Development, Validation, and Reliability Evaluation of a Functional Classification System

Due to accountability, cost/benefit, and third party payers, it was necessary to develop an objective measurement of functional abilities of rehab patients. In Part I of the research, Development of a Functional Classification System for a Rehabilitation Unit at St. Alexius Medical Center, a Functional Classification System (FCS) was developed and edited; however, the validity and reliability of the new FCS had to be justified. Forty-seven patients admitted onto the St. Alexius Rehabilitation Unit between November 1992 and January 1993 were evaluated using version three of the FCS and objectively scored. Validity was tested between admit, discharge, and goal scores with a Pearson Correlation Coefficient of 0.8224 (moderately high) between admit and goal scores. The FCS scores were in a hierarchy fashion which is proper progression of a scoring instrument measuring progress. Content validity was found by use of a scale of one to five with one being agree and five disagree. The professionals agreed that the FCS did a good job of objectively measuring patient\u27s status. Inter-rater reliability was found by randomly selecting eleven of the forty seven patients and then comparing three parameter scores: Grooming, Eating, and Transfers. The scores were scored between inter-disciplinary personnel each week. It was found that there was 11.5% agreement and 88.5% disagreement in the Grooming category; Eating, 46.2% agreement and 53.8% disagreement (but a high correlation coefficient); and Transfers, 46.4% agreement and 53.6% disagreement. The high difference in scores may be due to incomplete scores and inter-disciplinary scoring instead of intradisciplinary scoring. Further research requires a larger population and additional intra-disciplinary rating

Zinc–Acetate–Amine Complexes as Precursors to ZnO and the Effect of the Amine on Nanoparticle Morphology, Size, and Photocatalytic Activity

Zinc oxide is an environmentally friendly and readily synthesized semiconductor with many industrial applications. ZnO powders were prepared by alkali precipitation using different [Zn(acetate)2(amine)x] compounds to alter the particle size and aspect ratio. Slow precipitations from 95 °C solutions produced micron-scale particles with morphologies of hexagonal plates, rods, and needles, depending on the precursor used. Powders prepared at 65 °C with rapid precipitation yielded particles with minimal morphology differences, but particle size was dependent on the precursor used. The smallest particles were produced using precursors that yielded crystals with low aspect ratios during high-temperature synthesis. Particles produced during rapid synthesis had sizes ranging from 21–45 nm. The materials were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, thermogravimetric analysis, BET, and diffuse reflectance. The materials prepared using precursors with less-volatile amines were found to retain more organic material than ZnO produced using precursors with more volatile amines. The amount of organic material associated with the nanoparticles influenced the photocatalytic activity of the ZnO, with powders containing less organic material producing faster rate constants for the decolorizing of malachite green solutions under ultraviolet illumination, independent of particle size. [Zn(acetate)2(hydrazine)2] produced ZnO with the fastest rate constant and was recycled five times for dye degradation studies that revealed minimal to no reduction in catalytic efficiency

Zinc–Acetate–Amine Complexes as Precursors to ZnO and the Effect of the Amine on Nanoparticle Morphology, Size, and Photocatalytic Activity

Zinc oxide is an environmentally friendly and readily synthesized semiconductor with many industrial applications. ZnO powders were prepared by alkali precipitation using different [Zn(acetate)2(amine)x] compounds to alter the particle size and aspect ratio. Slow precipitations from 95 °C solutions produced micron-scale particles with morphologies of hexagonal plates, rods, and needles, depending on the precursor used. Powders prepared at 65 °C with rapid precipitation yielded particles with minimal morphology differences, but particle size was dependent on the precursor used. The smallest particles were produced using precursors that yielded crystals with low aspect ratios during high-temperature synthesis. Particles produced during rapid synthesis had sizes ranging from 21–45 nm. The materials were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, thermogravimetric analysis, BET, and diffuse reflectance. The materials prepared using precursors with less-volatile amines were found to retain more organic material than ZnO produced using precursors with more volatile amines. The amount of organic material associated with the nanoparticles influenced the photocatalytic activity of the ZnO, with powders containing less organic material producing faster rate constants for the decolorizing of malachite green solutions under ultraviolet illumination, independent of particle size. [Zn(acetate)2(hydrazine)2] produced ZnO with the fastest rate constant and was recycled five times for dye degradation studies that revealed minimal to no reduction in catalytic efficiency

Formulation and Aerosol Jet Printing of Nickel Nanoparticle Ink for High-Temperature Microelectronic Applications and Patterned Graphene Growth

Aerosol jet printing (AJP) is an advanced manufacturing technique for directly writing nanoparticle inks onto target substrates. It is an emerging reliable, efficient, and environmentally friendly fabrication route for thin film electronics and advanced semiconductor packaging. This fabrication technique is highly regarded for its rapid prototyping, the flexibility of design, and fine feature resolution. Nickel is an attractive high-temperature packaging material due to its electrical conductivity, magnetism, and corrosion resistance. In this work, we synthesized nickel nanoparticles and formulated an AJP ink, which was printed on various material surfaces. Thermal sintering experiments were performed on the samples to explore the redox behavior and to optimize the electrical performance of the devices. The nickel devices were heated to failure under an argon atmosphere, which was marked by a loss of reflectance and electrical properties due to the dewetting of the films. Additionally, a reduction mechanism was observed from these studies, which resembled that of nucleation and coalescence. Finally, multilayer graphene was grown on a custom-printed nickel thin film using chemical vapor deposition (CVD), establishing a fully additive manufacturing route to patterned graphene

Defect Induced Ferromagnetism in Undoped ZnO Nanoparticles

Undoped ZnO nanoparticles (NPs) with size ∼12 nm were produced using forced hydrolysis methods using diethylene glycol (DEG) [called ZnO-I] or denatured ethanol [called ZnO-II] as the reaction solvent; both using Zn acetate dehydrate as precursor. Both samples showed weak ferromagnetic behavior at 300 K with saturation magnetization Ms = 0.077 ± 0.002 memu/g and 0.088 ± 0.013 memu/g for ZnO-I and ZnO-II samples, respectively. Fourier transform infrared(FTIR) spectra showed that ZnO-I nanocrystals had DEG fragments linked to their surface. Photoluminescence (PL) data showed a broad emission near 500 nm for ZnO-II which is absent in the ZnO-I samples, presumably due to the blocking of surface traps by the capping molecules. Intentional oxygen vacancies created in the ZnO-I NPs by annealing at 450 °C in flowing Ar gas gradually increased Ms up to 90 min and x-ray photoelectron spectra (XPS) suggested that oxygen vacancies may have a key role in the observed changes in Ms. Finally, PL spectra of ZnO showed the appearance of a blue/violet emission, attributed to Zn interstitials,whose intensity changes with annealing time, similar to the trend seen for Ms. The observed variation in the magnetization of ZnO NP with increasing Ar annealing time seems to depend on the changes in the number of Zn interstitials and oxygen vacancies

Role of Oxygen Defects on the Magnetic Properties of Ultra-Small Sn\u3csub\u3e1−x\u3c/sub\u3eFe\u3csub\u3ex\u3c/sub\u3eO\u3csub\u3e2\u3c/sub\u3e Nanoparticles

Although the role of oxygen defects in the magnetism of metal oxide semiconductors has been widely discussed, it is been difficult to directly measure the oxygen defect concentration of samples to verify this. This work demonstrates a direct correlation between the photocatalytic activity of Sn1−xFexO2 nanoparticles and their magnetic properties. For this, a series of ~2.6 nm sized, well characterized, single-phase Sn1−xFexO2 crystallites with x = 0−0.20 were synthesized using tin acetate, urea, and appropriate amounts of iron acetate. X-ray photoelectron spectroscopy confirmed the concentration and 3+ oxidation state of the doped Fe ions. The maximum magnetic moment/Fe ion, μ, of 1.6 × 10−4 μB observed for the 0.1% Fe doped sample is smaller than the expected spin-only contribution from either high or low spin Fe3+ ions, and μ decreases with increasing Fe concentration. This behavior cannot be explained by the existing models of magnetic exchange. Photocatalytic studies of pure and Fe-doped SnO2 were used to understand the roles of doped Fe3+ ions and of the oxygen vacancies and defects. The photocatalytic rate constant k also showed an increase when SnO2 nanoparticles were doped with low concentrations of Fe3+, reaching a maximum at 0.1% Fe, followed by a rapid decrease of k for further increase in Fe%. Fe doping presumably increases the concentration of oxygen vacancies, and both Fe3+ ions and oxygen vacancies act as electron acceptors to reduce e−-h+ recombination and promote transfer of electrons (and/or holes) to the nanoparticle surface, where they participate in redox reactions. This electron transfer from the Fe3+ ions to local defect density of states at the nanoparticle surface could develop a magnetic moment at the surface states and leads to spontaneous ferromagnetic ordering of the surface shell under favorable conditions. However, at higher doping levels, the same Fe3+ ions might act as recombination centers causing a decrease of both k and magnetic moment μ

Novel Magnetic and Optical Properties of Sn\u3csub\u3e1−x\u3c/sub\u3eZn\u3csub\u3ex\u3c/sub\u3eO\u3csub\u3e2\u3c/sub\u3e Nanoparticles

In this work, we report on the effects of doping SnO2 nanoparticles with Zn2+ ions. A series of ∼2–3 nm sized Sn1−x ZnxO2 crystallite samples with 0 ≤ x ≤ 0.18 were synthesized using a forced hydrolysis method. Increasing dopant concentration caused systematic changes in the crystallite size, oxidation state of Sn, visible emission, and band gap of SnO2 nanoparticles. X-ray Diffraction studies confirmed the SnO2 phase purity and the absence of any impurity phases. Magnetic measurements at room temperature showed a weak ferromagnetic behavior characterized by an open hysteresis loop. Their saturation magnetization Ms increases initially with increasing Zn concentrations; however for x \u3e 0.06, Ms decreases. Samples with the highest Ms values (x = 0.06) were analyzed using an Inductively Coupled Plasma Mass Spectrometer, looking for traces of any magnetic elements in the samples. Concentrations of all transition metals (Fe, Co, Mn, Cr, and Ni) in these samples were below ppb level, suggesting that the observed magnetism is not due to random inclusions of any spurious magnetic impurities and it cannot be explained by the existing models of magnetic exchange. A new visible emission near 490 nm appeared in the Zn doped SnO2 samples in the photoluminescence spectra which strengthened as x increased, suggesting the formation of defects such as oxygen vacancies. X-ray Photoelectron Spectroscopy (XPS) confirmed the nominal Zn dopant concentrations and the 2+ oxidation state of Zn in the Sn1−x ZnxO2 samples. Interestingly, the XPS data indicated the presence of a small fraction of Sn2+ ions in Sn1−xZnxO2 samples in addition to the expected Sn4+, and the Sn2+ concentration increased with increasing x. The presence of multi-valent metal ions and oxygen defects in high surface area oxide nanoparticles has been proposed as a potential recipe for weak ferromagnetis

Dopant Spin States and Magnetism of Sn\u3csub\u3e1−x\u3c/sub\u3eFe\u3csub\u3ex\u3c/sub\u3eO\u3csub\u3e2\u3c/sub\u3e Nanoparticles

This work reports detailed investigations of a series of ∼2.6 nm sized, Sn1−xFexO2 crystallites with x = 0–0.10 using Mossbauer spectroscopy, x-ray photoelectron spectroscopy (XPS), electron paramagnetic resonance spectroscopy (EPR), and magnetometry to determine the oxidation state of Fe dopants and their role in the observed magnetic properties. The magnetic moment per Fe ion μ was the largest ∼6.48 × 10−3 μB for the sample with the lowest (0.001%) Fe doping, and it showed a rapid downward trend with increasing Fe doping. Majority of the Fe ions are in 3+ oxidation state occupying octahedral sites. Another significant fraction of Fe dopant ions is in 4+ oxidation state and a still smaller fraction might be existing as Fe2+ ions, both occupying distorted sites, presumably in the surface regions of the nanocrystals, near oxygen vacancies. These studies also suggest that the observed magnetism is not due to exchange coupling between Fe3+ spins. A more probable role for the multi-valent Fe ions may be to act as charge reservoirs, leading to charge transfer ferromagnetism