Evaluation of metallic filter media for sub-micrometer soot particle removal at elevated temperature

<p>Soot particle removal performance of two types of metallic filter media, sintered metal powder and sintered metal fiber, is experimentally evaluated as potential improvements to conventional ceramic filtration media for gasoline direct injection (GDI) engine PM after-treatment application. Soot collection efficiency and flow resistance of several grades of metallic media are measured at temperatures of 25, 350, and 650°C and a range of representative filtration velocities for sub-micrometer soot particles generated from a propane flame. Theoretical collection efficiency based on single fiber efficiency theory shows good agreement with experimental data for nearly spherical KCl particles at 350°C. Improved collection efficiency is observed for soot particles in the interception-dominated size range above ∼100 nm due to enhanced interception length. Soot collection is slightly enhanced at higher temperature, which is consistent with model predictions. Sintered metal fiber media are found capable of removing ∼75% of soot particles by mass with an incremental flow resistance of less than 1.5 kPa under 10 cm/s and 350°C, which is promising for gasoline particulate filter (GPF) application. The media level figure of merit (FOM) is used to quantify the soot collection efficiency versus flow resistance tradeoff of all media tested. It is found that due to their more open structure (higher porosity) sintered metal fiber media have FOMs nearly one order of magnitude higher than those of sintered metal powder media, and by analogy those of conventional wall flow ceramic media. This suggests that sintered metal fiber media represents an attractive alternative to ceramic media for designing GPFs; however, further research into creating comparable surface area to the honeycomb structures used for wall flow filters is needed to extract the full potential of metal fiber media.</p> <p>Copyright © 2017 American Association for Aerosol Research</p

Penetration of Sub-50 nm Nanoparticles Through Electret HVAC Filters Used in Residence

<div><p>Pleated electret HVAC filters are often used in residence to mitigate the particles that originate both indoors and outdoors. These filters are usually tested with particles larger than 300 nm. However, residential particles can contain a significant amount of nanoparticles with size below 50 nm due to cooking, smoking, cleaning, wood burning, and outdoor infiltration. In order to characterize the nanoparticle removal by electret HVAC filters, penetrations of 3–50 nm silver nanoparticles through five different flat sheet electret media used in commercial residential HVAC filters were tested with face velocities of 0.05, 0.5, and 1.0 m s⁻¹. Experimental results showed that all media had significantly high penetrations with 0.35–0.8 at the most penetrating particle sizes (MPPSs) for all three velocities, which were in the sizes of 10–30 nm. A model based on single fiber theory for particle penetration predictions was used and compared with the experimental data. Results showed that the model predicted the nanoparticle penetrations very well for all media and all face velocities tested. According to the model, for enhancing the nanoparticle efficiency of the current commercial HVAC filters, the fiber diameter should be reduced or the number of pleats should be increased. However, by doing these, pressure drop and cost may be largely increased. On the other hand, this study found the existing commercial mechanical HVAC filters were much capable for sub-50 nm nanoparticle removal when their minimum efficiency reporting values (MERVs) were larger than 13 and it is concluded mechanical HVAC filters can do a better job than electret ones. However, the quality factor analysis showed electret filters could be regarded as the best filter media for removing particles smaller than 300 nm.</p><p>Copyright © 2015 American Association for Aerosol Research</p></div

Characterization of nanosized silica size standards

<p>Nanosized silica size standards produced with a sol–gel synthesis process were evaluated for particle size, effective density, and refractive index in this study. Particle size and effective density measurements were conducted following protocol from the National Institute of Advanced Industrial Science and Technology (AIST) in Japan. Particle sizes were measured via electrical mobility analysis using a differential mobility analyzer (DMA) at sheath flow rates (<i>Q</i>_sh) of 3.0 and 6.0 L/min and a constant aerosol flow rate (<i>Q</i>_a) of 0.3 L/min. The measured mean and mode diameters agreed well with the labeled sizes in the size range 40–200 nm, with differences ranging from 0.03% to 0.8%, well within the labeled expanded uncertainties (95% confidence intervals) of 1.8%–2.2%. The coefficient of variation (CV) of the size distribution was 0.012–0.027 for 40–200 nm. Particle sizes measured for 20 nm and 30 nm standards showed size differences with respect to the certified sizes of 1.7% and 8.3% at <i>Q</i>_sh = 6.0 L/min, but the size distributions were narrow, with CV = 0.047–0.064. The average effective density for the range 40–200 nm measured with an aerosol particle mass analyzer (APM) was 1.9 g/cm³. The real component of the refractive index measured with an optical particle counter (OPC) was 1.41 at a wavelength of 633 nm. All properties (size, effective density, and refractive index) were stable and could be measured with good repeatability. From these evaluations, it was found that the nanosized silica size standards have good characteristics for use as size standards and constitute a feasible alternative to PSL particles.</p> <p>© 2017 American Association for Aerosol Research</p

All-Nanofiber-Based Ultralight Stretchable Triboelectric Nanogenerator for Self-Powered Wearable Electronics

The flexible and stretchable electronics have been considered as next-generation electronics. Stretchable triboelectric nanogenerators (S-TENGs) with both multifunction and comfort have become a hot field of research for wearable electronic devices recently. Here, we designed an all-nanofiber-based, ultralight, S-TENG that could be softly attached on skins for motion energy harvesting and self-powered biomechanical monitoring. The S-TENG consisted of only two nanofiber membranes: a polyvinylidene fluoride nanofiber membrane (PVDFNM) supported by thermoplastic polyurethane nanofiber membrane (TPUNM) was used as the frictional layer, and a multiwalled carbon nanotube (MWCNT) conductive material screen-printed on the TPUNM was used as the electrode layer. Due to the excellent stretchability of TPUNM, the S-TENG could generate electricity under various types of deformation, and regains its original performance after intense mechanical extension, even if it is partially cut or damaged. Owing to the great electronegativity of PVDFNM, the device generated a maximum voltage of 225 V and a current of 4.5 μA with an electrode area of 6 × 1 cm². The S-TENG has great potential applications in self-powered wearable devices, electronic skins, and smart sensor networks

All-Nanofiber-Based Ultralight Stretchable Triboelectric Nanogenerator for Self-Powered Wearable Electronics

The flexible and stretchable electronics have been considered as next-generation electronics. Stretchable triboelectric nanogenerators (S-TENGs) with both multifunction and comfort have become a hot field of research for wearable electronic devices recently. Here, we designed an all-nanofiber-based, ultralight, S-TENG that could be softly attached on skins for motion energy harvesting and self-powered biomechanical monitoring. The S-TENG consisted of only two nanofiber membranes: a polyvinylidene fluoride nanofiber membrane (PVDFNM) supported by thermoplastic polyurethane nanofiber membrane (TPUNM) was used as the frictional layer, and a multiwalled carbon nanotube (MWCNT) conductive material screen-printed on the TPUNM was used as the electrode layer. Due to the excellent stretchability of TPUNM, the S-TENG could generate electricity under various types of deformation, and regains its original performance after intense mechanical extension, even if it is partially cut or damaged. Owing to the great electronegativity of PVDFNM, the device generated a maximum voltage of 225 V and a current of 4.5 μA with an electrode area of 6 × 1 cm². The S-TENG has great potential applications in self-powered wearable devices, electronic skins, and smart sensor networks

All-Nanofiber-Based Ultralight Stretchable Triboelectric Nanogenerator for Self-Powered Wearable Electronics

The flexible and stretchable electronics have been considered as next-generation electronics. Stretchable triboelectric nanogenerators (S-TENGs) with both multifunction and comfort have become a hot field of research for wearable electronic devices recently. Here, we designed an all-nanofiber-based, ultralight, S-TENG that could be softly attached on skins for motion energy harvesting and self-powered biomechanical monitoring. The S-TENG consisted of only two nanofiber membranes: a polyvinylidene fluoride nanofiber membrane (PVDFNM) supported by thermoplastic polyurethane nanofiber membrane (TPUNM) was used as the frictional layer, and a multiwalled carbon nanotube (MWCNT) conductive material screen-printed on the TPUNM was used as the electrode layer. Due to the excellent stretchability of TPUNM, the S-TENG could generate electricity under various types of deformation, and regains its original performance after intense mechanical extension, even if it is partially cut or damaged. Owing to the great electronegativity of PVDFNM, the device generated a maximum voltage of 225 V and a current of 4.5 μA with an electrode area of 6 × 1 cm². The S-TENG has great potential applications in self-powered wearable devices, electronic skins, and smart sensor networks