Effect of surface treatments on the bond strength of a resin cement to commercially pure titanium

Investigation of the effectiveness of surface treatments that promote a strong bond strength of resin cements to metals can contribute significantly to the longevity of metal-ceramic restorations. This study evaluated the effect of surface treatments on the shear bond strength (SBS) of a resin cement to commercially pure titanium (CP Ti). Ninety cast CP Ti discs were divided into 3 groups (n=30), which received one of the following airborne-particle abrasion conditions: (1) 50 μm Al2O3 particles; (2) 30 μm silica-modified Al2O3 particles (Cojet Sand); (3) 110 μm silica-modified Al2O3 particles (Rocatec). For each airborne-particle abrasion condition, the following post-airborne-particle abrasion treatments were used (n=10): (1) none; (2) adhesive Adper Single Bond 2; (3) silane RelyX Ceramic Primer. RelyX ARC resin cement was bonded to CP Ti surfaces. All specimens were thermally cycled before being tested in shear mode. Failure mode was determined. The best association was Rocatec plus silane. All groups showed 100% adhesive failure. There were combinations that promote higher SBS than the protocol recommended by the manufacturer of RelyX ARC

Air abrasion before and/or after zirconia sintering: surface characterization, flexural strength, and resin cement bond strength

The purpose of this in vitro study was to evaluate the effect of air-abrasion/zirconia sintering order on the yttria partially stabilized tetragonal zirconia polycrystal (Y-TZP) surface characterization (roughness, morphology, and phase transformation), flexural strength (FS), and shear bond strength (SBS) to a resin cement. Y-TZP specimens were air abraded with 50-μm Al2O3 particles after (AS), before (BS), or before and after zirconia sintering (BAS). For roughness (Ra), 30 block specimens (12×12×3.0 mm; n=10) had their surfaces analyzed by a profilometer. Next, on the air-abraded surfaces of these specimens, composite resin discs (n=30) were bonded with RelyX ARC. The bonded specimens were stored for 24 hours in distilled water at 37°C before shear testing. Failure mode was determined with a stereomicroscope (20×). The surface morphology (n=2) was evaluated by SEM (500×). For the four-point flexural strength test (EMIC DL2000), 39 bar-shaped specimens (20×4.0×1.2 mm; n=13) were air abraded according to the three conditions proposed, and an additional group (nonabraded) was evaluated (n=13). The quantitative analysis of phase transformation (n=1) was completed with Rietveld refinement with X-ray diffraction data. Ra (μm) and SBS (MPa) data were analyzed by one-way analysis of variance (ANOVA) and the Tukey test (α=0.05). Pearson correlation analysis was used to determine if there was a correlation between roughness and SBS. For FS (MPa) data, one-way ANOVA and the Dunnett C-test (α=0.05) were used. The air-abrasion/zirconia sintering order influenced significantly (p<0.001) Ra, SBS, and FS. The BS and AS groups presented the highest (1.3 μm) and the lowest (0.7 μm) Ra. The highest SBS (7.0 MPa) was exhibited by the BAS group, followed by the AS group (5.4 MPa) and finally by the BS group (2.6 MPa). All groups presented 100% adhesive failure. A weak correlation (r=−0.45, p<0.05) was found between roughness and SBS. The air-abrasion/zirconia sintering order provided differences in the surface morphology. The nonabraded (926.8 MPa) and BS (816.3 MPa) groups exhibited statistically similar FS values but lower values than the AS (1249.1 MPa) and BAS (1181.4 MPa) groups, with no significant difference between them. The nonabraded, AS, BS, and BAS groups exhibited, respectively, percentages of monoclinic phase of 0.0 wt%, 12.2 wt%, 0.0 wt%, and 8.6 wt%. The rougher surface provided by the air-abrasion before zirconia sintering may have impaired the bonding with the resin cement. The morphological patterns were consistent with the surface roughness. Considering the short-term SBS and FS, the BAS group exhibited the best performance. Air abrasion, regardless of its performance order, provides tetragonal to monoclinic transformation, while sintering tends to zero the monoclinic phase content

O papel da integração regional para o Brasil: universalismo, soberania e percepção das elites The role of regional integration for Brazil: universalism, sovereignty, autonomy and elites' perception

O objetivo deste trabalho é analisar o significado do Mercosul para a política exterior do Brasil. Para isso, discutiremos as percepções das elites brasileiras em relação ao processo de integração regional. A defesa do princípio da intergovernamentalidade está ligada à concepção do lugar do Mercosul nas relações internacionais do país. A grande valorização de princípios como o do universalismo e o de soberania acaba afetando o aprofundamento da integração. A hipótese deste trabalho é que a estrutura do Mercosul seria condizente com as percepções de parte das elites brasileiras. Argumentaremos que a estrutura atual é insuficiente para garantir a dinâmica da integração.<br>The aim of this article is to analyse the role of Mercosur for the Brazilian foreign policy. We will discuss the perception of the Brazilian elites concerning the regional integration process. The defense of the principle of intergovernmentalism is related to the conception of Mercosur's place in the set of Brazilian international relations. The huge valuation of some principles, as universalism and sovereignty, ends up by affecting the deepening of integration. The hypothesis of this paper is that the Mercosur structure would be related with part of Brazilian elite's perceptions. Our argument is that the current structure is insufficient to guarantee the dynamics of the integration

Ciclos longos e cenários contemporâneos da sociedade internacional Long cycles of the international society

A despeito da anarquia que resulta da ausência uma autoridade legítima comum, as relações internacionais pós-Westphalia têm elementos de ordem que são suficientes para caracterizá-las como uma forma de "associação prática". Esses elementos são a (igual) soberania nacional, a diplomacia, o direito internacional e o equilíbrio de poder. Discute-se, neste artigo, em que medida esses pilares da ordem mundial pós-Westphalia ainda se prestam para pensar as relações internacionais no pós-Guerra Fria. Trata-se de saber em que medida essas relações hoje se afastam do modelo de "associação prática" em direção a um modelo, normativamente mais exigente, de "associação de objetivos".<br>Despite the lack of a common legitimate authority the international relations after Westphalia share enough elements of order for being characterized as a form of "practical association": (equal) national sovereignty, diplomacy, international law and the balance of power. The fit-ness of those pilars of the post-Westphalian world order for thinking the international relations after the Cold War is discussed. It is asked how far those relations are leaving the model of a practical association towards another normatively more demanding model, of "goals association"