Illumination and annealing characteristics of two-dimensional electron gas systems in metal-organic vapor-phase epitaxy grown AlGaN/AlN/GaN heterostructures

We studied the persistent photoconductivity (PPC) effect in AlGaN/AlN/GaN heterostructures with two different Al-compositions (x=0.15 and x=0.25). The two-dimensional electron gas formed at the AlN/GaN heterointerface was characterized by Shubnikov-de Haas and Hall measurements. Using optical illumination, we were able to increase the carrier density of the Al0.15Ga0.85N/AlN/GaN sample from 1.6x10^{12} cm^{-2} to 5.9x1012 cm^{-2}, while the electron mobility was enhanced from 9540 cm2/Vs to 21400 cm2/Vs at T = 1.6 K. The persistent photocurrent in both samples exhibited a strong dependence on illumination wavelength, being highest close to the bandgap and decreasing at longer wavelengths. The PPC effect became fairly weak for illumination wavelengths longer than 530 nm and showed a more complex response with an initial negative photoconductivity in the infrared region of the spectrum (>700 nm). The maximum PPC-efficiency for 390 nm illumination was 0.011% and 0.005% for Al0.25Ga0.75N/AlN/GaN and Al0.15Ga0.85N/AlN/GaN samples, respectively. After illumination, the carrier density could be reduced by annealing the sample. Annealing characteristics of the PPC effect were studied in the 20-280 K temperature range. We found that annealing at 280 K was not sufficient for full recovery of the carrier density. In fact, the PPC effect occurs in these samples even at room temperature. Comparing the measurement results of two samples, the Al0.25Ga0.75N/AlN/GaN sample had a larger response to illumination and displayed a smaller recovery with thermal annealing. This result suggests that the energy scales of the defect configuration-coordinate diagrams for these samples are different, depending on their Al-composition.Comment: 27 pages, 8 figure

Metamaterial with polarization and direction insensitive resonant transmission response mimicking electromagnetically induced transparency

We report on a planar metamaterial, the resonant transmission frequency of which does not depend on the polarization and angle of incidence of electromagnetic waves. The resonance results from the excitation of high-Q antisymmetric trapped current mode and shows sharp phase dispersion characteristic to Fano-type resonances of the electromagnetically induced transparency phenomenon

Spin-Wave and Electromagnon Dispersions in Multiferroic MnWO4 as Observed by Neutron Spectroscopy: Isotropic Heisenberg Exchange versus Anisotropic Dzyaloshinskii-Moriya Interaction

High resolution inelastic neutron scattering reveals that the elementary magnetic excitations in multiferroic MnWO4 consist of low energy dispersive electromagnons in addition to the well-known spin-wave excitations. The latter can well be modeled by a Heisenberg Hamiltonian with magnetic exchange coupling extending to the 12th nearest neighbor. They exhibit a spin-wave gap of 0.61(1) meV. Two electromagnon branches appear at lower energies of 0.07(1) meV and 0.45(1) meV at the zone center. They reflect the dynamic magnetoelectric coupling and persist in both, the collinear magnetic and paraelectric AF1 phase, and the spin spiral ferroelectric AF2 phase. These excitations are associated with the Dzyaloshinskii-Moriya exchange interaction, which is significant due to the rather large spin-orbit coupling.Comment: 8 pages, 6 figures, accepted for publication in Physical Review

Additive manufacturing of Ti-6Al-4V alloy by micro-laser metal wire deposition with pulsed wave emission: processability and microstructure formation

In this work, the micro-laser metal wire deposition (μLMWD) with ms-pulsed wave emission and low duty cycles was utilized to build the Ti-6Al-4V thin walls. The work first investigated the influence of the process parameters on single track stability and geometry. With the developed processing conditions thin walls with multiple layers were produced. The μLMWD produced thin walls were characterized by fine grain size expected to be due to the columnar to equiaxed transition (CET) in the produced wall. Fine columnar grains formed in the bottom region of wall due to the restriction of melt pool size and large cooling speed, while equiaxed grain formation and further refinement were achieved in the middle region, attributed to the intermittent stirring force that broke dendritic arms and increased nucleation events before solid–liquid interface. From the bottom to top region microstructures transferred from acicular α′ to short α lamella constituting basketweave structure, and the periodic heating and cooling generating by pulsed laser reduced the acicular α′ at higher cooling rate and decreased α size. The forming of equiaxed grain and fine grain and microstructure increased the wall microhardness

MRI-based Surgical Planning for Lumbar Spinal Stenosis

The most common reason for spinal surgery in elderly patients is lumbar spinal stenosis(LSS). For LSS, treatment decisions based on clinical and radiological information as well as personal experience of the surgeon shows large variance. Thus a standardized support system is of high value for a more objective and reproducible decision. In this work, we develop an automated algorithm to localize the stenosis causing the symptoms of the patient in magnetic resonance imaging (MRI). With 22 MRI features of each of five spinal levels of 321 patients, we show it is possible to predict the location of lesion triggering the symptoms. To support this hypothesis, we conduct an automated analysis of labeled and unlabeled MRI scans extracted from 788 patients. We confirm quantitatively the importance of radiological information and provide an algorithmic pipeline for working with raw MRI scans

Critical frontier for the Potts and percolation models on triangular-type and kagome-type lattices II: Numerical analysis

In a recent paper (arXiv:0911.2514), one of us (FYW) considered the Potts model and bond and site percolation on two general classes of two-dimensional lattices, the triangular-type and kagome-type lattices, and obtained closed-form expressions for the critical frontier with applications to various lattice models. For the triangular-type lattices Wu's result is exact, and for the kagome-type lattices Wu's expression is under a homogeneity assumption. The purpose of the present paper is two-fold: First, an essential step in Wu's analysis is the derivation of lattice-dependent constants $A, B, C$ for various lattice models, a process which can be tedious. We present here a derivation of these constants for subnet networks using a computer algorithm. Secondly, by means of a finite-size scaling analysis based on numerical transfer matrix calculations, we deduce critical properties and critical thresholds of various models and assess the accuracy of the homogeneity assumption. Specifically, we analyze the $q$-state Potts model and the bond percolation on the 3-12 and kagome-type subnet lattices $(n\times n):(n\times n)$, $n\leq 4$, for which the exact solution is not known. To calibrate the accuracy of the finite-size procedure, we apply the same numerical analysis to models for which the exact critical frontiers are known. The comparison of numerical and exact results shows that our numerical determination of critical thresholds is accurate to 7 or 8 significant digits. This in turn infers that the homogeneity assumption determines critical frontiers with an accuracy of 5 decimal places or higher. Finally, we also obtained the exact percolation thresholds for site percolation on kagome-type subnet lattices $(1\times 1):(n\times n)$ for $1\leq n \leq 6$.Comment: 31 pages,8 figure