Circuit controls transients in SCR inverters

Elimination of starting difficulties in SCR inverters is accomplished by the addition of two taps of the output winding of the inverter. On starting or under transient loads, the two additional taps deliver power through diodes without requiring quenching of SCR currents in excess of normal starting load

Research on spacecraft electrical power conversion

The history of spacecraft electrical power conversion in literature, research and practice is reviewed. It is noted that the design techniques, analyses and understanding which were developed make today's contribution to power computers and communication installations. New applications which require more power, improved dynamic response, greater reliability, and lower cost are outlined. The switching mode approach in electronic power conditioning is discussed. Technical aspects of the research are summarized

Research on spacecraft electrical power conversion

The steady state characteristics and starting behavior of some widely used self-oscillating magnetically coupled square wave inverters were studied and the development of LC-tuned square wave inverters is reported. An analysis on high amplitude voltage spikes which occur in dc-to-square-wave parallel converters shows the importance of various circuit parameters for inverter design and for the suppression of spikes. A computerized simulation of an inductor energy storage dc-to-dc converter with closed loop regulators and of a preregulating current step-up converter are detailed. Work continued on the computer aided design of two-winding energy storage dc-to-dc converters

Power conditioning - inversion, conversion, and regulation

Switching element requirements for spacecraft electric power conversion, inversion, and regulatio

Structural and electronic properties of MgO nanotube clusters

Finite magnesium oxide nanotubes are investigated. Stacks of four parallel squares, hexagons, octagons, and decagons are constructed and studied by the pseudopotential density functional theory within the local-density approximation. Optimized structures are slightly distorted stacks of polygons. These clusters are insulators and the band gap of 8.5 eV is constant over an investigated range of the diameters of stacked polygonal rings. Using the L"owdin population analysis a charge transfer towards the oxygen atoms is estimated as 1.4, which indicates that the mixed ionocovalent bonding exists in investigated MgO nanotubes

Temperature automation for a propellant mixer

The analysis and installation of an automatic temperature controller on a propellant mixer is presented. Ultimately, the entire mixing process will come under automation, but since precise adherence to the temperature profile is very difficult to sustain manually, this was the first component to be automated. Automation is not only important for producing a uniform product, but it is necessary for envisioned space-based propellant production

A dc model for power switching transistors suitable for computer-aided design and analysis

A model for bipolar junction power switching transistors whose parameters can be readily obtained by the circuit design engineer, and which can be conveniently incorporated into standard computer-based circuit analysis programs is presented. This formulation results from measurements which may be made with standard laboratory equipment. Measurement procedures, as well as a comparison between actual and computed results, are presented

High-frequency high-voltage high-power DC-to-DC converters

The current and voltage waveshapes associated with the power transitor and the power diode in an example current-or-voltage step-up (buck-boost) converter were analyzed to highlight the problems and possible tradeoffs involved in the design of high voltage high power converters operating at switching frequencies in the range of 100 Khz. Although the fast switching speeds of currently available power diodes and transistors permit converter operation at high switching frequencies, the resulting time rates of changes of current coupled with parasitic inductances in series with the semiconductor switches, produce large repetitive voltage transients across the semiconductor switches, potentially far in excess of the device voltage ratings. The need is established for semiconductor switch protection circuitry to control the peak voltages appearing across the semiconductor switches, as well as to provide the waveshaping action require for a given semiconductor device. The possible tradeoffs, as well as the factors affecting the tradeoffs that must be considered in order to maximize the efficiency of the converters are enumerated

Analysis of transistor and snubber turn-off dynamics in high-frequency high-voltage high-power converters

Dc to dc converters which operate reliably and efficiently at switching frequencies high enough to effect substantial reductions in the size and weight of converter energy storage elements are studied. A two winding current or voltage stepup (buck boost) dc-to-dc converter power stage submodule designed to operate in the 2.5-kW range, with an input voltage range of 110 to 180 V dc, and an output voltage of 250 V dc is emphasized. In order to assess the limitations of present day component and circuit technologies, a design goal switching frequency of 10 kHz was maintained. The converter design requirements represent a unique combination of high frequency, high voltage, and high power operation. The turn off dynamics of the primary circuit power switching transistor and its associated turn off snubber circuitry are investigated

Development of a 1.6-kW, 2000-volt, high- frequency dc-dc converter for ion thrustors using a modular design and an inductive energy pumping technique for conversion, regulation and protection Summary report

High-frequency dc-dc converter for ion thrustors using modular design and inductive energy pumping technique for conversion, regulation, and protectio