Simulation of Fluid Flow and Collection Efficiency for an SEA Multi-element Probe

Numerical simulations of fluid flow and collection efficiency for a Science Engineering Associates (SEA) multi-element probe are presented. Simulation of the flow field was produced using the Glenn-HT Navier-Stokes solver. Three dimensional unsteady results were produced and then time averaged for the collection efficiency results. Three grid densities were investigated to enable an assessment of grid dependence. Collection efficiencies were generated for three spherical particle sizes, 100, 20, and 5 micron in diameter, using the codes LEWICE3D and LEWICE2D. The free stream Mach number was 0.27, representing a velocity of approximately 86 ms. It was observed that a reduction in velocity of about 15-20 occurred as the flow entered the shroud of the probe.Collection efficiency results indicate a reduction in collection efficiency as particle size is reduced. The reduction with particle size is expected, however, the results tended to be lower than previous results generated for isolated two-dimensional elements. The deviation from the two-dimensional results is more pronounced for the smaller particles and is likely due to the effect of the protective shroud

A Thermal Analysis of a Hot-Wire Probe for Icing Applications

This paper presents a steady-state thermal model of a hot-wire instrument applicable to atmospheric measurement of water content in clouds. In this application, the power required to maintain the wire at a given temperature is used to deduce the water content of the cloud. The model considers electrical resistive heating, axial conduction, convection to the flow, radiation to the surroundings, as well as energy loss due to the heating, melting, and evaporation of impinging liquid and or ice. All of these parameters can be varied axially along the wire. The model further introduces a parameter called the evaporation potential which locally gauges the maximum fraction of incoming water that evaporates. The primary outputs of the model are the steady-state power required to maintain a spatially-average constant temperature as well as the variation of that temperature and other parameters along the wire. The model is used to understand the sensitivity of the hot-wire performance to various flow and boundary conditions including a detailed comparison of dry air and wet (i.e. cloud-on) conditions. The steady-state power values are compared to experimental results from a Science Engineering Associates (SEA) Multi-Element probe, a commonly used water-content measurement instrument. The model results show good agreement with experiment for both dry and cloud-on conditions with liquid water content. For ice, the experimental measurements under read the actual water content due to incomplete evaporation and splashing. Model results, which account for incomplete evaporation, are still higher than experimental results where the discrepancy is attributed to splashing mass-loss which is not accounted in the model

A Three-Component Gene Expression System and Its Application for Inducible Flavonoid Overproduction in Transgenic Arabidopsis thaliana

Inducible gene expression is a powerful tool to study and engineer genes whose overexpression could be detrimental for the host organisms. However, only limited systems have been adopted in plant biotechnology. We have developed an osmotically inducible system using three components of plant origin, RD29a (Responsive to Dehydration 29A) promoter, CBF3 (C-repeat Binding Factor 3) transcription factor and cpl1-2 (CTD phosphatase-like 1) mutation. The osmotic stress responsible RD29a promoter contains the CBF3 binding sites and thus RD29A-CBF3 feedforward cassette enhances induction of RD29a promoter under stress. The cpl1-2 mutation in a host repressor CPL1 promotes stress responsible RD29a promoter expression. The efficacy of this system was tested using PAP1 (Production of Anthocyanin Pigment 1) transgene, a model transcription factor that regulates the anthocyanin pathway in Arabidopsis. While transgenic plants with only one or two of three components did not reproducibly accumulate anthocyanin pigments above the control level, transgenic cpl1 plants containing homozygous RD29a-PAP1 and RD29a-CBF3 transgenes produced 30-fold higher level of total anthocyanins than control plants upon cold treatment. Growth retardation and phytochemical production of transgenic plants were minimum under normal conditions. The flavonoid profile in cold-induced transgenic plants was determined by LC/MS/MS, which resembled that of previously reported pap1-D plants but enriched for kaempferol derivatives. These results establish the functionality of the inducible three-component gene expression system in plant metabolic engineering. Furthermore, we show that PAP1 and environmental signals synergistically regulate the flavonoid pathway to produce a unique flavonoid blend that has not been produced by PAP1 overexpression or cold treatment alone

Development and commissioning of a linear compressor cascade rig for ice crystal research

This paper describes the commissioning of a linear compressor cascade rig for ice crystal research. The rig is located in an altitude chamber so the test section stagnation pressure, temperature and Mach number can be varied independently. The facility is open-circuit which eliminates the possibility of recirculating ice crystals reentering the test section and modifying the median mass diameter and total water content in time. As this is an innovative facility, the operating procedures and instrumentation used are discussed. Sample flow quality data are presented showing the distribution of velocity, temperature, turbulence intensity and ice water concentration in the test section. The control and repeatability of experimental parameters is also discussed. Although the rig was designed to investigate the ice crystal phenomenon in an environment representative of a compressor stator row, the test section can be reconfigured to assess the performance of aircraft air data sensors as well.Peer reviewed: YesNRC publication: Ye

Altitude scaling of ice crystal accretion

This paper describes experiments performed in an altitude chamber at the National Research Council of Canada (NRC) as the first step towards developing altitude scaling laws and procedures that will possibly allow aero-engines to be certified for operation in ice crystal clouds at high altitude by testing in sea level facilities. The principal objective was to test the hypothesis that accretion within a compressor due to ice crystal ingestion occurs when the local ratio of freestream liquid water content (LWC) to total water content (TWC) lies within a critical range at an accretion-susceptible location. If this hypothesis is correct, the local LWC/TWC ratio is the key parameter that must be matched in tests at low and high pressures to match accretions. Experiments were conducted in a small wind tunnel with an axisymmetric test article, consisting of a hemispherical nose attached to a conical afterbody, at a fixed TWC over a range of LWC/TWC ratios at (absolute) pressures of 34.5 kPa and 69 kPa to test the hypothesis. The LWC/TWC ratio was varied by changing the wet bulb temperature. Accretion steady-state volumes and growth rates measured at the two pressures were compared at conditions which were analytically predicted to produce matched LWC/TWC ratios. Good agreement was achieved in all cases. Accretion growth was greatest for LWC/TWC ratios in the range 10-25%. Additional tests demonstrated that wet bulb temperature, which was identified as an important variable in earlier studies, had little influence on accretion growth beyond its effect on LWC/TWC (i.e. ice particle melting). Tests were also conducted to determine whether accretion growth scales linearly with TWC at constant LWC/TWC. Those tests confirmed that not only does the accretion growth rate in the early growth phase scale in direct proportion to TWC, but so does the final size of the accretion. A simple semi-empirical model for predicting this behavior is described. While most of the tests were conducted with an ice particle median volumetric diameter of 45\u3bc, some of the scaling tests were repeated with larger particles, which produced smaller accretions. \ua9 2013 by Her Majesty the Queen in Right of Canada. Published by the American Institute of Aeronautics and Astronautics.Peer reviewed: YesNRC publication: Ye

Particle size effects on ice crystal accretion

This paper describes the commissioning of a new test apparatus intended to simulate an inner-compressor duct bleed slot. It also identifies, for the first time, that ice crystal particle size plays an important role in the ice crystal phenomenon. Data and sample images of accretion are presented for wet bulb temperatures near freezing. The effect of wet bulb temperature and particle size on the natural melting of ice crystals is investigated. In addition, the erosion of surface accretion by ice crystal particles is discussed. \ua9 2012 by Her Majesty the Queen in Right of Canada. Published by the American Institute of Aeronautics and Astronautics, Inc.Peer reviewed: YesNRC publication: Ye

Particle size effects on ice crystal accretion - Part II

This paper describes ongoing research intended to simulate ice accretion in an inter-compressor duct bleed slot resulting from the ingestion of altitude ice crystals. The authors have previously shown that ice crystal particle size plays an important role in the ice crystal accretion phenomenon. It was also shown that ice crystal particle size affects the degree of natural melt that occurs for a given aerodynamic condition. The data presented herein decouples the effects of ice particle melt and particle size distribution to generate accretions with the same ratio of freestream liquid-to-total water fraction. The effects of wet bulb temperature and ice particle size on the natural melting of ice crystals are discussed. An ice preservation procedure is followed to allow tracings of the accretion to be taken along the test article. Ice crystal particle size distribution is characterized using a shadowgraphy imaging technique. Finally, the reduction in accretion rate relative to the theoretical maximum rate of surface accretion by ice crystal particles is discussed. The test article simulates a forward facing, inclined endwall bleed slot in a gas turbine compressor as a simplified two-dimensional representation. The geometry, having a surface inclined 20\ub0 to the incoming flow, proved to be susceptible to mixed phase ice crystal accretion. Particle size and particularly the large particle tail of the distribution had a significant impact on the magnitude of accretion under mixed phase test conditions for wet bulb temperatures above and below 0\ub0C. The leading edge growth rates were found to be 1/4 to 1/9 of the theoretical growth rate suggesting that erosion, splashing, particle bounce and other loss mechanism rates are significant. The ice tracings were used to estimate an accretion mass for a hypothetical large bypass ratio gas turbine. It was found that approximately 4kg of ice could be generated should the inter-compressor duct be exposed to the conditions tested for 5 minutes. \ua9 2013 by Her Majesty the Queen in Right of Canada. Published by the American Institute of Aeronautics and Astronautics.Peer reviewed: YesNRC publication: Ye