Long-term performance of hybrid anodes for cathodic protection of reinforced concrete

© 2018 The Authors, published by EDP Sciences. The long-term performance of hybrid anode corrosion protection systems (UK invention disclosed in Patent GB2426008B) was investigated on six bridge structures as part of a holistic approach to corrosion risk management, using the performance criteria in ISO BS EN 12696:2016. The aim of the study was to review the effectiveness of current design approaches to meet the residual service life when the anodes are operating in the galvanic phase. This was achieved by analysing data on the general condition of the structures, the ongoing performance of the installed hybrid anodes, and assessing the subsequent corrosion risk. It was found that the six structures were generally in good condition, 1 to 8 years after refurbishment works, with low associated corrosion risk in areas protected by the hybrid anode systems. This is a positive finding for the wider implementation of hybrid anode systems as an alternative corrosion management technique. The reinforcement in the protected areas remained predominately in a passive condition, with calculated corrosion rates below the ISO 12696:2016 recommended threshold of 2mA/m

P5_5 Drag on Dragons

By comparison of the lift and drag forces of two dragons, one fat with a supplementary hydrogen source and one thin without, we have calculated the turning point velocity in which it is more beneficial to be either size. The wind velocity, or turning point velocity, was found to be 14.9 ms-1; below this value the fat dragon will be more advantageous and, conversely above, the thin dragon

Discussion: Hybrid anode concrete corrosion protection - independent study

Discussion: Hybrid anode concrete corrosion protection - independent stud

Understanding selectivity in radio frequency and microwave sorting of porphyry copper ores

Continuous high-throughput microwave treatment followed by infrared thermal imaging (MW-IR) has previously been shown to provide attractive separations for a number of porphyry copper ores, leading to rejection of a large proportion of barren fragments from ore-grade material or concentration of copper values from waste-grade material. However, the efficacy of the sorting process is reduced by the presence of hydrated clays and pyrite. Literature measurements have shown differences in the conductivity of pyrite and copper sulphides such as chalcopyrite at radio frequencies. In this work the potential of using radio frequency (RF) heating to exploit these differences and achieve improved selectivity between copper and iron sulphides, is investigated. For the first time a novel bulk materials handling and presentation method that facilitates even heating of angular ore fragments in parallel plate RF systems is discussed. The fragment-by-fragment thermal response of five ore samples under equivalent pilot MW-IR and RF-IR processing conditions is evaluated, showing that there is an increase in selectivity in the heating of hydrated clay minerals in RF compared to microwave. It is suggested, again for the first time, that selectivity in the microwave processing of ores containing semi-conducting minerals is due predominantly to magnetic absorption (induction heating) caused by eddy currents associated with the magnetic field component of electromagnetic energy. In radio frequency processing, where electric field is the dominant component, heating of semi-conducting minerals is limited by the electric field screening effect. This effect is demonstrated using synthetic fragments. Thermal response profiles of synthetic fragments show that approximately 2.5 times the mass of sulphide minerals to hydrated clay minerals would result in an equal temperature increase for microwave heated fragments in which the microwave-heating minerals are evenly disseminated throughout the matrix. This understanding provides the foundations for development of models incorporating different thermal responses for individual heated phases, alongside other textural and treatment variables, that can be used to predict how close to intrinsic sortability ores will perform in MW-IR and RF-IR without the need for extensive processing trials

Microwave assisted hydro-distillation of essential oils from fresh ginger root (Zingiber officinale Roscoe)

A solvent free in situ microwave hydro-distillation method for extraction of essential oil from fresh ginger root it presented. Extraction was conducted in a TE10n single-mode microwave cavity and variable power 2 kW generator operating at 2.45GHz. The main extracted components identified by gas chromatography (GC) were Zingiberene, α-Curcumene, β-Sesquiphellandrene and α-Selinene. At energy inputs of 0.40 kWh/kg higher powers and shorter exposure times, crucially did not degrade the highly volatile components (α-Pinene and Camphene) despite providing the highest essential oil yields. Optimum processing conditions were found to be 1000W (0.40kWh/kg) for 5 min, for whole ginger root, where 0.35g oil/100g plant was obtained. This was compared to a yield of 0.2g/100g plant in 150 min in using conventional hydro-distillation and 0.3g/100g plant in 90 min using a multi-mode microwave cavity-based hydro-distillation

Calibrated X-ray micro-tomography for mineral ore quantification

Scanning Electron Microscopy (SEM) based assessments are the most widely used and trusted imaging technique for mineral ore quantification. X-ray micro tomography (XMT) is a more recent addition to the mineralogy toolbox, but with the potential to extend the measurement capabilities into the three dimensional (3D) assessment of properties such as mineral liberation, grain size and textural characteristics. In addition, unlike SEM based assessments which require the samples to be sectioned, XMT is non-invasive and non-destructive. The disadvantage of XMT, is that the mineralogy must be inferred from the X-ray attenuation measurements, which can make it hard to distinguish from one another, whereas SEM when coupled with Energy-Dispersive X-ray Spectroscopy (EDX) provides elemental compositions and thus a more direct method for distinguishing different minerals. A new methodology that combines both methods at the mineral grain level is presented. The rock particles used to test the method were initially imaged in 3D using XMT followed by sectioning and the 2D imaging of the slices using SEM-EDX. An algorithm was developed that allowed the mineral grains in the 2D slice to be matched with their 3D equivalents in the XMT based images. As the mineralogy of the grains from the SEM images can be matched to a range of X-ray attenuations, this allows minerals which have similar attenuations to one another to be distinguished, with the level of uncertainty in the classification quantified. In addition, the methodology allowed for the estimation of the level of uncertainty in the quantification of grain size by XMT, the assessment of stereological effects in SEM 2D images and ultimately obtaining a simplified 3D mineral map from low energy XMT images. Copper sulphide ore fragments, with chalcopyrite and pyrite as the main sulphide minerals, were used to demonstrate the effectiveness of this procedure

P5_6 A Race in Space

By comparing solar and laser radiation sources, each driving a nano-satellite of mass 1 gram, we find that the solar sail is more advantageous up to 9.5 AU, and the laser sail is better beyond this distance. We also find that the laser sail has a constant acceleration throughout, but the solar sail acceleration decreases at a velocity of 150,000 ms-1

P5_4 Where’s Wall-E?

We have calculated that a fire extinguisher under incompressible flow has a ∆v = 4.1 ms-1 and a ∆v = 8.4 ms-1 under adiabatic flow. If Wall-E was to use fire extinguishers as a method of propulsion in space rather than NASA’s MMU (with ∆v = 25 ms-1) he would require 10 fire extinguishers for incompressible flow and 4 for adiabatic flow.

A tool for predicting heating uniformity in industrial radio frequency processing

Radio frequency energy is utilised for heating in a wide range of applications, particularly in the food industry. A major challenge of RF processing is non-uniform heating in loads of variable and angular geometry, leading to reduced quality and product damage. In the study, the specific effects of geometry on the heating profiles of a range of geometrically variable loads in an industrial scale RF system are analysed, and the understanding used to derive a general tool to predict heating uniformity. Potato was selected as a test material for experimental work; dielectric properties were measured using a 44mm coaxial probe. Analysis of simulated and experimental surface temperature profiles and simulated power uniformity indices indicates that the presence of vertices and edges on angular particles, and their proximity to faces perpendicular to the RF electrodes increases localised heating; faces parallel to the electrodes heated less than those faces perpendicular to them. Comparison of the same geometrical shape in different orientations indicates that overall power absorption uniformity can be better even when localised heating of edges is greater. It is suggested, for the first time, that the rotation of angular shapes within a parallel plate electric field can improve heating uniformity, and that this can be achieved through the design of bespoke electrode systems. A Euler characteristic based shape factor is proposed, again for the first time, that can predict heating uniformity for solid, dielectrically homogenous shapes. This provides industry with a tool to quickly determine the feasibility for uniform RF heating of different three dimensional shapes based on geometry alone. This provides a screening method for food technologists developing new products, allowing rapid assessment of potential heating uniformity and reducing the need for early stage specialist computational modelling