Spatial and temporal hydrochemical variations of the spring-fed travertine-depositing stream in the Huanglong Ravine, Sichuan, SW China

Automatic hydrochemical logging and in situ titration com­bined withlaboratory analysis were used to understand the spatial and temporal hydrochemical variations of the spring-fed, travertine-depositing stream in celebrated Huanglong Ravine, Sichuan, SW China. This is essential for protection of the Huanglong World Natural Heritage travertine land­scape. It was found that the deposition of travertine was due to very strong CO2 degassing from the water, leading to de­crease in pCO2 and specific conductivity (SpC), and increase in pH and SIc downstream from the Spring. However, regular downstream hydrochemical evolution was interrupted by di­lution withsnow-melt water and by renewed CO2 from some downstream springs. The chemistry of Huanglong Spring itself was stable at a diurnal scale thoughit was altered by the great Wenchuan earthquake of May 12 2008. However, in spring-fed pools downstream, pCO2 and SpC were lower, and pH and SIc were higher in daytime than at night, whichindicates that the deposition of travertine was faster during the daylight hours. This was due to the combined effects of higher water tempera­tures and higher aquatic algae photosynthesis. In addition, it was found that the phosphate concentration in the stream in­creased remarkably downstream in the tourist midseason, in­dicating water pollution by tourism activities. The increase of phosphate (an inhibitor of calcite precipitation) may be one of the reasons for the decrease in travertine deposition rates and accelerated propagation of discoloration by diatoms during the past decades, whichneeds to be given more comprehensive study and tackled in future for the protection of these world famous travertine deposits

Investigation of Humidity and Temperature Response of a Silica Gel Coated Microfiber Coupler

The humidity and temperature responses of a microfiber coupler (MFC) coated with silica gel are investigated. Two MFC structures with different waist diameters of 2.5 and 3.5 μm were fabricated by fusing and tapering two single-mode fibers using a microheater brushing technique. The influences of the coating thickness and tapered waist diameter on the sensing performance are analyzed. For the proposed sensor with a waist diameter of 2.5 μm and 8-layers thick coating, the change in the relative humidity (RH) results in an exponential blueshift with a maximum sensitivity of 1.6 nm/% RH in the range from 70 to 86% RH. In response to the temperature change, the sensor's transmission spectrum redshifts in a linear fashion with an average sensitivity of 0.55 nm/°C in the range from 20 to 40 °C. The study is important for the development of the proposed fiber structure as a humidity or temperature sensor

NH2+ implantations induced superior hemocompatibility of carbon nanotubes

NH(2)(+) implantation was performed on multiwalled carbon nanotubes (MWCNTs) prepared by chemical vapor deposition. The hemocompatibility of MWCNTs and NH(2)(+)-implanted MWCNTs was evaluated based on in vitro hemolysis, platelet adhesion, and kinetic-clotting tests. Compared with MWCNTs, NH(2)(+)-implanted MWCNTs displayed more perfect platelets and red blood cells in morphology, lower platelet adhesion rate, lower hemolytic rate, and longer kinetic blood-clotting time. NH(2)(+)-implanted MWCNTs with higher fluency of 1 × 10(16) ions/cm(2) led to the best thromboresistance, hence desired hemocompatibility. Fourier transfer infrared and X-ray photoelectron spectroscopy analyses showed that NH(2)(+) implantation caused the cleavage of some pendants and the formation of some new N-containing functional groups. These results were responsible for the enhanced hemocompatibility of NH(2)(+)-implanted MWCNTs

Oxygen isotope composition of surface snow collected along the traverse route from Zhongshan Station toward Dome A, Antarctica

Oxygen isotope composition of surface snow sampled in the austral summer of 1998/1999 along the traverse route from Zhongshan Station toward Dome A, Antarctica is measured with the conventional mass spectrometer technique. The results of measurement show that oxygen isotope composition of surface snow varies in a wide range from -22.51‰ to -50.67‰, and has a tendency that isotopic values gradually decrease with increase of distance from Zhongshan Station and altitude. Linear regression analysis indicates that there exists good correlation between oxygen isotope composition of surface snow and distance from Zhongshan Station, altitude and/or latitude, which actually reflects the close relation between stable isotope composition and air temperature

High sensitivity ammonia gas sensor based on a silica gel coated microfiber coupler

In this paper, a high sensitivity ammonia gas sensor is proposed based on a silica gel coated microfiber coupler (MFC). The MFC structure is formed by the two tapered fibers with 3 μm waist diameter each, which were fabricated by using a customized microheater brushing technique. Silica gel coating was prepared by a sol-gel technique and applied on the surface of the MFC as a thin layer. The spectral characteristics of the proposed sensor were studied under various ammonia gas concentrations. The experimental results show that the coating thickness strongly affected the sensitivity of the MFC-based sensor to ammonia gas concentration. For the sensor with a 90 nm silica gel coating thickness, the highest measurement sensitivity is 2.23 nm/ppm for ammonia gas concentration, and the resolution is as good as 5 ppb, while the measured response and recovery times are ~ 50 and 35 seconds, respectively. Finally, it is demonstrated that the proposed sensor offers good repeatability and selectivity to ammonia gas

Mesoporous TiO

Mesoporous anatase TiO2 micro-nanometer composite structure was synthesized by solvothermal method at 180°C, followed by calcination at 400°C for 2 h. The as-prepared TiO2 was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), and Fourier transform infrared spectrum (FT-IR). The specific surface area and pore size distribution were obtained from N2 adsorption-desorption isotherm, and the optoelectric property of the mesoporous TiO2 was studied by UV-Vis absorption spectrum and surface photovoltage spectra (SPS). The photocatalytic activity was evaluated by photodegradation of sole rhodamine B (RhB) and sole phenol aqueous solutions under simulated sunlight irradiation and compared with that of Degussa P-25 (P25) under the same conditions. The photodegradation preference of this mesoporous TiO2 was also investigated for an RhB-phenol mixed solution. The results show that the TiO2 composite structure consists of microspheres (∼0.5–2 μm in diameter) and irregular aggregates (several hundred nanometers) with rough surfaces and the average primary particle size is 10.2 nm. The photodegradation activities of this mesoporous TiO2 on both RhB and phenol solutions are higher than those of P25. Moreover, this as-prepared TiO2 exhibits photodegradation preference on RhB in the RhB-phenol mixture solution

Comparative Study on Properties of Polylactic Acid Nanocomposites with Cellulose and Chitin Nanofibers Extracted from Different Raw Materials

Polylactic acid (PLA) was reinforced with ultralong cellulose and chitin nanofibers extracted from four raw materials by extrusion. The mechanical, rheological, thermal, and viscoelastic performances of four nanocomposites were comparatively studied in detail. The results showed that fibrillation of poplar was much easier than that of cotton, and fibrillation of crab shell was relatively hard as compared to prawn shell. The poplar CNFs/PLA composite exhibited the best mechanical properties among four nanocomposites due to the highest aspect ratio of nanofibers, while both the cotton CNFs/PLA composite and the crab shell CHNFs/PLA composite had low mechanical strength due to the relatively low aspect ratio. FE-SEM images showed that the ultralong nanofibers were uniformly dispersed in PLA matrix for all four samples with the water preblending method. The CTE values of the nanocomposites with 40 wt% nanofibers extracted from poplar, cotton, crab shell, and prawn shell were 69.5 × 10−6 K−1, 79.6 × 10−6 K−1, 77.2 × 10−6 K−1, and 75.3 × 10−6 K−1, respectively. All the results indicated that the aspect ratio of the nanofibers has a great influence on the performance of the composites, irrespective of the composites prepared by cellulose or chitin

Intergenerational Associations of Adverse Birth Outcomes: A Surveillance Report

Nebraska births between 1995 and 2005 were followed until 2018 to look for intergenerational associations of low birth weight (LBW) and preterm birth (PTB). Results from generalized estimating equations revealed that mothers born LBW preterm were more likely to deliver LBW (adjusted OR 1.94, 95% CI 1.39–2.71) or preterm (adjusted OR 1.65, 95% CI 1.20–2.27) than mothers born with normal weight or at term. In addition, mothers who had an LBW sibling were 44% more likely to have an LBW infant (OR 1.44, 95% CI 1.04–2.00). A consistent finding was also observed for mothers who had a PTB sibling (OR 1.47, 95% CI 1.10–1.95). Mothers who were LBW at birth or had any LBW siblings, especially two or more siblings, were more likely to repeat this adverse birth outcome. The same association was also observed in mothers who were born preterm