Emissions from a HGV Using Used Cooking Oil as a Fuel under Real World Driving Conditions

To maximize CO2 reduction, refined straight used cooking oils were used as a fuel in Heavy Goods Vehicles (HGVs) in this research. The fuel is called C2G Ultra Biofuel (C2G: Convert to Green Ltd) and is a fully renewable fuel made as a diesel replacement from processed used cooking oil, used directly in diesel engines specifically modified for this purpose. This is part of a large demonstration project involving ten 44-tonne trucks using C2G Ultra Biofuel as a fuel to partially replace standard diesel fuels. A dual fuel tank containing both diesel and C2G Ultra Biofuel and an on-board fuel blending system-Bioltec system was installed on each vehicle, which is able to heat the C2G Ultra Biofuel and automatically determine the required blending ratio of diesel and C2G Ultra Biofuel according to fuel temperature and engine load. The engine was started with diesel and then switched to C2G Ultra Biofuel under appropriate conditions. Exhaust emissions were measured using PEMS (Portable Emission Measurement Systems) on one of the trucks under real world driving conditions. Comparisons of emissions between neat diesel mode and blended fuel mode were made. The results show that C2G Ultra Biofuel can reduce particulate matter (PM) and CO emissions significantly compared to the use of pure diesel

Evaluation of the effect of fuel properties on the fuel spray and jet characteristics in a HGV DI diesel engine operated by used cooking oils

Fuel injection systems in modern diesel engines are designed and built to comply with very stringent environmental standards. They should also meet the highest level of fuel economy. Drivability, rapid response and easy and accurate control are a common demand. Changing the fuel characteristics could affect the performance of the fuel injection system. This study focuses on the evaluation of fuel spray characteristics of straight used cooking oil (SUCO) and its blends with petroleum diesel (PD) as a surrogate for pure PD. Used cooking oil blends have quite different physical properties from those of pure PD. Data for the lower heating value (LHV), density and viscosity were obtained from laboratory analysis. These data were merged with the physical and thermodynamic conditions of the diesel engine of interest to evaluate the dynamic behaviour of the fuel jet in 360° of crank rotation namely, the compression stroke, and the power stroke including the injection process. Engine operational conditions were calculated using a diesel dual thermodynamic cycle taking into account fuel injection adjustment at three different speeds, namely, idle speed, maximum torque speed and rated power speed. The results showed that fuel jet characteristics vary with SUCO content in the fuel blend. Two ranges of SUCO content in the blends were distinguished, 0 – 80% SUCO content and 80 – 100% SUCO content. Both showed a constant rate of change of jet characters per 10% increase in SUCO content in the fuel blend. Lower rates of change of fuel characters were observed at 0-80% SUCO content. The higher the temperature, the lower the rate of change of fuel jet characteristics

Real world emissions performance of a HDD truckwith SCR NOx control

Air quality issues and Real Driving Emissions (RDE) in urban areas of cities Factors that influence RDE. Experimental equipment HDD truck RDE test for Euro V with SR

Determination of carbon footprint using LCA method for straight used cooking oil as a fuel in HGVs

In order to improve energy supply diversity and reduce carbon dioxide emissions, sustainable bio-fuels are strongly supported by EU and other governments in the world. While the feedstock of biofuels has caused a debate on the issue of sustainability, the used cooking oil (UCO) has become a preferred feedstock for biodiesel manufacturers. However, intensive energy consumption in the trans-esterification process during the UCO biodiesel production has significantly compromised the carbon reduction potentials and increased the cost of the UCO biodiesel. Moreover, the yield of biodiesel is only ∼90% and the remaining ∼10% feedstock is wasted as by-product glycerol. Direct use of UCO in diesel engines is a way to maximize its carbon saving potentials. This paper, as part of the EPID (Environmental and Performance Impact of Direct use of used cooking oil in 44 tonne trucks under real world driving conditions) project, presents the life cycle analysis of Straight UCO (SUCO) in terms of CO2 and energy consumption, compared with the UCO biodiesel and petroleum diesel. The UK carbon calculator developed by UK Department for Transport was used for the calculations. The results show that SUCO renewable fuel can reduce the WTW carbon footprint by 98% compared to diesel and by 52% compared to the UCO biodiesel