temperatures (about 550\ub0C), directed towards the development of a new and low-cost technology to concentrate the direct radiation and efficiently convert solar energy into high temperature heat; another aspect is focused on the production of hydrogen by means of thermo-chemical processes at temperatures above 800\ub0C. As well as cost reductions, the current innovative ENEA conception aims to introduce a set of innovations, concerning: i) The parabolic-trough solar collector: an innovative design to reduce production costs, installation and maintenance and to improve thermal efficiency is defined in collaboration with some Italian industries; ii) The heat transfer fluid: the synthetic hydrocarbon oil, which is flammable, expensive and unusable beyond 400\ub0C, is substituted by a mixture of molten salts (sodium and potassium nitrate), widely used in the industrial field and chemically stable up to 600\ub0C; iii) The thermal storage (TES): it allows for the storage of solar energy, which is then used when energy is not directly available from the sun (night and covered sky) (Pilkington, 2000). After some years of R&D activities, ENEA has built an experimental facility (defined within the Italian context as PCS, \u201cProva Collettori Solari\u201d) at the Research Centre of Casaccia in Rome (ENEA, 2003), which incorporates the main proposed innovative elements. The next step is to test these innovations at full scale by means of a demonstration plant, as envisioned by the \u201cArchimede\u201d ENEA/ENEL Project in Sicily. Such a project is designed to upgrade the ENEL thermo-electrical combined-cycle power plant by about 5 MW, using solar thermal energy from concentrating parabolic-trough collectors. Particularly, the Chapter will focus on points i) and iii) above: - loads, actions, and more generally, the whole design procedure for steel components of parabolic-trough solar concentrators will be considered in agreement with the Limit State method, as well as a new approach will be critically and carefully proposed to use this method in designing and testing \u201cspecial structures\u201d such as the one considered here; - concrete tanks durability under prolonged thermal loads and temperature variations will be estimated by means of an upgraded F.E. coupled model for heat and mass transport (plus mechanical balance). The presence of a surrounding soil volume will be additionally accounted for to evaluate environmental risk scenarios. Specific technological innovations will be considered, such as: -higher structural safety related to the reduced settlements coming from the chosen shape of the tank (a below-grade cone shape storage); - employment of HPC containment structures and foundations characterized by lower costs with respect to stainless steel structures; - substitution of highly expensive corrugated steel liners with plane liners taking advantage of the geometric compensation of thermal dilations due to the conical shape of the tank; - possibility of employing freezing passive systems for the concrete basement made of HPC, able to sustain temperature levels higher than those for OPC; - fewer problems when the tank is located on low-strength soils

Conceptual Study of a Thermal Storage Module for Solar Power Plants with Parabolic Trough Concentrators

The thermal storage technology (TSE) has a relevant strategic importance for the success of solar plants devoted to electric energy and heat production. The major benefits in the use of storage include higher efficiency and reduction in the mean levelled cost of the electric energy unit (LEC). Sensible heat storage systems within solid media have been identified, both technically and economically, as a very promising solution. The development of such a storage technology, adopting concrete, could reduce the specific cost to less than 20\u20ac per kWh of thermal capacity; additionally, such a solution is suitable for small-medium size plants with a power ranging from 1 MW to 5 MW, to be easily introduced in the Italian territory and with reduced operational and maintenance needs. In large size CSP systems, as the ARCHIMEDE plant built by ENEL with ENEA technology, a high temperature fluid storage (between 400 and 500\ub0C) is required. Such a temperature seems at present not adequate to allow for adopting concrete, whereas the production of concrete able to sustain 250-300\ub0C appears as a reachable objective. It is supposed to study a storage system characterised by a parallelepiped structure with appropriate section, selfbearing and supported on its major axis, as well as by a piping system directing the thermovector fluid within the cemented matrix

High colouring efficiency, optical density and inserted charge in sol–gel derived electrochromic titania nanostructures

A pure TiO2 thin film (100–120 nm) was made from a green aqueous sol–gel precursor on FTO glass and calcined at 430 °C. It was a mix of amorphous, anatase, rutile and brookite TiO2 phases, and exhibited very good electrochromic properties over visible and NIR wavelengths with an applied bias of +0.1 V to −1.5 V. It was highly transparent showing excellent coloration with applied voltage, with transmittance modulation (ΔT) = 69.7% at 550 nm, 86% at 700 nm and an overall ΔT between 400–1650 nm of 60%, giving a very large change in optical density (ΔOD) of 1.4 at 550 nm and 2.4 at 700 nm. Cyclic voltammograms had typical peaks for TiO2 at −1.3 V for colouration and −0.9 V for bleaching, with a high separation of 0.37 V between peaks, and a charge density after charging for 25 min of Qc = 50 mC cm−2. After only 60 s and 120 s at −1.5 V, inserted charge values of 17.6 and 22 mC cm−2 were observed, leading to a high colouration efficiency (CE) of 55.9 cm2 C−1 at 550 nm. These ΔOD, ΔT, Qc and CE values are superior to any previously reported for crystalline sol–gel TiO2 films. They also possessed rapid switching times for bleaching and colouring of τb90% = 10 s and τc90% = 55 s, comparable to the best previously reported sol–gel anatase-based TiO2 films. This makes this nanomaterial an excellent candidate for smart windows and other electrochromic devices and applications

Sicilia-Malta: il nuovo collegamento RTN a 220 kV in corrente alternata

Descrizione dettagliata degli aspetti tecnologici e delle prestazioni funzionali di maggiore rilevanza sui cavi utilizzati, sui sistemi e sulle logiche di protezione contro i guasti. Vantaggi, potenzialità e criticità legate all’esercizio

Experimental campaign and numerical analyses of thermal storage concrete modules

A three-stage study on the behaviour of storage plants employing concrete with upgraded thermo-mechanical characteristics is here developed. The first stage defines the experimental campaign on a mixing at improved conductivity, via the SolTeCa experimental system, with review of the storage elements geometry, location of thermocouples and cycling procedures. The experimental results, obtained by ENEA via a comparison with appropriately performed numerical calculations, are interpreted during the second stage. Finally, a first design of a new equipment for the thermal cycling of storage elements up to 400 \ub0C is proposed, based on Joule-effect heating. The numerical results are reported, in order to understand the thermal dynamics as well as the induced thermo-mechanical effects on concrete elements

Highly efficient photoanodes for dye solar cells with a hierarchical meso-ordered structure

An engineered bi-layered photoelectrode for dye solar cells has been developed which profitably employs two synergistic meso-ordered components, namely a thin meso-ordered TiO2 film and a main microparticles-based photoelectrode. The former has been deposited as an interfacial layer at the FTO-coated substrate and suppresses the back-transport reaction by blocking direct contact between the electrolyte and conductive oxide. The latter is made of hierarchical micro- and nano-structured building blocks prepared by template synthesis, which permits efficient light scattering without sacrificing the internal surface area. The optimization of light harvesting and charge recombination dynamics allowed us to achieve as high energy conversion efficiency as 9.7%

High-quality photoelectrodes based on shape-tailored TiO2 nanocrystals for dye-sensitized solar cells

We demonstrate a general approach by which colloidal anatase TiO2 nanocrystals with anisotropically tailored linear and branched shapes can safely be processed into high-quality mesoporous photoelectrodes for dye-sensitized solar cells. A detailed study has been carried out to elucidate how the nanoscale architecture underlying the photoelectrodes impacts their ultimate performances. From the anal. of the most relevant electrochem. parameters, an intrinsic correlation between the photovoltaic performances and the structure of the nanocrystal building blocks has been deduced and explained on the basis of relative contributions of the electron transport and light-harvesting properties of the photoelectrodes. Depending on the nanocrystals incorporated, these devices can exhibit an energy conversion efficiency of 5.2-7.8%, which ranks 38-53% higher than that achievable with corresponding cells based on ref. spherical nanoparticles. It has been ascertained that dye-sensitized solar cells based on high aspect-ratio linear nanorods allow for a remarkable improvement in the charge-collection efficiency due to minimization of detrimental charge-recombination processes at the photoelectrode/electrolyte interface. On the other hand, dye-sensitized solar cells fabricated from branched nanocrystals with a peculiar bundle-like configuration are characterized by a drastic redn. of undesired charge-trapping phenomena. These findings can be useful in the design and fabrication of future generations of high-performing dye-sensitized solar cells based on colloidal nanocrystals with properly engineered size and shape parameters