Precision frequency measurements with interferometric weak values

We demonstrate an experiment which utilizes a Sagnac interferometer to measure a change in optical frequency of 129 kHz per root Hz with only 2 mW of continuous wave, single mode input power. We describe the measurement of a weak value and show how even higher frequency sensitivities may be obtained over a bandwidth of several nanometers. This technique has many possible applications, such as precision relative frequency measurements and laser locking without the use of atomic lines.Comment: 4 pages, 3 figures, published in PR

Ultrasensitive Beam Deflection Measurement via Interferometric Weak Value Amplification

We report on the use of an interferometric weak value technique to amplify very small transverse deflections of an optical beam. By entangling the beam's transverse degrees of freedom with the which-path states of a Sagnac interferometer, it is possible to realize an optical amplifier for polarization independent deflections. The theory for the interferometric weak value amplification method is presented along with the experimental results, which are in good agreement. Of particular interest, we measured the angular deflection of a mirror down to 560 femtoradians and the linear travel of a piezo actuator down to 20 femtometers

Optimizing the Signal to Noise Ratio of a Beam Deflection Measurement with Interferometric Weak Values

The amplification obtained using weak values is quantified through a detailed investigation of the signal to noise ratio for an optical beam deflection measurement. We show that for a given deflection, input power and beam radius, the use of interferometric weak values allows one to obtain the optimum signal to noise ratio using a coherent beam. This method has the advantage of reduced technical noise and allows for the use of detectors with a low saturation intensity. We report on an experiment which improves the signal to noise ratio for a beam deflection measurement by a factor of 54 when compared to a measurement using the same beam size and a quantum limited detector

Continuous phase amplification with a Sagnac interferometer

We describe a weak value inspired phase amplification technique in a Sagnac interferometer. We monitor the relative phase between two paths of a slightly misaligned interferometer by measuring the average position of a split-Gaussian mode in the dark port. Although we monitor only the dark port, we show that the signal varies linearly with phase and that we can obtain similar sensitivity to balanced homodyne detection. We derive the source of the amplification both with classical wave optics and as an inverse weak value.Comment: 5 pages, 4 figures, previously submitted for publicatio

Interferometric weak value deflections: quantum and classical treatments

We derive the weak value deflection given in a paper by Dixon et al. (Phys. Rev. Lett. 102, 173601 (2009)) both quantum mechanically and classically. This paper is meant to cover some of the mathematical details omitted in that paper owing to space constraints

Ultrasensitive Beam Deflection Measurement via Interferometric Weak Value Amplification

We report on the use of an interferometric weak value technique to amplify very small transverse deflections of an optical beam. By entangling the beam’s transverse degrees of freedom with the which-path states of a Sagnac interferometer, it is possible to realize an optical amplifier for polarization independent deflections. The theory for the interferometric weak value amplification method is presented along with the experimental results, which are in good agreement. Of particular interest, we measured the angular deflection of a mirror down to 40

Precision Frequency Measurements with Interferometric Weak Values

We demonstrate an experiment which utilizes a Sagnac interferometer to measure a change in optical frequency of 129 ± 7 kHz/√Hz with only 2 mW of continuous-wave, single-mode input power. We describe the measurement of a weak value and show how even higher-frequency sensitivities may be obtained over a bandwidth of several nanometers. This technique has many possible applications, such as precision relative frequency measurements and laser locking without the use of atomic lines

Optimizing the Signal-to-Noise Ratio of a Beam-Deflection Measurement with Interferometric Weak Values

The amplification obtained using weak values is quantified through a detailed investigation of the signal-to-noise ratio for an optical beam-deflection measurement. We show that for a given deflection, input power and beam radius, the use of interferometric weak values allows one to obtain the optimum signal-to-noise ratio using a coherent beam. This method has the advantage of reduced technical noise and allows for the use of detectors with a low saturation intensity. We report on an experiment which improves the signal-to-noise ratio for a beam-deflection measurement by a factor of 54 when compared to a measurement using the same beam size and a quantum-limited detector

Effect of Phosphorus on Cleavage Fracture in Κ-Carbide

To understand the origin of cleavage fracture which dominates in Fe(Mn)-Al-C alloys at a high phosphorus concentration, we performed first-principles study of the phosphorus effect on ideal cleavage energy and critical stress in κ-carbide, Fe3 AlC, a precipitate in the austenitic alloys. We find that phosphorus has higher solubility in Fe3 AlC than in γ-Fe and sharply reduces the cleavage characteristics of κ-carbide. We show that strong anisotropy of the Fe-P bonds in Fe3 (Al,P) C under tensile stress, leads to the appearance of large structural voids and may facilitate crack nucleation