59 research outputs found
Recommended from our members
Absorption of short-pulse electromagnetic energy by a resistively loaded straight wire
Absorption of short-pulse electromagnetic energy by a resistively loaded straight wire is examined. Energy collected by the wire, load energy, peak load currents, and peak load voltages are found for a wide range of parameters, with particular emphasis on nuclear electromagnetic pulse (EMP) phenomena. A series of time-sequenced plots is used to illustrate pulse propagation on wires when loads and wire ends are encountered. (auth
Recommended from our members
LLL transient-electromagnetics-measurement facility
The operation and hardware of the Lawrence Livermore Laboratory's transient-electromagnetics (EM)-measurement facility are described. The transient-EM range is useful for determining the time-domain transient responses of structures to incident EM pulses. To illustrate the accuracy and utility of the EM-measurement facility, actual experimental measurements are compared to numerically computed values. (auth
Absorption of short-pulse electromagnetic energy by a resistively loaded straight wire
Absorption of short-pulse electromagnetic energy by a resistively loaded straight wire is examined. Energy collected by the wire, load energy, peak load currents, and peak load voltages are found for a wide range of parameters, with particular emphasis on nuclear electromagnetic pulse (EMP) phenomena. A series of time-sequenced plots is used to illustrate pulse propagation on wires when loads and wire ends are encountered. (auth
Recommended from our members
Development of beam position monitors for heavy ion recirculators
Work is underway at the Lawrence Livermore National Laboratory to design and build a small-scale, heavy ion recirculating induction accelerator. An essential part of this design work is the development of small nonintercepting diagnostics to measure beam current and position. This paper describes some of this work, with particular emphasis on the development of a small capacitive probe beam position monitor to resolve beam position to the 100 {mu}m level in a 6 cm diameter beam pipe. Initial measured results with an 80 keV potassium ion beam are presented
Recommended from our members
Probabilistic approach to EMP assessment
The development of nuclear EMP hardness requirements must account for uncertainties in the environment, in interaction and coupling, and in the susceptibility of subsystems and components. Typical uncertainties of the last two kinds are briefly summarized, and an assessment methodology is outlined, based on a probabilistic approach that encompasses the basic concepts of reliability. It is suggested that statements of survivability be made compatible with system reliability. Validation of the approach taken for simple antenna/circuit systems is performed with experiments and calculations that involve a Transient Electromagnetic Range, numerical antenna modeling, separate device failure data, and a failure analysis computer program
A systems study of an RF power source for a 1 TeV next linear collider based upon the relativistic-klystron two-beam accelerator
Performance results of the high-gain Nd:glass engineering prototype preamplifier module (PAM) for the National Ignition Facility (NIF)
We describe recent, energetics performance results on the engineering preamplifier module (PAM) prototype located in the front end of the 1.8MJ National Ignition Facility (NIF) laser system. Three vertically mounted subsystem located in the PAM provide laser gain as well as spatial beam shaping. The first subsystem in the PAM prototype is a diode pumped, Nd:glass, linear, TEM{sub 00}, 4.5m long regenerative amplifier cavity. With a single diode pumped head, we amplify a 1nJ, mode matched, temporally shaped ({approx} 20ns) seed pulse by a factor of approximately 10{sup 7} to 20mJ. The second subsystem in the PAM is the beam shaping module, which magnifies the gaussian output beam of the regenerative amplifier to provide a 30mm x 30mm square beam that is spatially shaped in two dimensions to pre-compensate for radial gain profiles in the main amplifiers. The final subsystem in the PAM is the 4-pass amplifier which relay images the 1mJ output of the beam shaper through four gain passes in a {phi}5cm x 48cm flashlamp pumped rod amplifier, amplifying the energy to 175. The system gain of the PAM is 10{sup 10}. Each PAM provides 35 of injected energy to four separate main amplifier chains which in turn delivers 1.8MJ in 192 frequency converted laser beams to the target for a broad range of laser fusion experiments
Recommended from our members
Electrical grounding, shielding, and isolation for the MFTF-B plasma diagnostic system
The electrical grounding, shielding, and isolation of plasma diagnostics on the Mirror Fusion Test Facility (MFTF-B) is a key part of the overall design. The Electromagnetic Interference (EMI) environment in which the Plasma Diagnostics System (PDS) will be required to operate is very harsh. The electrical grounding and shielding design which is being implemented to cope with this environment follows one which has been used successfully on the Tandem Mirror Experiment (TMX). Details of the MFTF-B plasma diagnostics facility, equipment grounding, shielding and isolation, and the cabling system are described in this paper
- …