24 research outputs found
First EMC3-EIRENE Simulations with Divertor Legs of LHD in Realistic Device Geometry
An extended mesh system for EMC3-EIRENE has been developed to simulate peripheral plasma including the ergodic and the divertor leg regions of LHD. Both the open and the closed divertor configurations are available. A series of simulations for 8MW input power, five different electron densities at the LCFS (last closed flux surface) and the open/closed configurations were carried out. Approximately 10 times larger neutral pressure was observed under the dome structure compared with the open configuration, which is in good agreement with experimental measurements. In the case of the closed configuration, the leg regions have a large contribution of ionization to hydrogen recycling. In the case of high density discharges, however, electron temperature in the legs becomes low and the major contribution of ionization moves to the ergodic region. Significant influence of configurations is observed in the inboard side of LHD, where closed divertor components are installed but little influence is seen near the LCFS. (© 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim
Investigation of heat flux deposition on divertor target on the Large Helical Device with EMC3-EIRENE modelling
The measured divertor heat flux profiles are compared to the EMC3-EIRENE simulations for two different times of an LHD discharge, corresponding to higher and lower edge temperatures. The relation between the three-dimensional magnetic field structure and the heat flux distributions on the divertor has been analysed. The modelled heat flux for the lower plasma temperature case has a better agreement with the experimental result obtained by the Langmuir probes, which shows a qualitative reproduction of the experimental profile shape. However, the heat flux distribution for the high plasma temperature case shows a different behaviour between the simulation results and the experimental measurements. The detailed analysis of the heat flux distribution for the higher temperature case which has a larger discrepancy has been performed, both quantitatively and qualitatively. The radiation of the eroded impurity from divertor target plates has a minor effect on the heat flux distribution. Non-uniform cross-field transport coefficients are used in the simulations and its impact on the heat flux distributions is discussed for the case of the high plasma temperature
Three-dimensional impurity transport modeling of neon-seeded and nitrogen-seeded LHD plasmas
Modeling of impurity-seeded plasma in Large Helical Device is presented for the first time by using the three-dimensional transport code EMC3-EIRENE. High and low recycling coefficients for impurity ions are assumed to include low and high absorption rates on wall surfaces due to low and high chemical activity of neon and nitrogen, respectively. Radiation power measured by two bolometer systems and particle flux measured by divertor probes installed in multiple toroidal sections are utilized to determine impurity amount in the plasma. The toroidal uniformity and the non-uniformity of a divertor flux reduction observed experimentally for neon and nitrogen seeding, respectively, are reproduced by the model. Validations by measurements and deviations between the model and the experiment are discussed
Plasma and Neutral Transport Study of Local Island Divertor Configuration in Large Helical Device Edge Region with 3D Monte Carlo Codes
Edge transport physics of the Local Island Divertor (LID) configuration in Large Helical Device (LHD) is studied with the 3D transport code package, EMC3-EIRENE [Y. Feng et al., Contrib. Plasma Phys. 44, 57 (2004)] [D. Reiter, Technical Report Jul-1947, KFA Juelich, Germany (1984)]. Particularly, the behaviour of neutrals around the divertor region was investigated, where it was found that the resulting profiles of atom andmolecular density as well as temperature are considerably different each other. The cause of these difference is discussed
Plasma and Neutral Transport Study of Local Island Divertor Configuration in Large Helical Device Edge Region with 3D Monte Carlo Codes
Iron-Imprinted Single-Atomic Site Catalyst-Based Nanoprobe for Detection of Hydrogen Peroxide in Living Cells
Abstract Fe-based single-atomic site catalysts (SASCs), with the natural metalloproteases-like active site structure, have attracted widespread attention in biocatalysis and biosensing. Precisely, controlling the isolated single-atom Fe-N-C active site structure is crucial to improve the SASCs’ performance. In this work, we use a facile ion-imprinting method (IIM) to synthesize isolated Fe-N-C single-atomic site catalysts (IIM-Fe-SASC). With this method, the ion-imprinting process can precisely control ion at the atomic level and form numerous well-defined single-atomic Fe-N-C sites. The IIM-Fe-SASC shows better peroxidase-like activities than that of non-imprinted references. Due to its excellent properties, IIM-Fe-SASC is an ideal nanoprobe used in the colorimetric biosensing of hydrogen peroxide (H2O2). Using IIM-Fe-SASC as the nanoprobe, in situ detection of H2O2 generated from MDA-MB-231 cells has been successfully demonstrated with satisfactory sensitivity and specificity. This work opens a novel and easy route in designing advanced SASC and provides a sensitive tool for intracellular H2O2 detection
Comparison of Observed Divertor Heat Flux and Modeling Results at LHD
The divertor strike line pattern on the helical divertor of LHD was observed with an infra red camera. The derived heat flux pattern show multiple distinct strike lines depending on the equilibrium magnetic configuration. Predictions of such divertor heat loads thus require a modeling of the magnetic configuration and the heat transport in the magnetic edge. Equilibrium magnetic topologies were analyzed with HINT2, while the plasma fluid model code EMC3 was used to simulate the energy transport in the edge. The measured multi peak structure of the divertor heat flux is correlated to the intersection points of elongated loop shaped flux tubes of long LC field lines. But the fluid model could not recreate the total energy load and the multiple heat flux peaks on the divertor. A Variation in the plasma density ne as a transport parameter in order to fit the simulated heat flux to the measured one shows a contradicting tendency