H2-TPR, XPS and TEM Study of the Reduction of Ru and Re promoted Co/γ-Al2O3, Co/TiO2 and Co/SiC Catalysts

Effects of Ru and Re promoters on Co-CoOx catalysts supported on γ-Al2O3, TiO2 and SiC were investigated to improve the understanding of the role of promoters of the active phase of Co-CoOx-Ru and Co-CoOx-Re. The influence of promoter addition on the composition and activity of the catalysts was characterized by several methods, such as H2-TPR, XPS, chemisorption and TEM. Furthermore, the role of support and metal-support interaction was especially studied and different support materials were compared. Based on the results, addition of promoter metals (Ru or Re) will most likely improve catalytic activity of Co/γ- Al2O3, Co/TiO2 and Co/SiC catalysts by increasing the active metal surface available for chemical reaction and by decreasing the size of the metallic nanoparticles. These changes in the catalytic activity were also associated with the changes in the ratio of metal and metal oxide phases in the surface composition as observed by XPS. Promoter metals also decreased the reduction temperatures needed for the reduction of Co3O4 to CoO and further to metallic cobalt. Significant decrease in reduction temperature was observed especially when ruthenium was used as the promoter.peerReviewe

Hydrocarbon production via Fischer-Tropsch synthesis from H-2-poor syngas over different Fe-Co/gamma-Al2O3 bimetallic catalysts

Fischer-Tropsch synthesis (FTS) at 20 bar. and 483 K, with H-2-poor syngas (H-2/CO ratio = 1.0) in order to simulate gasified biomass, was performed over Al2O3-supported catalysts with various ratios of Fe:Co (12 wt% bimetal) prepared by co-impregnation. Co was found to be incorporated into the Fe2O3 phase after calcination, at least for the iron-rich samples, while no evidence of Fe incorporated into Co3O4 was found. Upon reduction, most probably FeCo alloys were formed in the iron-rich bimetallic samples. The degree of reduction of the catalysts showed a non-linear behavior with respect to the Fe:Co ratio, but it is obvious that Co increases the reducibility of Fe. Alloying Co with small/moderate amounts of Fe improved the FT activity compared to the 100% Co catalyst at low conversion levels. Alloying Fe with small/moderate amounts of Co lowered the FT activity, but increased the relative water-gas-shift (WGS) activity compared to the 100% Fe catalyst. However, the overall WGS activity was very low for all catalysts, even with external water addition to the feed, resulting in low FT productivities (per gram catalyst) due to the low partial pressure of H-2. A higher Fe:Co ratio in the bimetallic catalyst generally resulted in higher relative WGS activity, but did not lower the H-2/CO usage ratio to the desired value of 1.0. For the Fe-containing catalysts, the space-time yield of hydrocarbons (HCs) decreased with increasing partial pressure of water or reduced space velocity, indicating an inhibition of water on the FT activity, most often resulting in low FT productivity under the conditions with highest relative WGS activity (usage ratios closest to the inlet H-2/CO ratio). Moreover, the co-impregnation technique resulted in a surface enrichment of Fe, at least for the Co-rich samples, covering the Co sites. For the bimetallic catalysts, both FT and WGS activities rapidly declined at high partial pressure of water due to deactivation by oxidation and sintering. However, the results indicate that WGS and FT proceeded over sites of different nature in the bimetallic catalysts. The bimetallic catalysts showed essentially no synergy effects with respect to HC selectivities and olefin/paraffin ratios, which partly can be explained by the use of a sub-stoichiometric H-2/CO ratio as feed. The higher the Fe content, the lower were the C5+ selectivity and C-3 olefin/paraffin ratio. Water addition increased the C5+ selectivity and C-3 Olefin/paraffin ratio and reduced the CH4 selectivity

Hydrocarbon production via Fischer-Tropsch synthesis from H-2-poor syngas over different Fe-Co/gamma-Al2O3 bimetallic catalysts

Fischer-Tropsch synthesis (FTS) at 20 bar. and 483 K, with H-2-poor syngas (H-2/CO ratio = 1.0) in order to simulate gasified biomass, was performed over Al2O3-supported catalysts with various ratios of Fe:Co (12 wt% bimetal) prepared by co-impregnation. Co was found to be incorporated into the Fe2O3 phase after calcination, at least for the iron-rich samples, while no evidence of Fe incorporated into Co3O4 was found. Upon reduction, most probably FeCo alloys were formed in the iron-rich bimetallic samples. The degree of reduction of the catalysts showed a non-linear behavior with respect to the Fe:Co ratio, but it is obvious that Co increases the reducibility of Fe. Alloying Co with small/moderate amounts of Fe improved the FT activity compared to the 100% Co catalyst at low conversion levels. Alloying Fe with small/moderate amounts of Co lowered the FT activity, but increased the relative water-gas-shift (WGS) activity compared to the 100% Fe catalyst. However, the overall WGS activity was very low for all catalysts, even with external water addition to the feed, resulting in low FT productivities (per gram catalyst) due to the low partial pressure of H-2. A higher Fe:Co ratio in the bimetallic catalyst generally resulted in higher relative WGS activity, but did not lower the H-2/CO usage ratio to the desired value of 1.0. For the Fe-containing catalysts, the space-time yield of hydrocarbons (HCs) decreased with increasing partial pressure of water or reduced space velocity, indicating an inhibition of water on the FT activity, most often resulting in low FT productivity under the conditions with highest relative WGS activity (usage ratios closest to the inlet H-2/CO ratio). Moreover, the co-impregnation technique resulted in a surface enrichment of Fe, at least for the Co-rich samples, covering the Co sites. For the bimetallic catalysts, both FT and WGS activities rapidly declined at high partial pressure of water due to deactivation by oxidation and sintering. However, the results indicate that WGS and FT proceeded over sites of different nature in the bimetallic catalysts. The bimetallic catalysts showed essentially no synergy effects with respect to HC selectivities and olefin/paraffin ratios, which partly can be explained by the use of a sub-stoichiometric H-2/CO ratio as feed. The higher the Fe content, the lower were the C5+ selectivity and C-3 olefin/paraffin ratio. Water addition increased the C5+ selectivity and C-3 Olefin/paraffin ratio and reduced the CH4 selectivity